Audi - CTS Turbo - Forge Motorsports - Turbosmart - VW Central

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

Kompact VAG V2 Plumb Back has been specifically to suit the 2.0L VAG engine Unlike the standard, plastic valves that use un-reinforced diaphragms and are known to crack under increased boost, the new Kompact VAG V2 Plumb Back uses O-Ring sealed piston which, coupled with it's billet aluminium construction give it over 30PSI boost handling capability. Included with each Kompact VAG V2 Plumb Back kit: Model specific valve, Mounting screws and Spring clamps.

At CTS Turbo we are proud to announce our new air intake system for the Audi 3.0T and 3.2L FSI engines.  The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system.  Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing.  Our single piece CNC mandrel bent aluminum intake pipe allows for smooth entry of cold air into the the engine providing peak power gains ranging from 5-8HP.  All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.
 

Only for B8 and B8.5 Audi S4/S5/Q5/SQ5 with 3.0T or 3.2L V6 engine!

Product Details:
- Mandrel bent aluminum piping with black powder coating
- Reusable air filter with inverted cone design
- 4 Ply silicon connector with stainless steel clamps
- Sealed air box with rubberized trim
- Bracketry to prevent rattling under engine torquing
- Billet SAI breather adapter and Billet bracket with SAI breather filter
- Gains ranging from 5-8HP

Installation guide can be downloaded here

• Distinctive vent-to-atmostphre BOV sound
• Suitable for stock or lightly modified vehicles
• Supplied blanking plug gives the option of converting to a full recirculating or full vent-to-atmosphere valve
• Eliminates compressor surge, even in stock applications

CTS Turbo is proud to announce our new intake system for the B9 AUDI A4, AllRoad, A5, S4, S5, RS4, RS5 (2017-2019 models)

We designed our system to work in conjunction with the OEM air scoop to seamlessly force cold air into the air intake system. Air then flows through our high flow 6″ velocity stack air filter for maximum engine performance.

Our single-piece proprietary moulded silicone couplers allows for smooth entry of air into the engine providing peak power gains ranging from 10-12HP on a stock car.
All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound. Turbo spool up and diverter valve release are a lot louder!

Features:

• Massive 6″ velocity stack filter, largest on the market
• 3.5″ silicone turbo inlet hoses for both 4-cylinder and 6-cylinder engines (5-ply construction, will not collapse)
• Heatshield to keep air temperatures as low as possible
• Easy install and perfect fitment
• Increased engine performance, less turbo lag
• Sporty sound under acceleration and loud pressure release
• Gains of 10-12HP on stock vehicles, tuned cars will gain even more!
• Kit comes with parts to install on 1.8T, 2.0T, 2.9T and 3.0T engines (fits MAF-LESS cars)

Fitment:

• B9 A4 (2017 – current)
• B9 AllRoad (2017 – current)
• B9 S4 (2018 – current)
• B9 A5 (2018 – current)
• B9 S5 (2018 – current)
• B9 RS4 (2018 – current)
• B9 RS5 (2018 – current)

Does not fit cars with MAF sensor.

Installation Guide S4

Installation Guide A4

At CTS Turbo we are proud to announce our new air intake system for the 2.5T EVO MK3 TTRS & 8V.2 RS3 (facelift) 2018 model year.

The OEM air scoop works in conjunction with our airbox to seamlessly force cold air into our air intake system.  Air then flows through our high flow cone air filter, which utilizes an inverted cone design and 4″ Velocity stack for maximum engine breathing.  Our single-piece CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 6-11HP.  All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.

The coupler included is only compatible with the factory turbo inlet pipe. 4″ coupler for CTS Turbo inlet pipe is available separately.

Product Details:

• Mandrel-bent aluminum piping with black powder coating
• Reusable air filter with an inverted cone design
• 4″ composite velocity stack equipped intake
• 4 Ply silicon connectors with stainless steel clamps
• Ram air style airbox with rubberized trim
• Bracketry to prevent rattling under engine torquing
• Gains ranging from 6-11HP on a stock vehicle

Fitment:

• 2018 Audi RS3 2.5T EVO (EA855)
• 2018 Audi TTRS 2.5T EVO (EA855)

At CTS Turbo we are proud to announce our new air intake system for the VW MK7 & MK7.5 Golf/GTI, MK7 & MK7.5 Golf R and facelift Audi A3/S3 is ready! This is the largest intake available, and it is excellent for tuned vehicles that require the extra air flow. 

The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system.  Air then flows through our 3.5" high flow air filter, which utilizes an inverted cone design for maximum engine breathing.  Our 3.5" CNC mandrel bent aluminum intake pipe allows for smooth entry of cold air directly into the the engine, minimizing turbulence from unnecessary connections. All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.

Peak power gains range from 10-15HP on an otherwise stock vehicle. We recommend disabling your Soundaktor (noise amplifier) to fully enjoy the true sound of your motor and remove excessive drone caused by the device.

Product Details:

• Mandrel bent large bore 3.5" aluminum piping with black powder coating
• Coveted Laser etched //CTS Turbo logo
• 3.5" Reusable air filter with inverted cone design
• 4 Ply silicon connectors with stainless steel clamps
• Sealed air box
• Bracketry to prevent rattling under engine torquing
• Billet SAI breather adapter and filter (Optional in drop down menu)

• 2014+ VW Golf (all models)
• 2014+ VW GTI 
• 2014+ VW Golf R
• 2018+ Audi A3 (all models)
• 2018+ Audi S3

 NOTE: If you have a Golf, GTI or A3 you will require the SAI breather adapter and filter. Only for vehicles WITHOUT a MAF sensor.

CONFIRM ON YOUR CAR BEFORE ORDERING!

This is a tool to remove and install the driveshaft on 2017+ 8V Audi RS3 & 8S Audi TTRS.

Use this tool to safely and effectively remove or install the driveshaft (prop shaft) in your 2017+ Audi RS3 or TT-RS. 

• Heavy duty steel construction
• Made in Canada
• Threaded to be used with most available slide-hammers (not required) 
• Based on Audi factory tool
• Easy to use, save time when working on your car
• Required when removing or installing downpipe on RS3/TT-RS
• For vehicles with slip-fit driveshaft

CTS Turbo is proud to announce our high flow turbo inlet for B9 Audi S4/S5/SQ5

The biggest issue with the restrictive factory inlet is apparent when you start to increase the power. Our engineers designed the turbo inlet to be as large as possible; yet still fit perfectly. This was accomplished using the latest in 3D scanning and rapid prototyping technology.

The larger inlet will provide increased flow to the turbo and make sure the engine has all the air that it needs to operate at maximum capacity!

Features:

• High flow cast aluminum turbo inlet pipe
• Precision machined fitment for the factory turbo
• Factory-style PCV connections
• Developed, tested and machined in-house
• Includes new o-ring and allen head bolts for easy install

Fitment:

• 2018-on Audi B9 S4
• 2018-ont Audi B9 S5
• 2018-on Audi B9 SQ5