Vehicles - IPE - New South Performance - Genuine VW - P3 Cars - Vogtland - VW Central
P3 Cars - V3 2019 Release
NEW FEATURES
• New control box and updated screen bargraph
• Updated harness with streamlined connectors
• New improved color coded obd2 harness
• Read D.T.C's on command
• Remove unwanted PIDs / gauge modes
• Configure units individually for English/Metric
• Calibrate vehicle speed reading
• Read AFR in Lambda (vehicles with wideband)
• Auto-detect available PIDs / sensors
• Pre-configured analog inputs for P3 Sensors
The P3 Analog Gauge *This gauge IS NOT plug and play. Boost/vacuum hose to the engine is required and wiring needs to be completed for power, ground, and optional analog inputs.
*Available for both pre and post facelift vehicles*
4 Available Analog Readouts
- Analog boost (yellow/purple/black - dedicated plug for analog boost sensor) *boost tap not included
- Analog input 1 (brown wire - can read any 0-5 volt linear output sensor)
- Analog input 2 (blue wire - can read any 0-5 volt linear output sensor)
- Battery voltage (red wire / black wire - read through power and ground wires)
- optional auto-dim feature (green wire - connect to any circuit that gets power only when the headlamps are on and enable feature in the configuration menu for the display to auto-dim when the headlamps are on)
Analog gauge base kit includes
- Integrated display
- Analog Box control unit
- Main harness
- Hard-wire harness
- Analog boost sensor *boost tap not included
- Approximately 5' of 5/32" O.D. boost tubing with 5/32" I.D. hose at each end
- 3 zip ties
- 2 scotchlok wire taps
Sale
The Mk5/Mk6 ConsolePod™ holds two (2) 2” or 2 1/16” (52mm) gauges and mounts on underside of the center console.
Made with a low-gloss finish, the ConsolePod is uniquely designed to allow you to use the storage compartment 12V power socket and angles the gauges upward towards the driver.
The ConsolePod can be used for both LHD and RHD cars and comes with split loom tubing to cover and protect the gauge wires.
Regular Price:
$75.00
Special Price
$45.00
Product Details
The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation.
Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle!
You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device.
In house designed and built in the USA, our Boost Tap includes the following:
Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap
3 Vacuum Ports with 1/4" Hose Barb Fittings
3 Vacuum Set Screws
Medium Strength Thread Lock
OEM Securing Clip
Manifold Pierce Alignment Tools
In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!
Sale
For drivers side vent of RHD 2015 GTI or Golf.Not for Jetta
Regular Price:
$127.00
Special Price
$62.00
Sale
Mounting on top of the steering column, the WRX/STI ColumnPod™ is designed to hold a 2” or 2 1/16” (52mm) gauge on your Impreza WRX/STI (2008-2014) or Forester (2009-2013)
The unique design offsets the gauge to the left for maximum visibility of the dash instrumentation.
Molded from ABS and matched in color and gloss, the ColumnPod™ looks like an OEM installation. It holds the gauge at an angle that minimizes distractions and helps keep your eyes on the road.
Our exclusive design hides all wires and tubes from view.
Regular Price:
$94.00
Special Price
$59.00
Sale
Regular Price:
$275.00
Special Price
$255.00