CTS Turbo is proud to announce an official release of our new K04 Upgrade for 2.0T FSI/TSI Transverse Engines.
Our engineers designed the compressor cover and exhaust housing to work with the larger K04 CHRA, exactly how intended. While other manufacturers simply install a larger K04 CHRA into a small factory-spec housing.
Beware of these hybrid builds, they are not made to provide optimal flow for the larger turbine wheel and can lead to poor performance and premature failure.
High-quality castings are CNC machined to replace your factory turbocharger and do not require any additional parts to be installed. All you need to run this K04 2.0T FSI/TSI Transverse Turbocharger Upgrade is a tune for your ECU and a performance downpipe.
This kit is by far the best ‘bang for the buck’ modification available for VW and Audi enthusiasts with the 2.0T FSI and 2.0T TSI engine. With proper tuning and supporting mods, this turbo will support 350HP/360TQ!
Features:
CTS-spec K04 CHRA with heavy-duty thrust bearings
Billet compressor wheel (MFS – machined from solid)
K04-specific compressor and turbine housing. NOT A HYBRID!
OEM+ manufacturing tolerances
VSR high-speed balanced
Direct-fit factory replacement
OEM installation kit included
Compatible with any K04-specific tune
Compatible with factory turbo outlet pipe (both FSI and TSI). Not compatible with aftermarket stock turbo outlet pipes
ROW vehicles, please confirm fitment with your CTS Turbo dealer.
Additional parts required:
K04-specific software tuning
CTS Turbo or other performance downpipe
Additional parts recommended:
CTS Turbo Cold Air Intake
CTS Turbo Direct-Fit Intercooler Kit
CTS Turbo High Flow Turbo Outlet Pipe (EA888 only)
S3 Fuel Injectors and HPFP upgrade (EA113 engines only)
H&R Sport Springs - Volkswagen Golf R Wagon (MK7)
Sport Spring kits are H&R’s number one selling product. Enhance the look of your vehicle with a reduced fender well gap. H&R Sport Springs lower the vehicle center of gravity and reduce body roll for better handling. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. If you are only looking to improve one part of your vehicle’s suspension, you cannot go wrong with installing Sport Springs. Fun to drive, H&R Sport Springs are the number one upgrade for your vehicle.
H&R Special Springs are high quality products—they will not set or sag, they are designed and manufactured to be strong, resilient, and more durable than other automotive coil springs. All H&R springs are crafted from a special (hf) 54SiCr6 spring steel to ensure premium quality and performance. H&R Springs are shot-peened to increase their life by more than 200%. All production is completed in-house so product quality is ensured. Each spring is 100% tested before leaving H&R’s ISO9001 certified production facility in Germany.
Features:
Lowers the center of gravity
Reduces body roll
Reduces wheel gap
Lower wind resistance
Front Drop: 25mm
Rear Drop: 25mm
MK7 Golf/GTI/Golf R (up to production date Sept 27, 2015)
8V Audi A3/S3 (up to production date Sept 27, 2015)
MK3 Audi TT/TT-S (up to production date Sept 27, 2015)
DESCRIPTION
CTS Turbo is pleased to release our high flow turbo outlet pipe for 7-speed DSG MQB vehicles such a MK7.5 VW GTI, MK7.5 VW Golf R, MK7 VW GLI and 8V.2 Audi S3. The factory turbo outlet pipe is constructed from flimsy plastic and is quite narrow, which results in an extreme airflow restriction. The CTS Turbo high flow turbo outlet pipe kit is constructed from mandrel-bent 60mm aluminum tubing. A custom 5-ply silicon coupler makes installation simple! The CTS Turbo high flow turbo outlet pipe kit also replaces all the factory charge piping between the turbocharger compressor housing and factory intercooler.
Product Details:
60mm aluminum piping with CTS logo
5-ply silicon coupler
Factory mounting points are used for perfect fitment
Durable black powdercoat finish
For 7-speed DSG/S-tronic transmissions only
Compatible with factory and upgraded turbos
Compatible with factory and upgraded intakes
Compatible with factory and upgraded intercoolers
Parts Included:
Upper turbo outlet silicon
Lower turbo outlet pipe
2 clamps
Installation hardware
Fitment:
2018+ VW Golf R DSG 7-speed
2019+ VW GLI DSG 7-speed
2019+ VW GTI DSG 7-speed
2018+ Audi A3 S-Tronic 7-speed
2018+ Audi S3 S-Tronic 7-speed
2018+ Audi TT, TT-S S-Tronic 7-speed
NOT COMPATIBLE WITH 6-SPEED DSG, AUTOMATIC or MANUAL TRANSMISSION MODELS, SEE CTS-IT-275
This is a direct replacement for Part Number 06H 131 111. - It will fit EA888 Gen 3 engine with IHI Turbo IS20 IS38
On a 2.0L Porsche Macan, this muffler delete gave an additional 10bhp during dyno tests.
Forge has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (TSI) (EA888 engine). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.
This will replace OEM part numbers 06H 145 710D, 06F 145 710G, & 06H 145 710 C
Forge Motorsport is proud to release the latest version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CJXB, CZPA, and CJXC;US codes CPLA and CPPA) including Golf MK7 R
This valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. It has also been proven in cars running over 600bhp!
This new valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.
We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner
In The Box: 1 x FMDVMK7R Valve 1 x Wiring Harness 1 x Solenoid, Bracket, and Screws 1 x Uprated Blue Spring 10 x Cable Ties 1 x 1000mm of 4mm Vacuum Tube 1 x 5mm T Piece 1 x Instructions 1 x Forge Keyring and Sticker
The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team for the EA888 TSI vehicles, the Forge turbo blanket is designed to assist in the protection and prolonged life of the engine components.
The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it shouldnot be routinely removed as you will likely damage the blanket.
Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers:
T4
T5
T25
The Garrett GTX28 and GTX30 Range
Borg Warner EFR6258
Interior Surface:
· Max Temperature Rating: 2300°F/1260°C · Continuous Use Limit: 1832°F1000°C
Exterior Surface:
· Direct Contact Limit: 1800°F/982°C · Radiant Heat Limit: 2500°F/1371°C
At CTS Turbo we are proud to announce our new air intake system for the MK5 R32. The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our high quality silicones fit seamlessly with the OEM MAF flange allowing for smooth entry of cold air into the the engine providing peak power gains ranging from 9-15HP. All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.
Product Details
The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation.
Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle!
You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device.
In house designed and built in the USA, our Boost Tap includes the following:
Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap
3 Vacuum Ports with 1/4" Hose Barb Fittings
3 Vacuum Set Screws
Medium Strength Thread Lock
OEM Securing Clip
Manifold Pierce Alignment Tools
In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!
IE ULTIMATE PERFORMANCE VALVE SPRING & RETAINER KIT FOR 2.0T TSI
This high-quality IE Valve Spring & Titanium Retainer kit features spring rates optimized to match your 2.0T FSI/TSI specifications and provide proper valve control preventing valve float in high-power and high-revving applications.
LEADING FEATURES
Protects against engine failure from valve float
Safely increase your rev limit and power band
Nan-peened valve springs provide long life
In-house CNC machined retainers from titanium
Optimized design for all EA113/EA888 2.0T engines
Highest quality spring material available in the world
Torture tested in-house for high-power reliability
INCLUDED IN KIT
16 PRECISION WOUND INTAKE/EXHAUST VALVE SPRINGS
8 EXACT TOLERANCE TITANIUM INTAKE RETAINERS
8 EXACT TOLERANCE TITANIUM EXHAUST RETAINERS
WHY DO I NEED A SPRING & RETAINER KIT?
Increasing your engine's power output often comes with modifications that require more RPMs to get the most out of it, such as larger turbochargers, tuned intake manifolds, and high-output software tunes. Upgrading those components without changing out the valve springs can leave you with a short power band or cause valve float and other significant damage.
ONLY TRUST YOUR ENGINE TO THE BEST
Other cheap valve spring kits are often designed by simply finding a spring that is stiffer and will fit. Those are also not usually a good compromise because many times they are the wrong stiffness, and often poorly constructed. A broken valve spring can cause total engine failure and destroy everything that you have put hard work and money into. Our kits are the only spring and retainer kits on the market designed by someone with a working knowledge of the unique valvetrain in the VW & Audi EA113 FSI engines, and what the spring requirements actually are.
THE ULTIMATE SPRING & RETAINER KIT
Manufactured out of the best spring wire in the world IE valve springs use a patented multi-stage shot peening process that further reduces failure rates. Our titanium retainers are machined with an excellent surface finish and tight tolerance control for a long lifespan. Each application is thoroughly tested to perform on these engines right here in our test facility in Salt Lake City, Utah. Our spring and retainer kits are the best matched, most tested parts on the market. Purchasing a set will ensure that your engine runs at maximum performance and reliability.