Don't short shift your ECU tune and performance parts, get the most out of your modifications with the IE DSG Transmission tune for 2015+ Golf R, GTI, A3, & S3 2.0T. Instantly gain increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control, and a true performance tuned transmission. Acceleration times will greatly improve transforming your 2.0T into a fully rounded performance monster.
The IE DSG Tune for the MQB 2015-2017 Golf R / S3 and 2015-2018 GTI / A3 is expertly calibrated to deliver the full performance potential from your existing ECU tune and modifications. This transmission file retunes the complicated DSG mapping and completely reworks the shift points in drive, sport, and manual shifting. This delivers much, much faster and stronger shifts taking time directly off the 0-60 and ¼ mile times making the car more reliable and fun to drive.
Required for MQB Stage 1 high torque and all Stage 2 tune files, your new transmission tune will no longer lug the engine in drive mode, or short shift the larger powerband. Clutch clamping forces are increased so the transmission can safely handle and deliver the increased power and torque. To get the most out of your tune investment, a lot of features have been added to make a fully rounded performance vehicle with more aggressive launches, faster shifting, higher RPM, and optimized shift points, and selectable launch control. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes.
IE’s DSG tunes are all-inclusive without any expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset for any level of hardware or ECU Tune Stage, one cost and you are covered for all and any future upgrades.
The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup!
Available Launch Control RPMs:
HIGHER SHIFT POINTS
Utilize the whole powerband of your turbocharged VW or Audi engine without the DSG interfering and shifting early.
DRIVE MAPPING REWORKED
The MQB 2.0 TSI DSG is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode.
INCREASED CLUTCH PRESSURE
Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive.
FLASHED THROUGH OBD-II PORT
There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes.
TAKE-OFF LAG REDUCED
The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop.
MULTIPLE LAUNCH RPMS
The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup!
KICK DOWN REMOVED IN TIPTRONIC/MANUAL MODE
The kick down switch is disabled in manual shift mode, ensuring you stay in the gear you’ve selected, even during hard launches or over bumpy terrain
FLAWLESS OPERATION WITH IE ECU TUNES
The IE DSG Tune and ECU Tune were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 2.0 TSI Gen 3 engine and transmission.
Regular Price: $999.00
Special Price $950.00
Designed to maximise the benefit of Roll Control Adjustable Sway Bars and be used in place of that hard to find O.E link.
Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)
We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner
Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.
This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.
Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.
The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.
Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB
In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker
If you are unsure if this product is suitable for your application, please contact us.
Regular Price: $399.00
Special Price $339.00
One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.
Regular Price: $184.00
Special Price $179.00
Regular Price: $769.00
Special Price $692.00
Professional diagnostic tool in your pocket.
OBDeleven with 12 month PRO Plan OBDeleven becomes a professional diagnostic tool. Operating with easy to use application it allows to fully access all car systems, program, monitor and activate various functions via your iOS, Android, and Huawei devices.
Official and licensed full-featured software is constantly updated with new features. The programming temporarily is not supported on models that are manufactured from 2020 and have SFD protection. The negotiation regarding the support of these models is in progress.
Pack includes:
Frequently Asked Questions:
Q. What vehicles are supported with One-Click-Apps by OBDeleven
A. Please refer to OBDeleven Official Supported Vehicles Page
Q. Are OBDeleven credits included?
A. Yes, the Pro Pack includes 200 Credits with the kit, and provides you with 12 months access on their PRO Plan
Q. What vehicles are supported with this device?
A. Vehicles built after 1996 that are Audi, Volkswagen, Seat, Lamborghini, Bentley and Skoda models are supported.
Q. How do I know what tweaks or modifications I can code for my vehicle.
A. We do not provide support with the coding and adaptation, there are many YouTube guides for VCDS & OBDeleven:
Here is an example of some MK7 Coding and Adaptation available for your OBDeleven device
Q. Does this product require an internet connection?
A. Yes, an internet connection is required whilst using the OBDeleven device. We recommend having good reception and a strong signal to ensure a stable connection with their servers.
Q. If I require assistance with this product who do I contact?
A. OBDeleven have a dedicated support area
Q. Will any changes I do to my vehicle with OBDeleven have any effect on my factory vehicle warranty?
A. Any form of modification may impact your warranty. VW Central will not take any responsibility for damage caused by using the OBDeleven device.
Q. Where do I find the OBDeleven App?
A. The OBDeleven App is available on both the Apple App Store or for Android Users on the Google Play Store.
Features for iOS Devices:
Features for Android Devices:
Regular Price: $249.00
Special Price $209.00
Description:
Leyo Motorsport dual port boost tap system plugs directly into the intake manifold and makes several configuration options available. Makes anything for your boost reference, such as boost gauges, bov & etc. It will also maintain OEM PCV system function.
Specifications:
Machined billet Aluminum T6061.
Dual Port Design for multiple boost reference.
Direct bolt on easy Installation.
Dual leak free O-ring.
LEYO Cold Air Intake System for the Polo GTI (AW) guarantees greater air induction volume, colder intake air temperature and smoother air flow for superior power gain.
LEYO Cold Air Intake System was designed with the ultimate goal of maximum power gain. Made with high grade full aluminum 3’inch diameter ensuring greater, smoother air flow with minimal restrictions and effective heat dispersion. Factory MAF sensor part is used to prevent anomaly in MAF sensor reading.
LEYO R&D team also optioned for quality proven LEYO pod filter element for uncompromised filtration, performance and ease of maintenance. Specially designed airbox prevents heat soak, effectively extracting colder induction air. No fabrication required for installation, bolts straight onto factory mounting points.
Note:
-Only for petrol EA888.3b MQB cars, not for diesel cars.
-Only for vehicles with air flow sensor on factory intake.
-This product is only for use on the race track.
Specifications:
OEM fitment requires no fabrication.
3' inch diameter for greater air induction.
Unique quality and design.
Track and dyno proven for greater horsepower gain.
Heat shield included.
Direct bolt on & easy installation.
Easy installation.
Intake Heat shield.
Struggling with the OEM Turbo Valve? Need to add that unique boost pressure sound? Make sure to get your hands on All New Re-Designed Leyo Motorsports latest in-house designed Diverter Valve. Leyo Motorsport Diverter Valve multi piece design is built and engineered to solve the failure issues associated with the OEM solenoid valves and their diaphragm resulting in boost leaks. It is built from 6061 Billet Aluminum with hard coated Anodized finish with an internal serviceable piston based design that provides greater reliability over the OEM as well as quicker throttle and turbo response. All components are made in-house by Japan CNC’s, inspected to 0.01mm tolerance by Japan CMM, laser etched and race proven.
Leyo Motorsport Diverter vavle has a unique and fully tested internal piston compared with other brands in order to get the maximum results in power. We are offering a stronger, more durable and reliable valve compared to the OEM unit. We do have uprated valve spring in stock that is sold separately.
Specifications:
Made from the highest quality T6061 billet aluminium construction.
Direct OEM replacement..
Improved throttle response
Consistent turbo boost.
Reduced turbo lag .
Fully compatible with OE electronics.
Fully serviceable piston .
Holds up to 600HP. (with optional uprated spring kit)
* Note : This DV kit comes supplied with BLACK / WHITE / YELLOW Spring. Uprated BLUE / RED Spring is Available for purchase.
Struggling with the OEM Turbo Valve? Need to add that unique boost pressure sound? Make sure to get your hands on the All New Re-Designed Leyo Motorsports latest in-house designed Blow Off Valve. Leyo Motorsport Blow Off Valve's multi piece design is built and engineered to solve the failure issues associated with the OEM solenoid valves and their diaphragm resulting in boost leaks. It is built from 6061 Billet Aluminum with hard coated Anodized finish with an internal serviceable piston based design that provides greater reliability over the OEM as well as quicker throttle and turbo response. All components are made in-house by Japan CNC’s, inspected to 0.01mm tolerance by Japan CMM, laser etched and race proven.
Leyo Motorsport Blow Off Valve has a unique and fully tested internal piston compared with other brands in order to get the maximum results in power. We offer a stronger, more durable and reliable valve compared to the OEM unit. We do have uprated valve spring in stock that is sold separately.
Set yourself apart from the rest of the boosted crowd and get your vehicle the best automotive Blow Off Valve available at Leyo Motorsport.
Specifications:
Made from the highest quality T6061 billet aluminium construction.
Direct OEM replacement.
Improved throttle response.
Consistent turbo boost & Prevent boost leak.
Reduced turbo lag .
Fully compatible with OE electronics.
Fully serviceable piston .
Great sound.
Holds up to 600HP (with uprated spring kit) .