Not many enthusiasts are aware that OE and more importantly aftermarket sway bar effectiveness can be hindered by worn or inadequate mounts, drop links and lateral stoppers.
Not many enthusiasts are aware that OE and more importantly aftermarket sway bar effectiveness can be hindered by worn or inadequate mounts, drop links and lateral stoppers.
Whiteline offset strut tops allow for extra negative camber and positive caster to improve steering response, steering feel and reduced movement to ensure wheel alignment stability through a high quality spherical bearing. Perfect for the high performance street or track day weapon, providing improved tyre life and extra grip during high speed / high load cornering.
Product Details
The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation.
Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle!
You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device.
In house designed and built in the USA, our Boost Tap includes the following:
Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap
3 Vacuum Ports with 1/4" Hose Barb Fittings
3 Vacuum Set Screws
Medium Strength Thread Lock
OEM Securing Clip
Manifold Pierce Alignment Tools
In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!
The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team for the EA888 TSI vehicles, the Forge turbo blanket is designed to assist in the protection and prolonged life of the engine components.
The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it shouldnot be routinely removed as you will likely damage the blanket.
Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers:
T4
T5
T25
The Garrett GTX28 and GTX30 Range
Borg Warner EFR6258
Interior Surface:
· Max Temperature Rating: 2300°F/1260°C · Continuous Use Limit: 1832°F1000°C
Exterior Surface:
· Direct Contact Limit: 1800°F/982°C · Radiant Heat Limit: 2500°F/1371°C
This will replace OEM part numbers 06H 145 710D, 06F 145 710G, & 06H 145 710 C
Forge Motorsport is proud to release the latest version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CJXB, CZPA, and CJXC;US codes CPLA and CPPA) including Golf MK7 R
This valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. It has also been proven in cars running over 600bhp!
This new valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.
We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner
In The Box: 1 x FMDVMK7R Valve 1 x Wiring Harness 1 x Solenoid, Bracket, and Screws 1 x Uprated Blue Spring 10 x Cable Ties 1 x 1000mm of 4mm Vacuum Tube 1 x 5mm T Piece 1 x Instructions 1 x Forge Keyring and Sticker
• New control box and updated screen bargraph • Updated harness with streamlined connectors • New improved color coded obd2 harness • Read D.T.C's on command • Remove unwanted PIDs / gauge modes • Configure units individually for English/Metric • Calibrate vehicle speed reading • Read AFR in Lambda (vehicles with wideband) • Auto-detect available PIDs / sensors • Pre-configured analog inputs for P3 Sensors
The P3 Analog Gauge*This gauge IS NOT plug and play. Boost/vacuum hose to the engine is required and wiring needs to be completed for power, ground, and optional analog inputs.
4 Available Analog Readouts
Analog boost (yellow/purple/black - dedicated plug for analog boost sensor) *boost tap not included
Analog input 1 (brown wire - can read any 0-5 volt linear output sensor)
Analog input 2 (blue wire - can read any 0-5 volt linear output sensor)
Battery voltage (red wire / black wire - read through power and ground wires)
optional auto-dim feature (green wire - connect to any circuit that gets power only when the headlamps are on and enable feature in the configuration menu for the display to auto-dim when the headlamps are on)
OEM Vent Option
We install the display in an OEM vent for your vehicle to make your install even easier.
Analog gauge base kit includes
Integrated display
Analog Box control unit
Main harness
Hard-wire harness
Analog boost sensor *boost tap not included
Approximately 5' of 5/32" O.D. boost tubing with 5/32" I.D. hose at each end