One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

Audi - A3 & S3 (8V & 8S) - EA888 Gen 3 - 1.8 TFSI and 2.0 TFSI VW - Golf / GTI / R (MK7 & MK7.5) - EA888 Gen 3 - 1.8 TSI and 2.0 TSI

Efficient bar and plate construction - Direct bolt-in installation - 4-ply silicon hoses and billet adapter to turbo outlet pipe - High quality stainless steel clamps - Low pressure drop - Maintains factory mounting points - No trimming of bumper or crash supports - Rated for power levels in excess of 600HP - Core dimensions: 23.00 Length x 2.00" Tall x 16.5" Height - Cast aluminium end tanks with mounting points that are CAST into the end tank, NOT welded like inferior intercoolers

The CTS Turbo Golf R Turbo Outlet Pipe (TOP) is designed to replace the narrow 'pancake' pipe that comes as factory equipment on your vehicle.

Stop missing shifts and your friends will stop laughing at you.

Eliminate free-play and slop in your factory shifter bracket by replacing soft factory rubber bushings.

Keep your shifts crisp and smooth; and stay ahead of the pack!

Kit includes:

3 x shifter bracket bushings (upper and lower halfs)

This part fits the following transmissions:

MK3: 02A ONLY

MK4: 02J, 02M

MK5: 02Q

MK6: 02Q

MK7: 6MT

CTS TURBO 8V.2 RS3/ 8S TTRS 2.5T EVO TURBO OUTLET PIPE

SHIFT FASTER, DRIVE FASTER The IE DSG Tune for your Audi B8/B8.5 S4/S5 3.0T delivers increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control and additional transmission performance features when paired with a matching ECU tune. Acceleration times will greatly improve turning your tuned 3.0T into a fully rounded performance monster. LEADING FEATURES Lightning fast gear shifts Higher shift points of 7200 RPM Multiple launch RPMs: 3400, 3600, 3800, 4000 Drive shift mapping entirely reworked with an enthusiast in mind Flashed directly through OBD-II Port (No TCU removal required) Works flawlessly with all IE ECU Tunes Unlimited launches (factory defaults to 200) Increased clutch pressure on tap for higher torque without slip Temperature protection remains for safety Gear hunting reduced Gearbox “Torque Limiters” removed WHAT DOES A DSG TRANSMISSION TUNE DO? IE’s Audi S4 (DL501 S-Tronic) DSG tune is all-inclusive and does not offer expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features and upgrades are included at one low cost. A great deal of sportiness is added to the tune while maintaining factory smoothness and driveability that you love about the S4. More aggressive launches and faster shifts are guaranteed to put a smile on your face. Also, expect acceleration and 0-60 times to improve dramatically from a larger useable powerband provided by the higher shift points. REQUIRED FOR SELECT ECU TUNES Required for S4 & S5 Stage 2 dual pulley files, your new transmission tune will no longer lug the engine in drive mode or short shift the larger powerband. Clutch clamping forces are increased so the transmission can safely handle and deliver the increased power and torque. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes. ONE TUNE FOR ALL STAGES IE’s DSG tunes are all-inclusive without any expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset for any level of hardware or ECU Tune Stage, one cost and you are covered for all and any future upgrades from Stage 1 to Stage 2 billion. USER ADJUSTABLE LAUNCH CONTROL The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! Available Launch Control RPMs: 3400 RPM 3600 RPM 3800 RPM 4000 RPM *Some early model B8 DSG TCUs cannot have launch control added to them, as well as some replacement Mechatronics units. Non compatible TCU codes include, but may not be limited to 8K1927156AC and 8K1927156AD. You can use your IE Powerlink tool to check your TCU code. Other DSG tune features will function normally. IE DSG TUNE TECHNICAL FEATURES HIGHER SHIFT POINTS Utilize the whole powerband of your supercharged 3.0T engine without the DSG interfering and shifting early. DRIVE MAPPING REWORKED The B8 and B8.5 S4 is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode. INCREASED CLUTCH PRESSURE Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive. FLASHED THROUGH OBD-II PORT There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes. TAKE-OFF LAG REDUCED The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop. MULTIPLE LAUNCH RPMS The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! FLAWLESS OPERATION WITH IE ECU TUNES The IE DSG Tune and ECU Tunes were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 3.0T engine and transmission. Perfect for all IE Tunes from Stage 1 to dual pulley and throttle upgrades. VEHICLE FITMENT Audi - S4 2008-2016 (B8 & B8.5) 3.0T supercharged engines* Audi - S5 Coupe 2013-2016 (B8.5) 3.0T* Audi - S5 Cabriolet 2009-2016 (B8-B8.5) 3.0T* *IE DSG tunes are available only for vehicles equipped with Audi's 7-speed S-Tronic transmissions. Does not function with manual 6-speed transmission cars.