SHIFT FASTER, DRIVE FASTER
The IE DSG Tune for your Audi B8/B8.5 S4/S5 3.0T delivers increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control and additional transmission performance features when paired with a matching ECU tune. Acceleration times will greatly improve turning your tuned 3.0T into a fully rounded performance monster.
LEADING FEATURES
Lightning fast gear shifts
Higher shift points of 7200 RPM
Multiple launch RPMs: 3400, 3600, 3800, 4000
Drive shift mapping entirely reworked with an enthusiast in mind
Flashed directly through OBD-II Port (No TCU removal required)
Works flawlessly with all IE ECU Tunes
Unlimited launches (factory defaults to 200)
Increased clutch pressure on tap for higher torque without slip
Temperature protection remains for safety
Gear hunting reduced
Gearbox “Torque Limiters” removed
WHAT DOES A DSG TRANSMISSION TUNE DO?
IE’s Audi S4 (DL501 S-Tronic) DSG tune is all-inclusive and does not offer expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features and upgrades are included at one low cost. A great deal of sportiness is added to the tune while maintaining factory smoothness and driveability that you love about the S4. More aggressive launches and faster shifts are guaranteed to put a smile on your face. Also, expect acceleration and 0-60 times to improve dramatically from a larger useable powerband provided by the higher shift points.
REQUIRED FOR SELECT ECU TUNES
Required for S4 & S5 Stage 2 dual pulley files, your new transmission tune will no longer lug the engine in drive mode or short shift the larger powerband. Clutch clamping forces are increased so the transmission can safely handle and deliver the increased power and torque. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes.
ONE TUNE FOR ALL STAGES
IE’s DSG tunes are all-inclusive without any expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset for any level of hardware or ECU Tune Stage, one cost and you are covered for all and any future upgrades from Stage 1 to Stage 2 billion.
USER ADJUSTABLE LAUNCH CONTROL
The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup!
Available Launch Control RPMs:
3400 RPM
3600 RPM
3800 RPM
4000 RPM
*Some early model B8 DSG TCUs cannot have launch control added to them, as well as some replacement Mechatronics units. Non compatible TCU codes include, but may not be limited to 8K1927156AC and 8K1927156AD. You can use your IE Powerlink tool to check your TCU code. Other DSG tune features will function normally.
IE DSG TUNE TECHNICAL FEATURES
HIGHER SHIFT POINTS
Utilize the whole powerband of your supercharged 3.0T engine without the DSG interfering and shifting early.
DRIVE MAPPING REWORKED
The B8 and B8.5 S4 is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode.
INCREASED CLUTCH PRESSURE
Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive.
FLASHED THROUGH OBD-II PORT
There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes.
TAKE-OFF LAG REDUCED
The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop.
MULTIPLE LAUNCH RPMS
The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup!
FLAWLESS OPERATION WITH IE ECU TUNES
The IE DSG Tune and ECU Tunes were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 3.0T engine and transmission. Perfect for all IE Tunes from Stage 1 to dual pulley and throttle upgrades.
VEHICLE FITMENT
Audi - S4 2008-2016 (B8 & B8.5) 3.0T supercharged engines*
Audi - S5 Coupe 2013-2016 (B8.5) 3.0T*
Audi - S5 Cabriolet 2009-2016 (B8-B8.5) 3.0T*
*IE DSG tunes are available only for vehicles equipped with Audi's 7-speed S-Tronic transmissions. Does not function with manual 6-speed transmission cars.
Already have an IE 3.0T intake? This highly stylized gloss carbon fiber lid is an optional upgrade that will completely transform your engine bay with a high-end performance finish. Specially designed to not only fit the IE CAI, but to also conform to the factory engine bay for a 100% perfect fit.
Sealed heatshield - Separates cold air from engine bay heat
Perfect fitment - No modifications required to bolt-on
Amazing sound - Releases awesome turbo and engine noise
Looks great - Black powder coat, tight clearances, clean angles
AUDI B8 A4 & A5 COLD AIR INTAKE
You're not just building a run of the mill bolt-on car with cheap imported parts. No, your Audi B8 A4 or A5 project deserves true performance designed mods and the best cold air intake available. This is not your average filter on a stick, IE engineers used specialized computer flow analysis software coupled with 3D scans of the engine bay to maximize performance. The result is a unique intake shape that optimizes flow and reduces air restrictions for an unmatched bump in power. Factory-like mounting solutions are used for a perfect fit and long life. Your new intake will fit like it was there stock, but perform and sound like a true motorsport intake design.
This is not another mass produced "filter on a stick". IE's cold air intake has been specifically engineered and developed using professional racing design aspects and specialized computational flow dynamic software. The result is a true Motorsport intake system that sounds and performs for the track with a sophisticated and classy design.
EASY POWER
The ram air design, built-in velocity stack, and our massive 5-inch filter inlet help deliver the most HP possible from a cold intake system. Expect peak gains of 15-20+HP/TQ on tuned engines.
DESIGN FEATURES
INCREASED AIR FLOW
Upgrading your ECU tune, pulleys, and other power adders requires airflow beyond that of the factory intake box. IE's intake feeds an impressive flow of air from the front of the vehicle directly to your supercharger. More cold air flow means more power, especially during the hot summer months. Ditch your stock restrictive airbox for the IE intake System. -Oh, and it sounds AWESOME too!
HIGH-FLOW VELOCITY STACK
Delivering cold air effectively for power takes more than just an open filter. Employing velocity stack technology like that found in professional Motorpsorts and adapting it for the 3.0T engine, efficiently channels air as quickly as possible. The velocity also functions as a solid mount for the air filter which means no intake pipes rattling or rubbing on heat shields.
PRECISION FIT
This Intake fits Audi 8R SQ5 & Q5 3.0T V6 Supercharged engines without any modification or installation hassles. The install process is simple and can be done quickly with basic tools. The fact that IE intake utilizes the factory airbox mounts ensures a perfect and hassle-free fit. Additionally, the stock mounts allow for engine movement which keeps intake components from getting damaged.
QUALITY COMPONENTS
IE uses a multi-piece heat shield which performs and looks great. It effectively channels cold air from the front of the car to the massive performance filter. Furthermore, it eliminates the induction of hot air found in other locations of the engine bay further protecting against power robbing heat off the exhaust and supercharger.
The IE MK6 Golf R Cold Air Intake Kit is the perfect intake upgrade for your engine bay. Benefits include added horsepower and torque, perfect MAF scaling, improved throttle response, and increased turbo noise. Peak gains are generally 10 Horsepower and Torque.
The massive 5” velocity stack and ram-air designed IE Cold Air Intake Kit delivers the most air and horsepower possible. Quickly add horsepower, torque, and aggressive engine and turbo sound to your VW or Audi 2.0T TSI (Gen1/2) engine.
LEADING FEATURES
INCREASED HORSEPOWER & TORQUE
ENHANCED ENGINE, TURBO, & BLOW-OFF SOUND
HIGH-FLOW BELLMOUTH
MASSIVE OVER-SIZED AIR FILTER
BLACK POWDER COAT FINISH
EASY INSTALL WITH NO MODIFICATIONS
USES FACTORY MOUNTING GROMMETS & HARDWARE
HEAT SHIELDING & DIRECTED AIR FLOW
REINFORCED SILICONE HOSES
FITS DSG AND MANUAL TRANSMISSIONS
YOUR BUILD DESERVES THE BEST
Feed your 2.0T TSI GTI, Jetta, GLI, CC, or A3 with a supply of cold air with this direct-fit high-flow cold air intake kit. This intake features a generously-sized inlet pipe that connects to the OE mass air flow (MAF) sensor. The MAF sensor receives high-velocity air fed directly from a 5" bellmouth. Our high-flow bellmouth is neatly housed in a heat shield, which separates the air filter from the hot under-hood air, allowing only cold air to be drawn into the turbo inlet directly from the front of the car.
STOCK-LIKE DIRECT FIT
This air intake kit provides all the necessary piping and couplers to plumb the intake system from the turbo to the MAF and then to the heat shield. The heat shield installs using the OE grommets for easy maintenance and reliable mounting with no rubbing or interference with other factory parts.
HIGH-FLOW VELOCITY STACK
The air intake utilizes a high-flow bellmouth behind the air filter to deliver as much air as possible. This bellmouth design increases the air velocity to the MAF and pulls cold air equally from all directions into the filter. This bellmouth is securely fastened to the heat shield as a clean pass-through providing a solid mount for the air filter and turbo inlet pipe. You have no worry about the intake pipe moving around and causing damage unlike other intake kits on the market, which simply clamp the filter onto the end of the inlet pipe or MAF. Furthermore, the bellmouth opening allows for a filter with a very large surface area that can support any horsepower goal. The same filter and bellmouth design have been tested to support over 500HP!
THERMAL BLOCKING HEAT SHIELD
The IE heat shield is designed to create a thermal barrier blocking all of the radiant heat from the engine bay. Only cold air from the front of the vehicle is drawn into the filter from the opening in the radiator support keeping air intake temperatures as cold as possible. This allows factory placement of the intake to be used without placing the filter lower in the vehicle where it can be subjected to engine harming road debris or fluid.
DO YOU NEED AN SAI KIT?
The MK5/MK6 2.0T TSI engine has two different engine codes. CBFA engine codes are equipped from the factory with a secondary air injection (SAI) pump that connects to the factory intake box. These engines require a small breather filter for this SAI line when installing an aftermarket intake. CCTA engine codes do not have this SAI pump and will not require this filter. Identify your engine code using the photos below, and add an SAI filter kit above if needed when ordering your intake.
EASY INSTALLATION
Installation is quick and easy to install with basic tools. The process should take around an hour for most enthusiasts.
Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. Does not work with the DV+ Diverter Valve or Diverter Valve spacers.
TURBO INLET PIPE FEATURES
Greatly improves air-flow to turbocharger
Constant high-flow inner diameter
Easy install, no modifications necessary
Long life cast aluminum alloy
In-house CNC machined for perfect fitment
No leak o ring seal to turbocharger
Outflows stock inlet by 110CFM
IS YOUR STOCK INLET ROBBING POWER?
The factory installed plastic turbo inlet found installed on your VW or Audi Gen 3 1.8T or 2.0T TSI engine is adequate enough for stock cars with factory hardware and ECU calibrations. However, the necked down design becomes a major flow restriction when ran with power upgrades such as cold air intakes, intercoolers, downpipes, and ECU upgrades.
UPGRADE YOUR TURBO INLET PIPE
The IE Turbo Inlet Pipe helps you to get the most out of your IS38 or IS20 turbo and power upgrades by removing the factory flow restriction. The cast aluminum design allows for a constant diameter elbow increasing efficiency from the intake to the turbo without the bottleneck design of the factory unit.
HORSEPOWER RESULTS
Dyno graph tested on a 2019 GTI with Stage 2 hardware & software on 93 octane
EASY INSTALLATION
Your new turbo inlet pipe has been in-house CNC machined and includes all required hardware to allow for a perfect and easy installation. View and download the install guide here (coming soon).
REQUIRES AFTERMARKET INTAKE
Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. Does not work with the DV+ Diverter Valve or Diverter Valve spacers.
The IE Audi B9 A4 & A5 2.0T Cold Air Intake is the perfect addition to any engine bay. Give your Audi added horsepower, torque, snappier throttle response, and an aggressive sound. Typical peak gains from our CAI are roughly 10-20 Horsepower and Torque.
POWER GAINS
The ram air design, velocity stack, and massive 55-inchfilter inlet help deliver the most HP possible from a cold intake system.
Expect peak gains of 10-20+HP/TQ on tuned engines.
INCLUDED IN THE B9 IE CAI KIT
IE Intake velocity stack & heatshield assembly
IE Silicone turbo inlet pipe assembly
IE 5” inlet performance air filter
IE Turbo heat shield
All necessary hardware (clamps, nuts, bolts, etc)
INCREASED AIR FLOW
This Intake delivers an impressive flow increase to feed your turbo. More cold air flow means more power; especially during the hot summer months. Ditch your stock restrictive airbox for the IE intake System.
DESIGN DETAILS
IE engineers set out to produce the highest performing cold air intake that looks great and fits like a factory installed part in your A4. The latest in computer design and 3D scanning technology were employed during the development process for a perfect fit and maximum performance. The final product resulted in the greatest performing and best-looking intake available.
HIGH-FLOW VELOCITY STACK
Delivering cold air to your engine is a must for making power. The velocity stack efficiently channels air as quickly as possible into the intake system. The velocity also functions as a solid mount for the air filter which means no intake pipes rattling on heat shields.
CUSTOM HEAT SHIELD
IE uses a three piece heat shield which performs and looks great. It effectively channels cold air from the front of the car to the massive performance filter. Furthermore, it eliminates the induction of hot air found in other locations of the engine bay. A second heat shield is mounted above the turbocharger to further protect against power robbing heat off the exhaust and turbo.
PERFECT FITMENT
This Intake fits B9 Audi A4 and A5 without any modification or installation hassles. The install process is simple and can be done quickly with basic tools. The fact that IE intake utilizes the factory airbox mounts ensures a perfect and hassle free fit. Additionally, the stock rubber mounts allow for engine movement which keeps intake components from getting damaged.
CLASSY AND CLEAN APPEARANCE
Wrinkle black powder coated velocity stack and heat shields result in a sleek and sporty appearance in any engine bay. As a final touch, all IE heat shields are finished with a classy, laser etched, stainless steel IE logo badge.
The following power result data was collected on our in-house Dynapack hub dyno. Dyno chart is as tested at 4500 feet altitude with SAE corrected numbers. Before and after results are direct back-to-back comparisons on a full bolt-on stage 2 B9 A4 2.0T engine. The only change made to the vehicle between testing is the swap from a stock intake with a new clean air filter to the IE Cold Air Intake Kit. Dyno power results are approximate and may vary from car to car.
HORSEPOWER & TORQUE DYNO CHART
HORSEPOWER & TORQUE POWER GAINS OVER STOCK
VEHICLE FITMENT
Audi - A4 2015+ (B9) 2.0T
Audi - A5 2015+ (B9) 2.0T
Audi - A4 Allroad 2015+ (B9) 2.0T
This intake does not fit cars that have a MAF housing/sensor.