H&R Lowering Springs - Audi Q3

H&R Lowering Springs - VW Polo GTI

H&R 35MM LOWERING SUSPENSION SPRINGS

Golf 7/7.5 1.2T Si, 1.4T Si, 1.6TDi FWD 11/12>

Part Number: 28843-1

Front Lowering: 35mm
Rear Lowering: 35mm
Front Axle Weight: Up to 1010kg
Rear Axle Weight: Up to 940kg

H&R Lowering Springs - VW UP 11/11 and VW UP Facelift eUP (2016+)

Drop Front: 35mm
Drop Rear: 35mm

H&R Lowering Springs - Audi S3 8V/8V.5 Sportback & Sedan - Quattro

H&R Lowering Springs - Audi Q5 Quattro 8R (2009 - 2017) - Lowers F/R: 40/40mm

H&R Lowering Springs - Golf MK8 GTI Lowering Levels: Front 40mm Rear 40mm Enhance the look of your vehicle with H&R Lowering Springs. H&R Sport Springs provide a lower center of gravity and reduce body roll for better handling. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. If you are only looking to improve one part of your vehicle's suspension, you cannot go wrong with installing sport springs. Fun to drive, H&R Sport Springs are the number one upgrade for your vehicle. Sporty look and performance Progressive spring characteristics Less weight by using high tension steel TUV approved

V3 2019 Release

P3 OBD2 Multi-Gauge

• Plug and Play install - just plug into your obd2 port and install into dash!
• Reads and clears OBD2 Codes
• OBD2 Data for Coolant Temp, Intake Air Temp, Exhaust Gas Temp, Throttle Plate, Vehicle Speed, RPM, Shift-light, Battery voltage, 0-60 timer and more!
• Peak Recall on all functions
• Boost and Vacuum from OBD2 port
• Optional 80psi analog boost sensor
• Optional Auto-Dim or Manual Dimmer
• 2 x universal 0-5v linear analog inputs
• Includes digital display, custom OBD2 wire harness and control box.

 

P3 Cars - V3 2019 Release

NEW FEATURES

• New control box and updated screen bargraph
• Updated harness with streamlined connectors
• New improved color coded obd2 harness
• Read D.T.C's on command
• Remove unwanted PIDs / gauge modes
• Configure units individually for English/Metric
• Calibrate vehicle speed reading
• Read AFR in Lambda (vehicles with wideband)
• Auto-detect available PIDs / sensors
• Pre-configured analog inputs for P3 Sensors

The P3 Analog Gauge *This gauge IS NOT plug and play. Boost/vacuum hose to the engine is required and wiring needs to be completed for power, ground, and optional analog inputs.

4 Available Analog Readouts 

• Analog boost (yellow/purple/black - dedicated plug for analog boost sensor) *boost tap not included
• Analog input 1 (brown wire - can read any 0-5 volt linear output sensor)
• Analog input 2 (blue wire - can read any 0-5 volt linear output sensor)
• Battery voltage (red wire / black wire - read through power and ground wires)

• optional auto-dim feature (green wire - connect to any circuit that gets power only when the headlamps are on and enable feature in the configuration menu for the display to auto-dim when the headlamps are on)

OEM Vent Option

• We install the display in an OEM vent for your vehicle to make your install even easier.

Analog gauge base kit includes

• Integrated display
• Analog Box control unit
• Main harness
• Hard-wire harness
• Analog boost sensor *boost tap not included
• Approximately 5' of 5/32" O.D. boost tubing with 5/32" I.D. hose at each end
• 3 zip ties
• 2 scotchlok wire taps

 Questions? Check out our P3 Analog Gauge install/config page for details.

Front Lowering: 35mm
Rear Lowering: 35mm
Front Axle Weight: Up to 1100kg
Rear Axle Weight: Up to 1090kg

Sporty looks and performance
Progressive spring characteristics
Less weight by using high tension steel
TUV approved