Audi

P3 Cars - V3 2019 Release

NEW FEATURES

• New control box and updated screen bargraph
• Updated harness with streamlined connectors
• New improved color coded obd2 harness
• Read D.T.C's on command
• Remove unwanted PIDs / gauge modes
• Configure units individually for English/Metric
• Calibrate vehicle speed reading
• Read AFR in Lambda (vehicles with wideband)
• Auto-detect available PIDs / sensors
• Pre-configured analog inputs for P3 Sensors

The P3 Analog Gauge *This gauge IS NOT plug and play. Boost/vacuum hose to the engine is required and wiring needs to be completed for power, ground, and optional analog inputs.

*Available for both pre and post facelift vehicles*

4 Available Analog Readouts 

• Analog boost (yellow/purple/black - dedicated plug for analog boost sensor) *boost tap not included
• Analog input 1 (brown wire - can read any 0-5 volt linear output sensor)
• Analog input 2 (blue wire - can read any 0-5 volt linear output sensor)
• Battery voltage (red wire / black wire - read through power and ground wires)

• optional auto-dim feature (green wire - connect to any circuit that gets power only when the headlamps are on and enable feature in the configuration menu for the display to auto-dim when the headlamps are on)

Analog gauge base kit includes

• Integrated display
• Analog Box control unit
• Main harness
• Hard-wire harness
• Analog boost sensor *boost tap not included
• Approximately 5' of 5/32" O.D. boost tubing with 5/32" I.D. hose at each end
• 3 zip ties
• 2 scotchlok wire taps

 Questions? Check out our P3 Analog Gauge install/config page for details.

Front Lowering: 35mm
Rear Lowering: 35mm
Front Axle Weight: Up to 1100kg
Rear Axle Weight: Up to 1090kg

Sporty looks and performance
Progressive spring characteristics
Less weight by using high tension steel
TUV approved

Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!

PRODUCT DETAILS

IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.

MACHINED DESIGN

Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.

FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY

This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.

PRODUCT FEATURES

• Replaces factory plastic valve cover
• Uses factory valve cover gasket
• In-house CNC machined from aluminum
• Includes o ring sealed matching billet oil cap
• -10AN breather outlet for catch can setups

ADDITIONAL PARTS REQUIRED

EVAP CROSSOVER TUBE RELOCATION KIT

The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11

CATCH CAN KIT FOR BILLET VALVE COVER

The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3

VEHICLE FITMENT

• Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
• Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
• Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
• Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
• VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
• VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
• VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
• VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*

*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.

Description

We are proud to release the new our CTS Turbo Stage 3.5 Fuel Pump Kit for MQB GTI, MK7 Golf R, and B9 A4/A5.  As you may already know the TFSI fueling system has two separate fuel pumps, the LPFP (Low-Pressure Fuel Pump) and HPFP (High-Pressure Fuel Pump).  While there are a number of options for HPFP available, including the Autotech HPFP, there are limited options for fortifying the low-pressure fuel system.  CTS has developed a fully integrated fueling system, which utilizes a Walbro 525LPH E85 compatible in-tank fuel pump that is capable of supporting in excess of 600HP.  If you’re looking for a fuel pump system to support all the power that your engine can handle look no further than the CTS Turbo Stage 3.5 Fuel Pump Kit for MQB GTI, Golf R, 8V Audi A3/S3 and MQL B9 A4/A5.

NB: please keep in mind that some modifications to your fuel pump basket is required. Some baskets differ from each other so installation should be performed by an experienced technician.

Torqbyte Controller is an optional add-on and strongly recommended when using E85 fuel and tuning.

Product Details:

– Genuine Walbro High Output in-tank 525LPH HELLCAT E85 compatible Fuel Pump
– Genuine Walbro Filter sock (may not fit all revision fuel pump baskets)
– CTS CNC machined/black hard anodized pump adapter
– CTS CNC machined/black fuel pump spacers
– CTS CNC machined/black fuel pump venturi standoff
– Viton O-ring
– Nylon wire crimps
– Drill bits
– Stainless steel fasteners

Fitment:

• 2015 – current VW Golf (incl Sportwagen and AllTrack)
• 2015 – current VW GTI (incl Rabbit)
• 2015 – current VW Golf R
• 2015 – current Audi A3
• 2015 – current Audi S3
• 2017 – current Audi A4/A5/AllRoad

The following VW fuel pumps are compatible: 5Q0919051BK, 5Q0919051BM

DETAILS

Our adjustable front lip splitters extensions will bolt directly onto our RS3 8V Sedan FL front lip splitters thanks to the pre-pressed in threaded brass fittings on our front lip splitter. Fitting kit is provided to ensure perfect fitment and can be adjusted to your liking. Adjustments can be made anywhere between 5mm-20mm on each side increasing the overall width up to 40mm!

Front Lip Splitter and front winglets sold separately.

KIT INCLUDES:

• RS3 8V Sedan FL Front Lip Splitter Extensions (Pair)
• 2 Flow Designs stickers
• Fitting kit

MATERIAL & FINISH:

• 4.5mm thick ABS plastic
• Scratch resistant textured ABS plastic