This is a CTS Turbo universal 3″ low profile cone filter, it has a tapered design to fit in tight spots. These filters are used in our MK4 1.8T, 2.0T FSI, 2.oT TSI, B8 A4 intake kits. Also these filters can also be used in a custom big turbo application.
3.0″ Inlet x 8.0″ Long x 5.0″ Wide High quality molded silicon base and cap Stainless steel clamp
Whiteline offset strut tops allow for extra negative camber and positive caster to improve steering response, steering feel and reduced movement to ensure wheel alignment stability through a high quality spherical bearing. Perfect for the high performance street or track day weapon, providing improved tyre life and extra grip during high speed / high load cornering.
Now fully compatible with all 2018-2020 Audi RS3/TTRS 2.5T DAZA and DNWA engines, this is one kit to fit them all!
CTS Turbo is proud to announce our improved 8V, 8V.2/8S Audi RS3/TTRS Throttle Body Inlet Kit for DAZA and DNWA
Our high flow throttle body inlet is designed it to be larger, but also more aerodynamic than the stock part. Our inlet has a 56% internal volume increase over the stock inlet. Using the latest CAD software, the shape of the inlet tract was flow optimized and cast from aluminum for best performance. All critical parts were CNC machined to ensure perfect fitment and performance.
We have also included our machined throttle body spacer from with two additional ports for boost reference and methanol injection; as well and a high-flow 2.75″ throttle inlet pipe. Custom-made silicone couplers and t-bolt clamps allow for seamless, easy installation.
Features:
CAD optimized for maximum flow, 56% larger than factory
Cast aluminum throttle body elbow, billet aluminum spacer
CNC machined in house for perfect fitment
Direct replacement for factory parts between the cold side of the intercooler and the throttle body
HP gain of up to 20hp on stock turbo, even more with big turbo upgrades
Compatible with factory intake, CTS Turbo intakes and most other popular intakes (not compatible with Eventuri intake)
Compatible with factory and aftermarket intercoolers
Includes a large-bore 2.75″ charge pipe and custom silicone couplers
Two extra 1/8″ NPT bungs on the charge pipe for watermeth nozzles
Compatible with 1-bolt and 2-bolt pressure sensors
DV flange is based on factory design
Includes hoses and fittings to install on 2019+ DNWA engines
Fitment:
8V and 8V.2 Audi RS3 (2018-2020) – DAZA and DNWA models
The CTS Turbo Golf R / FSI intake heat shield is designed to mount simply to the factory mounting points. With a brushed aluminium finish this heat shield not only reduces your intake temps, but dresses up the engine bay like no other
Product Details
The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation.
Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle!
You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device.
In house designed and built in the USA, our Boost Tap includes the following:
Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap
3 Vacuum Ports with 1/4" Hose Barb Fittings
3 Vacuum Set Screws
Medium Strength Thread Lock
OEM Securing Clip
Manifold Pierce Alignment Tools
In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!
At CTS Turbo we are proud to announce our new air intake system for the MK5 R32. The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our high quality silicones fit seamlessly with the OEM MAF flange allowing for smooth entry of cold air into the the engine providing peak power gains ranging from 9-15HP. All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.
Part No:
ESHY30NVKAS
RRP:
$850.00
Diameter [in]:
3"
Material:
Stainless Steel
Suppliers Product Group:
Axle Back System
Feature;
3″ Stainless steel pipe work
Varex rear Muffler
Direct swap with factory standard section
4″ double wall tips
Smartbox is NOT included
Installation instructions
Download Installation Instructions