Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

Kompact VAG V2 Plumb Back has been specifically to suit the 2.0L VAG engine Unlike the standard, plastic valves that use un-reinforced diaphragms and are known to crack under increased boost, the new Kompact VAG V2 Plumb Back uses O-Ring sealed piston which, coupled with it's billet aluminium construction give it over 30PSI boost handling capability. Included with each Kompact VAG V2 Plumb Back kit: Model specific valve, Mounting screws and Spring clamps.

Description:

Leyo Motorsport dual port boost tap system plugs directly into the intake manifold and makes several configuration options available. Makes anything for your boost reference, such as boost gauges, bov & etc. It will also maintain OEM PCV system function.

Specifications:

• Machined billet Aluminum T6061.

• Dual Port Design for multiple boost reference.

• Direct bolt on easy Installation.

• Dual leak free O-ring. 

• Distinctive vent-to-atmostphre BOV sound
• Suitable for stock or lightly modified vehicles
• Supplied blanking plug gives the option of converting to a full recirculating or full vent-to-atmosphere valve
• Eliminates compressor surge, even in stock applications

Description

• Stand out from the crowd.

• Dare to be different.

• Simple yet sophisticated look.

• Quick n Easy install.

• Stylishly elegant.

• Run out of things to mod.

• Cleaner than your ex-girlfriend.

• Adds 10HP to your key.

LEYO CLEAR KEY BASE

KEY TO THE FUTURE

OPEN

REMOVE

INSTALL

DONE

Product Description

This is a direct replacement for Part Number 06H 131 111. - It will fit EA888 Gen 3 engine with IHI Turbo IS20 IS38

On a 2.0L Porsche Macan, this muffler delete gave an additional 10bhp during dyno tests.

Forge has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (TSI) (EA888 engine). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.

Product Description

This will replace OEM part numbers 06H 145 710D, 06F 145 710G, & 06H 145 710 C

Forge Motorsport is proud to release the latest version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CJXB, CZPA, and CJXC;US codes CPLA and CPPA) including Golf MK7 R

This valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. It has also been proven in cars running over 600bhp!

This new valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

In The Box:
1 x FMDVMK7R Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

Forge Motorsport were the OG’s of this original groundbreaking design, and we still lead the marketplace with customer service and after care with this innovative blow off valve - Often copied never bettered

This is our piston version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CHHC, CZPA, CJXB and CJXC;US codes CPLA and CPPA)  including Golf MK7 R. This valve is a full replacement atmospheric blow-off valve (i.e. noisy) that integrates seamlessly with the OEM electronics and results in no detriment in performance, and absolutely NO fault codes or check engine lights, which isn’t something that can be said of our competition!

Not only do you get the famous Forge blow off valve sound but this valve also increases the throttle response during gear changes by reducing turbo lag. It has been designed to help the turbocharger maintain its rotational speed ready for when you accelerate, whilst also taking the strain away from the impeller. Without removing this stress from your turbo, it could cause premature failure, especially on tuned engines and modified vehicles.

Like our full replacement recirculating valve option, this valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning-fast response. It has also been proven in cars running over 600bhp!

This valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.

⭐ Great product! Fits perfect and sounds beautiful! 10/10 ⭐

⭐  Fitted the blow of valve today! Works and sounds perfect, not to mention the great customer service to make sure I ordered the correct one ⭐

⭐  Easy installation and sounds fantastic! Money well spent ⭐

In The Box:
1 x FMDVMK7A Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker