Vehicles

Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

 

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

The Mk5/Mk6 ConsolePod™ holds two (2) 2” or 2 1/16” (52mm) gauges and mounts on underside of the center console. Made with a low-gloss finish, the ConsolePod is uniquely designed to allow you to use the storage compartment 12V power socket and angles the gauges upward towards the driver. The ConsolePod can be used for both LHD and RHD cars and comes with split loom tubing to cover and protect the gauge wires.

Mandrel bent aluminum piping with durable black powder coating - CNC machined MAP flange - 4 Ply silicon connectors with stainless steel clamps - Integrated water methanol bung with plug - Stainless steel clamps

CTS Turbo is proud to announce an official release of our new K04 Upgrade for 2.0T FSI/TSI Transverse Engines. Our engineers designed the compressor cover and exhaust housing to work with the larger K04 CHRA, exactly how intended. While other manufacturers simply install a larger K04 CHRA into a small factory-spec housing. Beware of these hybrid builds, they are not made to provide optimal flow for the larger turbine wheel and can lead to poor performance and premature failure. High-quality castings are CNC machined to replace your factory turbocharger and do not require any additional parts to be installed. All you need to run this K04 2.0T FSI/TSI Transverse Turbocharger Upgrade is a tune for your ECU and a performance downpipe. This kit is by far the best ‘bang for the buck’ modification available for VW and Audi enthusiasts with the 2.0T FSI and 2.0T TSI engine. With proper tuning and supporting mods, this turbo will support 350HP/360TQ! Features: CTS-spec K04 CHRA with heavy-duty thrust bearings Billet compressor wheel (MFS – machined from solid) K04-specific compressor and turbine housing. NOT A HYBRID! OEM+ manufacturing tolerances VSR high-speed balanced Direct-fit factory replacement OEM installation kit included Compatible with any K04-specific tune Compatible with factory turbo outlet pipe (both FSI and TSI). Not compatible with aftermarket stock turbo outlet pipes ROW vehicles, please confirm fitment with your CTS Turbo dealer. Additional parts required: K04-specific software tuning CTS Turbo or other performance downpipe Additional parts recommended: CTS Turbo Cold Air Intake CTS Turbo Direct-Fit Intercooler Kit CTS Turbo High Flow Turbo Outlet Pipe (EA888 only) S3 Fuel Injectors and HPFP upgrade (EA113 engines only)

CTS Turbo Blankets isolate the heat produced by your IHI IS12/IS20/IS38 turbocharger with the purpose of reducing turbo lag, cooler air intake temperatures, protecting and prolonging engine components, and giving a boost in horsepower.  In keeping the heat of the exhaust gases contained within the hot side of the turbocharger and away from the cool side of the turbocharger and the intake path, more oxygen per unit volume reaches the engine, and thus, more power.

This turbo blanket fits all IHI turbos found on MQB platform cars

IS12 Turbos found on MK7 1.8TSI Golf and 8V Audi A3 FWD

IS20 Turbos found on MK7 GTI and 8V Audi A3 Quattro

IS38 Turbos found on the MK7 Golf R and 8V Audi S3

CTS Turbo Blanket Heat Tolerance:

Interior Surface:
Max Temperature Rating: 2100 Deg F
Continuous Use Limit: 1800 Deg F

Exterior Surface:
Direct Contact Limit: 800 Deg F
Radiant Heat Limit: 1200 Deg F

Now fully compatible with all 2018-2020 Audi RS3/TTRS 2.5T DAZA and DNWA engines, this is one kit to fit them all!

CTS Turbo is proud to announce our improved 8V, 8V.2/8S Audi RS3/TTRS Throttle Body Inlet Kit for DAZA and DNWA

Our high flow throttle body inlet is designed it to be larger, but also more aerodynamic than the stock part. Our inlet has a 56% internal volume increase over the stock inlet. Using the latest CAD software, the shape of the inlet tract was flow optimized and cast from aluminum for best performance. All critical parts were CNC machined to ensure perfect fitment and performance.

We have also included our machined throttle body spacer from with two additional ports for boost reference and methanol injection; as well and a high-flow 2.75″ throttle inlet pipe. Custom-made silicone couplers and t-bolt clamps allow for seamless, easy installation.

Features:

• CAD optimized for maximum flow, 56% larger than factory
• Cast aluminum throttle body elbow, billet aluminum spacer
• CNC machined in house for perfect fitment
• Direct replacement for factory parts between the cold side of the intercooler and the throttle body
• HP gain of up to 20hp on stock turbo, even more with big turbo upgrades
• Compatible with factory intake, CTS Turbo intakes and most other popular intakes (not compatible with Eventuri intake)
• Compatible with factory and aftermarket intercoolers
• Includes a large-bore 2.75″ charge pipe and custom silicone couplers
• Two extra 1/8″ NPT bungs on the charge pipe for watermeth nozzles
• Compatible with 1-bolt and 2-bolt pressure sensors
• DV flange is based on factory design
• Includes hoses and fittings to install on 2019+ DNWA engines

Fitment:

• 8V and 8V.2 Audi RS3 (2018-2020) – DAZA and DNWA models
• 8S Audi TT-RS (2018-2020) – DAZA and DNWA models