CTS Turbo is proud to offer our upgraded turbo inlet hose for the MK7+ VW and 8V Audi MQB vehicles. The factory turbo inlet hose is corrugated with internal ridges that disrupt air flow. Not only do they reduce air flow, but the plastic can become weak over time causing leaks and reduced performance.
The CTS Turbo turbo inlet hose is constructed from 5-ply silicone that will not collapse, even under heavy load. This is MUCH stronger than other inlet hoses offered by different companies. Collapsing intake hose can cause turbo to fail!!
The CTS Turbo inlet hose allows for smooth uninterrupted flow and more air pumping through your engine!
Features:
Components:
1 x CTS Turbo MQB Turbo Inlet Hose
2 x Hose clamps
Fits the following vehicles:
The CTS Runner Flap Delete allows for the removal of the restrictive intake flappers from the factory intake manifold. The factory intake flappers can be a substantial restriction in modified vehicles, the CTS RFD is a must for any FSI owner that wants to minimize airflow restrictions and maximize power to the ground.
Regular Price: $299.00
Special Price $279.00
Audi | TT | MK2 (2008-2015) | 2.0 TSI |
Audi | A3 | 8P (2009-2013) | 2.0 TSI (FWD) |
Volkswagen | Tiguan | (2009-2011) | 2.0 TSI |
Volkswagen | Tiguan | (2012+) | 2.0 TSI |
Volkswagen | Jetta | MK5 (2010) | 2.0 TSI |
Volkswagen | Jetta | MK6 Sedan (2011-2017) | 2.0T GLI |
Volkswagen | Jetta | MK6 Sportwagen (2010-2017) | 1.8TSI/2.0TSI |
Volkswagen
Volkswagen |
Jetta
Golf/GTI/Rabbit |
MK6 Sedan (2014-2017)
MK5 (2009) |
1.8TSI/2.0T GLI
2.0 TSI |
Volkswagen | Golf/GTI/Rabbit | MK6 (2010-2014) | 2.0T |
Volkswagen | CC | (2009+) | 2.0 TSI |
Volkswagen | Beetle | Beetle (2012+) | 2.0 TSI |
CTS Turbo is proud to release our B-Cool Billet Oil Filter Housing. The OE plastic filter housing is quite fragile and is know to become brittle and crack over time. Each CTS Turbo B-Cool Billet Oil Filter Housing is constructed in house from T6061 Aluminum. Not only does the B-Cool filter look good, but it works great. We have engineered cooling fins into our design to act as a heatsink, which dissipates heat from the engine oil.
Installation is very straight forward and only required basic hand tools:
Drain oil from filter housing, use a 36mm socket to remove the factory oil filter housing, install new filter, install new filter housing o-ring to CTS housing, reinstall on the car and tighted to 18 ft/lbs, refill engine oil.
Product Details:
The CTS B-Cool Billet fits Audi, VW, Seat, Skoda models with EA113 2.0T FSI engines, 2.5L 5-cylinder engines and 2.5T 5-cylinder turbo engines.
This part replaces the OE part# 06D 115 408B and 07K 115 408.
Fitment:
This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.
Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.
This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!
Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.
The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.
Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!
The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!
This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease!
It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.
The OEM part numbers we have replaced with our valve include:
Regular Price: $399.00
Special Price $359.00