Audi - CTS Turbo - Forge Motorsports - Turbosmart - Supernova

Kompact VAG V2 Plumb Back has been specifically to suit the 2.0L VAG engine Unlike the standard, plastic valves that use un-reinforced diaphragms and are known to crack under increased boost, the new Kompact VAG V2 Plumb Back uses O-Ring sealed piston which, coupled with it's billet aluminium construction give it over 30PSI boost handling capability. Included with each Kompact VAG V2 Plumb Back kit: Model specific valve, Mounting screws and Spring clamps.

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

• Distinctive vent-to-atmostphre BOV sound
• Suitable for stock or lightly modified vehicles
• Supplied blanking plug gives the option of converting to a full recirculating or full vent-to-atmosphere valve
• Eliminates compressor surge, even in stock applications

At CTS Turbo we are proud to announce our new air intake system for the Audi 3.0T and 3.2L FSI engines.  The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system.  Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing.  Our single piece CNC mandrel bent aluminum intake pipe allows for smooth entry of cold air into the the engine providing peak power gains ranging from 5-8HP.  All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.
 

Only for B8 and B8.5 Audi S4/S5/Q5/SQ5 with 3.0T or 3.2L V6 engine!

Product Details:
- Mandrel bent aluminum piping with black powder coating
- Reusable air filter with inverted cone design
- 4 Ply silicon connector with stainless steel clamps
- Sealed air box with rubberized trim
- Bracketry to prevent rattling under engine torquing
- Billet SAI breather adapter and Billet bracket with SAI breather filter
- Gains ranging from 5-8HP

Installation guide can be downloaded here

CTS Turbo is proud to announce our new intake system for the B9 AUDI A4, AllRoad, A5, S4, S5, RS4, RS5 (2017-2019 models)

We designed our system to work in conjunction with the OEM air scoop to seamlessly force cold air into the air intake system. Air then flows through our high flow 6″ velocity stack air filter for maximum engine performance.

Our single-piece proprietary moulded silicone couplers allows for smooth entry of air into the engine providing peak power gains ranging from 10-12HP on a stock car.
All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound. Turbo spool up and diverter valve release are a lot louder!

Features:

• Massive 6″ velocity stack filter, largest on the market
• 3.5″ silicone turbo inlet hoses for both 4-cylinder and 6-cylinder engines (5-ply construction, will not collapse)
• Heatshield to keep air temperatures as low as possible
• Easy install and perfect fitment
• Increased engine performance, less turbo lag
• Sporty sound under acceleration and loud pressure release
• Gains of 10-12HP on stock vehicles, tuned cars will gain even more!
• Kit comes with parts to install on 1.8T, 2.0T, 2.9T and 3.0T engines (fits MAF-LESS cars)

Fitment:

• B9 A4 (2017 – current)
• B9 AllRoad (2017 – current)
• B9 S4 (2018 – current)
• B9 A5 (2018 – current)
• B9 S5 (2018 – current)
• B9 RS4 (2018 – current)
• B9 RS5 (2018 – current)

Does not fit cars with MAF sensor.

Installation Guide S4

Installation Guide A4

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

Forge Motorsport were the OG’s of this original groundbreaking design, and we still lead the marketplace with customer service and after care with this innovative blow off valve - Often copied never bettered

This is our piston version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CHHC, CZPA, CJXB and CJXC;US codes CPLA and CPPA)  including Golf MK7 R. This valve is a full replacement atmospheric blow-off valve (i.e. noisy) that integrates seamlessly with the OEM electronics and results in no detriment in performance, and absolutely NO fault codes or check engine lights, which isn’t something that can be said of our competition!

Not only do you get the famous Forge blow off valve sound but this valve also increases the throttle response during gear changes by reducing turbo lag. It has been designed to help the turbocharger maintain its rotational speed ready for when you accelerate, whilst also taking the strain away from the impeller. Without removing this stress from your turbo, it could cause premature failure, especially on tuned engines and modified vehicles.

Like our full replacement recirculating valve option, this valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning-fast response. It has also been proven in cars running over 600bhp!

This valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.

⭐ Great product! Fits perfect and sounds beautiful! 10/10 ⭐

⭐  Fitted the blow of valve today! Works and sounds perfect, not to mention the great customer service to make sure I ordered the correct one ⭐

⭐  Easy installation and sounds fantastic! Money well spent ⭐

In The Box:
1 x FMDVMK7A Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker

Description

DESCRIPTION
CTS Turbo is proud to release our 1.8T and 2.0T Atmospheric BOV KIT for EA888.3 equipped vehicles. The CTS Turbo Atmospheric BOV KIT (EA888.3) is made of billet construction and completely serviceable. Our kit is designed to work with all of the factory electronics, will not cause any check engine lights and is plug and play with no wiring extensions required. The CTS Turbo Atmospheric BOV KIT (EA888.3) replaces the factory plastic unit which has been prone to failure from torn diaphragms, cracked plastic, and electrical malfunctions. Our piston design ensures long life, easy installation, complete serviceability, great sound and great value. This valve is quite compact being slightly shorter than the stock unit and fits nicely even in the tight engine bays of today’s VAG cars.

Fitment:

MK7 Golf R (EA888 Gen 3)
MK7 Golf GTI (EA888 Gen 3)
MK7 Golf 1.8 TSI (EA888 Gen 3)
MKIII Audi S3 (EA888 Gen 3)
MKIII Audi A3 (EA888 Gen 3)
MK2 Audi TT (EA888 Gen 3)
Skoda Octavia VRS (EA888 Gen 3)
MKVI+ Jetta 1.8T and 2.0T (EA888 Gen 3)
MKII Beetle (EA888 Gen 3)
Passat B7 (EA888 Gen 3)

Product Features:
T6061 billet aluminum construction
Black anodized stealth finish
Fully compatible with OE electronics
Fully serviceable piston design
No additional wiring required
Substantial reliability improvement over OE
Compact design fits into tight spots easily

At CTS Turbo we are proud to announce our new air intake system for the 2.5T EVO MK3 TTRS & 8V.2 RS3 (facelift) 2018 model year.

The OEM air scoop works in conjunction with our airbox to seamlessly force cold air into our air intake system.  Air then flows through our high flow cone air filter, which utilizes an inverted cone design and 4″ Velocity stack for maximum engine breathing.  Our single-piece CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 6-11HP.  All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.

The coupler included is only compatible with the factory turbo inlet pipe. 4″ coupler for CTS Turbo inlet pipe is available separately.

Product Details:

• Mandrel-bent aluminum piping with black powder coating
• Reusable air filter with an inverted cone design
• 4″ composite velocity stack equipped intake
• 4 Ply silicon connectors with stainless steel clamps
• Ram air style airbox with rubberized trim
• Bracketry to prevent rattling under engine torquing
• Gains ranging from 6-11HP on a stock vehicle

Fitment:

• 2018 Audi RS3 2.5T EVO (EA855)
• 2018 Audi TTRS 2.5T EVO (EA855)