Audi - CTS Turbo - Turbosmart - Integrated Engineering - SuperPro - Flow Designs

Now fully compatible with all 2018-2020 Audi RS3/TTRS 2.5T DAZA and DNWA engines, this is one kit to fit them all!

CTS Turbo is proud to announce our improved 8V, 8V.2/8S Audi RS3/TTRS Throttle Body Inlet Kit for DAZA and DNWA

Our high flow throttle body inlet is designed it to be larger, but also more aerodynamic than the stock part. Our inlet has a 56% internal volume increase over the stock inlet. Using the latest CAD software, the shape of the inlet tract was flow optimized and cast from aluminum for best performance. All critical parts were CNC machined to ensure perfect fitment and performance.

We have also included our machined throttle body spacer from with two additional ports for boost reference and methanol injection; as well and a high-flow 2.75″ throttle inlet pipe. Custom-made silicone couplers and t-bolt clamps allow for seamless, easy installation.

Features:

• CAD optimized for maximum flow, 56% larger than factory
• Cast aluminum throttle body elbow, billet aluminum spacer
• CNC machined in house for perfect fitment
• Direct replacement for factory parts between the cold side of the intercooler and the throttle body
• HP gain of up to 20hp on stock turbo, even more with big turbo upgrades
• Compatible with factory intake, CTS Turbo intakes and most other popular intakes (not compatible with Eventuri intake)
• Compatible with factory and aftermarket intercoolers
• Includes a large-bore 2.75″ charge pipe and custom silicone couplers
• Two extra 1/8″ NPT bungs on the charge pipe for watermeth nozzles
• Compatible with 1-bolt and 2-bolt pressure sensors
• DV flange is based on factory design
• Includes hoses and fittings to install on 2019+ DNWA engines

Fitment:

• 8V and 8V.2 Audi RS3 (2018-2020) – DAZA and DNWA models
• 8S Audi TT-RS (2018-2020) – DAZA and DNWA models

Designed to maximise the benefit of Roll Control Adjustable Sway Bars and be used in place of that hard to find O.E link.

• Ball for low friction and long life
• Elminate sway bar flex for consistent handling
• Spanner provision for on-car adjustment
• Suitable for application on lowered or raised vehicles

The CTS Runner Flap Delete allows for the removal of the restrictive intake flappers from the factory intake manifold. The factory intake flappers can be a substantial restriction in modified vehicles, the CTS RFD is a must for any FSI owner that wants to minimize airflow restrictions and maximize power to the ground.

Mandrel bent aluminum piping with black powder coating - CNC machined MAP flange - DV relocation/noise pipe bung - 4 Ply silicon connectors with stainless steel clamps - Integrated water methanol bung with plug - Stainless steel clamps

MK5 MY09 onwards MK6 R/GTI/Golf/Jetta/GLI 8J Audi A3/TT 8P Audi A3/TT

For EA888.1 Gen 1 TSI models (2009-2013) - Mandrel bent aluminum piping with black powder coating - CNC machined MAP flange - DV relocation/noise pipe bung - 4 Ply silicon connectors with stainless steel clamps - Integrated water methanol bung with plug - Stainless steel clamps

Audi - S1 EA888 Gen 3 - 2.0 TFSI Audi - A3 & S3 (MK3) - EA888 Gen 3 - 1.8 TFSI and 2.0 TFSI Audi - A4 / Allroad (B8 & B8.5) - EA888 Gen 2 & 3 - 2.0 TFSI Audi - A5 (B8 & B8.5) - EA888 Gen 2 & 3 - 2.0 TFSI Audi - A6 (C6 & C7) - EA888 Gen 2 - 2.0 TFSI Audi - Q5 - EA888 Gen 2 & 3 - 2.0 TFSI Audi - TT / TTS (MK3) - EA888 Gen 3 - and 2.0 TFSI VW - Golf / GTI / R (MK7) - EA888 Gen 3 - 1.8 TSI and 2.0 TSI

The CTS Turbo TSI Turbo Outlet Pipe (TOP) is designed to replace the narrow 'pancake' pipe that comes as factory equipment on your vehicle. Our Turbo Outlet Pipe features 2.25" diameter aluminum tube for optimized flow. The CNC machined billet mating flange makes connecting this TOP to your FMIC literally a snap. The billet anodized turbo to TOP connector, 2.25" coupler and premium clamps top this package off. If you're looking for a simple bolt on modification that will optimize flow and increase power, then this part is for you.

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!

PRODUCT DETAILS

IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.

MACHINED DESIGN

Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.

FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY

This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.

PRODUCT FEATURES

 

• Replaces factory plastic valve cover
• Uses factory valve cover gasket
• In-house CNC machined from aluminum
• Includes o ring sealed matching billet oil cap
• -10AN breather outlet for catch can setups

ADDITIONAL PARTS REQUIRED

 

EVAP CROSSOVER TUBE RELOCATION KIT

The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11

CATCH CAN KIT FOR BILLET VALVE COVER

The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3

 

VEHICLE FITMENT

• Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
• Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
• Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
• Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
• VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
• VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
• VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
• VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*

*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.