H&R Lowering Springs - Audi Q3

H&R Lowering Springs - VW Polo GTI

H&R 35MM LOWERING SUSPENSION SPRINGS

Golf 7/7.5 1.2T Si, 1.4T Si, 1.6TDi FWD 11/12>

Part Number: 28843-1

Front Lowering: 35mm
Rear Lowering: 35mm
Front Axle Weight: Up to 1010kg
Rear Axle Weight: Up to 940kg

H&R Lowering Springs - VW UP 11/11 and VW UP Facelift eUP (2016+)

Drop Front: 35mm
Drop Rear: 35mm

H&R Lowering Springs - Audi S3 8V/8V.5 Sportback & Sedan - Quattro

H&R Lowering Springs - Audi Q5 Quattro 8R (2009 - 2017) - Lowers F/R: 40/40mm

H&R Lowering Springs - Golf MK8 GTI Lowering Levels: Front 40mm Rear 40mm Enhance the look of your vehicle with H&R Lowering Springs. H&R Sport Springs provide a lower center of gravity and reduce body roll for better handling. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. If you are only looking to improve one part of your vehicle's suspension, you cannot go wrong with installing sport springs. Fun to drive, H&R Sport Springs are the number one upgrade for your vehicle. Sporty look and performance Progressive spring characteristics Less weight by using high tension steel TUV approved

At CTS Turbo we are proud to announce our new air intake system for the MK5 R32. The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our high quality silicones fit seamlessly with the OEM MAF flange allowing for smooth entry of cold air into the the engine providing peak power gains ranging from 9-15HP. All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

DESCRIPTION CTS Turbo is pleased to release our high flow turbo outlet pipe for 7-speed DSG MQB vehicles such a MK7.5 VW GTI, MK7.5 VW Golf R, MK7 VW GLI and 8V.2 Audi S3. The factory turbo outlet pipe is constructed from flimsy plastic and is quite narrow, which results in an extreme airflow restriction. The CTS Turbo high flow turbo outlet pipe kit is constructed from mandrel-bent 60mm aluminum tubing. A custom 5-ply silicon coupler makes installation simple! The CTS Turbo high flow turbo outlet pipe kit also replaces all the factory charge piping between the turbocharger compressor housing and factory intercooler. Product Details: 60mm aluminum piping with CTS logo 5-ply silicon coupler Factory mounting points are used for perfect fitment Durable black powdercoat finish For 7-speed DSG/S-tronic transmissions only Compatible with factory and upgraded turbos Compatible with factory and upgraded intakes Compatible with factory and upgraded intercoolers Parts Included: Upper turbo outlet silicon Lower turbo outlet pipe 2 clamps Installation hardware Fitment: 2018+ VW Golf R DSG 7-speed 2019+ VW GLI DSG 7-speed 2019+ VW GTI DSG 7-speed 2018+ Audi A3 S-Tronic 7-speed 2018+ Audi S3 S-Tronic 7-speed 2018+ Audi TT, TT-S S-Tronic 7-speed NOT COMPATIBLE WITH 6-SPEED DSG, AUTOMATIC or MANUAL TRANSMISSION MODELS, SEE CTS-IT-275