Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

 

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

Description

DESCRIPTION
CTS Turbo is proud to release our 1.8T and 2.0T Atmospheric BOV KIT for EA888.3 equipped vehicles. The CTS Turbo Atmospheric BOV KIT (EA888.3) is made of billet construction and completely serviceable. Our kit is designed to work with all of the factory electronics, will not cause any check engine lights and is plug and play with no wiring extensions required. The CTS Turbo Atmospheric BOV KIT (EA888.3) replaces the factory plastic unit which has been prone to failure from torn diaphragms, cracked plastic, and electrical malfunctions. Our piston design ensures long life, easy installation, complete serviceability, great sound and great value. This valve is quite compact being slightly shorter than the stock unit and fits nicely even in the tight engine bays of today’s VAG cars.

Fitment:

MK7 Golf R (EA888 Gen 3)
MK7 Golf GTI (EA888 Gen 3)
MK7 Golf 1.8 TSI (EA888 Gen 3)
MKIII Audi S3 (EA888 Gen 3)
MKIII Audi A3 (EA888 Gen 3)
MK2 Audi TT (EA888 Gen 3)
Skoda Octavia VRS (EA888 Gen 3)
MKVI+ Jetta 1.8T and 2.0T (EA888 Gen 3)
MKII Beetle (EA888 Gen 3)
Passat B7 (EA888 Gen 3)

Product Features:
T6061 billet aluminum construction
Black anodized stealth finish
Fully compatible with OE electronics
Fully serviceable piston design
No additional wiring required
Substantial reliability improvement over OE
Compact design fits into tight spots easily

Eibach PRO-KIT Performance Springs World‘s leading Performance Suspension Spring System

Eibach PRO-KIT Performance Springs World‘s leading Performance Suspension Spring System

H&R LOWERING SPRINGS SUITS AUDI Q3 8U 2011 - (F - 40MM / R - 50MM)

Autotech is the premier manufacturer of fuel pump upgrades for the FSI engine because our kit offers the highest quality, solid engineering, and great value.

Our HPFP Kit can achieve flow rates 50% higher than the original pump, essentially removing pump limitations from the equation, even on high-end turbo upgrades.

Our HPFP kit continues to be the benchmark that imitators strive to reach. However, Autotech’s HPFP Kit is not easily duplicated.

There are many reasons why Autotech’s Kit is superior. Here are a few:

~Each piston (9.8mm) and cylinder in Autotech HPFP kit undergo high-precision grinding processes many times during their manufacture, ensuring that the most precise tolerances are maintained through the final step. Not the cheapest way to make them, but the best way.

~Each piston and cylinder are match-ground and serialized to ensure absolute precision and the utmost longevity.

~Autotech was the first to incorporate plasma DLC coating on HPFP components to reduce friction losses and increase performance. Others have tried to follow by adding a coating to their parts. However, the DLC process alone is not enough – it is not a cure for substandard precision – the parts must be engineered specifically for the process to take full advantage: Autotech’s are. The success we have in the field can attest to that.

~HPFP-specific mapping is now commonly available from tuners worldwide.

Tuners trust Autotech’s HPFP in their conversions and upgrades because it works, and works well.

Fits VW/Audi 2.0T FSI 2006-2008.5, MK6 Golf R.

2 kits required for V8 4.2L FSI Audi B7 RS4 / R8 V8 / B8 S5 models.

1 kit required: TT RS 2.5L / RS3 Sportback 2.5L / B8 S4 3.0T / SQ5 Q7 3.0T / A6 A7 A8 3.0T / Touareg 3.0T / B8.5 S5 3.0T/ B8 A4 2.0T / B8.5 A4 2.0T 2 kits required: Audi 4.0T, 5.0T TFSI Audi R8 V10 / Lamborghini Gallardo / C6 Audi RS6 / 4.0T Audi S6, S7, RS6, RS7, S8 Also fits Audi Audi 09-14 2.0T B8 A4 A5 A6 Q5 TT 2.0T Autotech is the premier manufacturer of fuel pump upgrades for the FSI engine because our kit offers the highest quality, solid engineering, and great value. Upon installing the pump, notable increases include 5% Torque increase and an additional 10Bar of fuel rail pressure. Our HPFP kit continues to be the benchmark that imitators strive to reach. However, Autotech’s HPFP Kit is not easily duplicated. There are many reasons why Autotech’s Kit is superior. Here are a few: ~Each piston and cylinder in Autotech HPFP kit undergo high-precision grinding processes many times during their manufacture, ensuring that the most precise tolerances are maintained through the final step. Not the cheapest way to make them, but the best way. ~Each piston and cylinder are match-ground and serialized to ensure absolute precision and the utmost longevity. ~Autotech was the first to incorporate plasma DLC coating on HPFP components to reduce friction losses and increase performance. Others have tried to follow by adding a coating to their parts. However, the DLC process alone is not enough – it is not a cure for substandard precision – the parts must be engineered specifically for the process to take full advantage: Autotech’s are. The success we have in the field can attest to that. ~HPFP-specific mapping is now commonly available from tuners worldwide. Tuners trust Autotech’s HPFP in their conversions and upgrades because it works, and works well.

Eibach PRO-KIT Performance Springs World‘s leading Performance Suspension Spring System