Kompact VAG V2 Plumb Back has been specifically to suit the 2.0L VAG engine Unlike the standard, plastic valves that use un-reinforced diaphragms and are known to crack under increased boost, the new Kompact VAG V2 Plumb Back uses O-Ring sealed piston which, coupled with it's billet aluminium construction give it over 30PSI boost handling capability. Included with each Kompact VAG V2 Plumb Back kit: Model specific valve, Mounting screws and Spring clamps.

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

VW has encountered a problem with the FSI camshaft and cam follower that could lead to damage to your engine's cylinder head.

This small part can play quite a big role in your engine's well-being. It conveys the movement of your camshaft into power for the high pressure fuel pump by riding directly on the camshaft lobe.

 If it becomes worn to the point of breaking it can cause permanent damage to the camshaft, fuel pump, or both. It could also send metal particles into your cylinder head which can cause damage to moving parts. Without replacement, it is common for followers to have holes worn through them.

Replacing this follower as a form of preventative maintenance can save you from spending even more money and time replacing your fuel pump or camshaft from damage caused by a worn follower.

LEADING INTAKE FEATURES

• Increased airflow - Get the most out of your upgrades
• High-flow velocity stack - True performance design
• Sealed heatshield - Separates cold air from engine bay heat
• Perfect fitment - No modifications required to bolt-on
• Amazing sound - Releases awesome turbo and engine noise
• Looks great - Black powder coat, tight clearances, clean angles 

AUDI B8 A4 & A5 COLD AIR INTAKE

You're not just building a run of the mill bolt-on car with cheap imported parts. No, your Audi B8 A4 or A5 project deserves true performance designed mods and the best cold air intake available. This is not your average filter on a stick, IE engineers used specialized computer flow analysis software coupled with 3D scans of the engine bay to maximize performance. The result is a unique intake shape that optimizes flow and reduces air restrictions for an unmatched bump in power. Factory-like mounting solutions are used for a perfect fit and long life. Your new intake will fit like it was there stock, but perform and sound like a true motorsport intake design.

EASY INSTALLATION

Installation is quick and easy to install with basic tools. The process should take under an hour for most enthusiasts. CLICK HERE to view and download the IE B8/B8.5 A4/A5 Cold Air Intake Install Guide.

VEHICLE FITMENT

• Audi - A4 2009-2015 (B8-B8.5) 2.0T
• Audi - A4 Allroad 2009-2015 (B8-B8.5) 2.0T
• Audi - A5 2009-2015 (B8-B8.5) 2.0T

Description:

PRODUCT FEATURES 

• Helps prevent carbon build-up
• Keep your engine running clean
• Complete kit, ready to install
• Installs under the factory engine cover
• All components are black for a sleek stealth install
• Braided stainless steel/nylon hose

TECHNICAL DETAILS

Prevent crankcase oil fumes from condensing and filling your turbo piping, intercooler, and intake manifold. The simple to install and quality looking IE catch can kit is a must for your VW MK5 & MK6 2.0T TSI engine.

A catch can works well to catch all of the oil fumes that are omitted from the valve cover breather, removing the faulty factory oil separator in the process. This not only removes the oil mist that is found everywhere but will greatly help reduce carbon buildup on the intake valves, a common problem on TSI engines, which relates to power loss and poor drivability.

Our kit includes the necessary valve cover breather adapter to remove the separator and plumb the catch can using the two included -10AN hoses. Using our catch can kit, you are not required to remove any of the emissions system or vent the catch can to the atmosphere, which can cause oil mist build-up in your engine bay. Our breather plate simply installs in place of the factory plastic breather plate located on top of the valve cover, while the catch can mounts to a custom bracket easily accessible on the passenger side of the vehicle.

This kit uses the Integrated Engineering billet recirculating catch can, which features our state-of-the-art baffle system to catch the oil mist and not let it pass back into the turbo inlet. This flawless catch can is fully serviceable, easily disassembling if needed. Draining the catch can is simple with the use of the included T handle drain valve, no tools necessary. This beautiful piece is finished with a bright black anodize finish, which maintains a stealthy appearance while looking great in your engine bay.

Everything you need to upgrade the PCV system on your Audi B8 2.0T TSI engine is included with this kit, with a very simple installation that takes less than an hour to install on average. This kit allows the use of the factory engine cover if desired, and the entire install is completely reversible if it ever needs to be removed for any reason.

COLD WEATHER CLIMATES

Catch can kits are designed for warm weather climates only. If you live in an area with sub-freezing temperatures in winter months, extra precaution must be taken as condensation in the catch can and lines can freeze and cause pressure to build up in the crankcase. We recommend checking the contents of the catch can frequently or removing the system entirely during cold winter months. Integrated Engineering is not responsible for any damage caused by improper servicing of the catch can.

FITMENT

AUDI - A4 B8 & B8.5 2.0T TFSI*
AUDI - A4 ALLROAD B8 & B8.5 2.0T TFSI*
AUDI - A5 B8 & B8.5 2.0T TFSI*
*Does not fit Flexfuel 5th injector vehicles with metal intake manifold. 

INCREASE POWER AND SOUND WITH A COLD AIR INTAKE

The IE Audi B9 A4 & A5 2.0T Cold Air Intake is the perfect addition to any engine bay. Give your Audi added horsepower, torque, snappier throttle response, and an aggressive sound. Typical peak gains from our CAI are roughly 10-20 Horsepower and Torque.

POWER GAINS

The ram air design, velocity stack, and massive 55-inchfilter inlet help deliver the most HP possible from a cold intake system.

Expect peak gains of 10-20+HP/TQ on tuned engines.

INCLUDED IN THE B9 IE CAI KIT

• IE Intake velocity stack & heatshield assembly
• IE Silicone turbo inlet pipe assembly
• IE 5” inlet performance air filter
• IE Turbo heat shield
• All necessary hardware (clamps, nuts, bolts, etc)

INCREASED AIR FLOW

This Intake delivers an impressive flow increase to feed your turbo. More cold air flow means more power; especially during the hot summer months. Ditch your stock restrictive airbox for the IE intake System.

DESIGN DETAILS

IE engineers set out to produce the highest performing cold air intake that looks great and fits like a factory installed part in your A4. The latest in computer design and 3D scanning technology were employed during the development process for a perfect fit and maximum performance. The final product resulted in the greatest performing and best-looking intake available.

HIGH-FLOW VELOCITY STACK

Delivering cold air to your engine is a must for making power. The velocity stack efficiently channels air as quickly as possible into the intake system. The velocity also functions as a solid mount for the air filter which means no intake pipes rattling on heat shields.

CUSTOM HEAT SHIELD

IE uses a three piece heat shield which performs and looks great. It effectively channels cold air from the front of the car to the massive performance filter. Furthermore, it eliminates the induction of hot air found in other locations of the engine bay. A second heat shield is mounted above the turbocharger to further protect against power robbing heat off the exhaust and turbo.

PERFECT FITMENT

This Intake fits B9 Audi A4 and A5 without any modification or installation hassles. The install process is simple and can be done quickly with basic tools. The fact that IE intake utilizes the factory airbox mounts ensures a perfect and hassle free fit. Additionally, the stock rubber mounts allow for engine movement which keeps intake components from getting damaged.

CLASSY AND CLEAN APPEARANCE

Wrinkle black powder coated velocity stack and heat shields result in a sleek and sporty appearance in any engine bay. As a final touch, all IE heat shields are finished with a classy, laser etched, stainless steel IE logo badge.

EASY INSTALLATION

Installation is a quick and easy install with basic tools. The process should take around an hour for most enthusiasts. CLICK HERE to view and download the IE B9 Cold Air Intake Install Guide.

INSTALL OVERVIEW VIDEO

DYNO POWER RESULTS

The following power result data was collected on our in-house Dynapack hub dyno. Dyno chart is as tested at 4500 feet altitude with SAE corrected numbers. Before and after results are direct back-to-back comparisons on a full bolt-on stage 2 B9 A4 2.0T engine. The only change made to the vehicle between testing is the swap from a stock intake with a new clean air filter to the IE Cold Air Intake Kit. Dyno power results are approximate and may vary from car to car.

HORSEPOWER & TORQUE DYNO CHART

HORSEPOWER & TORQUE POWER GAINS OVER STOCK

VEHICLE FITMENT

• Audi - A4 2015+ (B9) 2.0T
• Audi - A5 2015+ (B9) 2.0T
• Audi - A4 Allroad 2015+ (B9) 2.0T

This intake does not fit cars that have a MAF housing/sensor.

AUDI B9 2.0T TUNE FEATURES

HOW TO TUNE YOUR B9 A4 or A5

IE ECU Stages for your Audi B9 engine are available for stock (Stage 1) or with modified hardware for Stage 2. Read below to determine the best stage for your build!

In order to flash your vehicle, you will need an IE POWERlink Direct-port Flash Tool (sold separately) and a Windows 7+ powered laptop. Already own an IE POWERlink cable? Contact us to purchase upgrade credits, there is no fee to upgrade tunes and you only pay the difference in tune cost.

Follow the link provided with your IE POWERlink Flash Tool to download our Flash Wizard software and follow the on-screen directions to tune your Audi in a matter of minutes!

WHAT DOES THE IE AUDI B9 ECU TUNE DO?

Your ECU (Engine Control Module) is a computer loaded with maps to control the operating conditions of your Audi 2.0T engine. The factory calibration is designed to function with stock installed hardware, meet new car regulated standards, and de-powered to not compete with higher performance models. IE's motorsport recalibration brings your engine to life by unleashing its full performance potential on stock hardware or to match your installed hardware upgrades while maintaining reliability and factory-like comfort. This is how your turbocharged Audi should have felt from the factory!

AVAILABLE AUDI 2.0T STAGES

The IE Stage 1 Audi B9 A4 or A5 TSI tune delivers an aggressive power upgrade without having to install any hardware modifications. Perfect for customers looking for a big jump in power without adding any additional hardware or to get the most out of your installed intake and intercooler. In a matter of minutes, your new ECU Tune will deliver a massive boost in performance.

Stage 1 recommended hardware
-IE Cold Air Intake
-IE Intercooler

 

Looking to maximize the performance of your stock engine and turbo? IE Stage 2 Upgrade fine-tunes the ECU to match installed aftermarket hardware allowing the turbocharger to breath free and improve power gains across the powerband. This is the maximum power available from a stock turbo car.

Stage 2 required & recommended hardware 
-IE Performance Downpipe (required)
-IE Cold Air Intake (recommended)
-IE Intercooler (highly recommended)

 

POWER GAINS

EASY INSTALLATION - TUNE FROM HOME

Required to flash your tune, The IE POWERlink cable gives you control to unlock your engine’s true potential from your own garage or driveway. Quickly reflash your B9 Audi with your choice of ECU Stage through the cars OBD-II port. Upgrade tune stages to match installed hardware, take advantage of different fuel octanes, flash to stock, perform engine diagnostics, read/clear codes and gather high-quality operating data via data-logging.

VEHICLE FITMENT

• Audi - B9 A4 Quattro 2016+ with 2.0T engine*
• Audi - B9 A5 Quattro 2016+ with 2.0T engine*
• Audi - B9 A4 Quattro Allroad 2017+ with 2.0T engine*

*For all wheel drive (Quattro) vehicles only, does not support front wheel drive engines at this time.