Search results for 'reduce'

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

Autotech is the premier manufacturer of fuel pump upgrades for the FSI engine because our kit offers the highest quality, solid engineering, and great value.

Our HPFP Kit can achieve flow rates 50% higher than the original pump, essentially removing pump limitations from the equation, even on high-end turbo upgrades.

Our HPFP kit continues to be the benchmark that imitators strive to reach. However, Autotech’s HPFP Kit is not easily duplicated.

There are many reasons why Autotech’s Kit is superior. Here are a few:

~Each piston (9.8mm) and cylinder in Autotech HPFP kit undergo high-precision grinding processes many times during their manufacture, ensuring that the most precise tolerances are maintained through the final step. Not the cheapest way to make them, but the best way.

~Each piston and cylinder are match-ground and serialized to ensure absolute precision and the utmost longevity.

~Autotech was the first to incorporate plasma DLC coating on HPFP components to reduce friction losses and increase performance. Others have tried to follow by adding a coating to their parts. However, the DLC process alone is not enough – it is not a cure for substandard precision – the parts must be engineered specifically for the process to take full advantage: Autotech’s are. The success we have in the field can attest to that.

~HPFP-specific mapping is now commonly available from tuners worldwide.

Tuners trust Autotech’s HPFP in their conversions and upgrades because it works, and works well.

Fits VW/Audi 2.0T FSI 2006-2008.5, MK6 Golf R.

2 kits required for V8 4.2L FSI Audi B7 RS4 / R8 V8 / B8 S5 models.

Autotech is the premier manufacturer of fuel pump upgrades for the FSI engine because our kit offers the highest quality, solid engineering, and great value. 

Upon installing the Volkswagen fuel pump, notable differences include 5% Horsepower & Torque increase on stock mapping.

Our HPFP kit continues to be the benchmark that imitators strive to reach. However, Autotech’s HPFP Kit is not easily duplicated. 

There are many reasons why Autotech’s Kit is superior. Here are a few: 

~Each piston (11.66mm) and cylinder in AutoTech High-Pressure Fuel Pump kit undergo high-precision grinding processes many times during their manufacture, ensuring that the most precise tolerances are maintained through the final step. Not the cheapest way to make them, but the best way.

~Each piston and cylinder are match-ground and serialized to ensure absolute precision and the utmost longevity.

~Autotech was the first to incorporate plasma DLC coating on HPFP components to reduce friction losses and increase performance. Others have tried to follow by adding a coating to their parts. However, the DLC process alone is not enough – it is not a cure for substandard precision – the parts must be engineered specifically for the process to take full advantage: Autotech’s are. The success we have in the field can attest to that.

Tuners trust Autotech’s HPFP in their conversions and upgrades because it works, and works well. 

Applications:
Audi - 8V A3 & S3 (MK3) - EA888 Gen 3 - 1.8 TFSI and 2.0 TFSI
Audi - 8S TT / TTS (MK3) - EA888 Gen 3 - and 2.0 TFSI
Audi - TTRS 8S / RS3 8V (MK3) - EA888 Gen 3 
VW - Golf / GTI / R (MK7) - EA888 Gen 3 - 1.8 TSI and 2.0 TSI
VW - Jetta - EA888 Gen 3 - 1.8 TSI and 2.0 TSI
Audi - S1 EA888 Gen 3 - 2.0 TFSI



Note: some 1.8 TSFI non-USA Market cars do not use this internal pump style (physically check for a hex-cap recess for our 103T tool) 

Also some 2.0T Jettas and Beetles with engine codes CPLA & CPPA do not use this internal pump style (sealed pump unit similar to MK6 GTI sorry)

Assembly tool required, part # 10-127-103T (see related parts above) 
103K/203K Install Instructions

Description:

Struggling with the OEM Turbo Valve? Need to add that unique boost pressure sound? Make sure to get your hands on All New Re-Designed Leyo Motorsports latest in-house designed Diverter Valve. Leyo Motorsport Diverter Valve multi piece design is built and engineered to solve the failure issues associated with the OEM solenoid valves and their diaphragm resulting in boost leaks. It is built from 6061 Billet Aluminum with hard coated Anodized finish with an internal serviceable piston based design that provides greater reliability over the OEM as well as quicker throttle and turbo response. All components are made in-house by Japan CNC’s, inspected to 0.01mm tolerance by Japan CMM, laser etched and race proven.

Leyo Motorsport Diverter vavle has a unique and fully tested internal piston compared with other brands in order to get the maximum results in power. We are offering a stronger, more durable and reliable valve compared to the OEM unit. We do have uprated valve spring in stock that is sold separately.

Specifications:

• Made from the highest quality T6061 billet aluminium construction.

• Direct OEM replacement..

• Improved throttle response

• Consistent turbo boost.

• Reduced turbo lag .

• Fully compatible with OE electronics.

• Fully serviceable piston .

• Holds up to 600HP. (with optional uprated spring kit)

* Note : This DV kit comes supplied with BLACK / WHITE / YELLOW Spring. Uprated BLUE / RED Spring is Available for purchase. 

SUGGESTED SPRING INSTALLATION

Above figure is only preference. Please refer vehicle modification needs.