A3 - Turbosmart - H&R Springs - Leyo Motorsport - Integrated Engineering - T-carbon - P3 Cars - Eibach - INA - Autotech

The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.  

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

This recirculating catch can kit has been designed for use with the IE billet valve cover (IE part number: IEBAVC5) as a simple install solution for your billet valve cover and catch can. 
IE billet valve cover sold separately. 

 

Product Features

 

Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!

PRODUCT DETAILS

IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.

MACHINED DESIGN

Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.

FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY

This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.

PRODUCT FEATURES

 

• Replaces factory plastic valve cover
• Uses factory valve cover gasket
• In-house CNC machined from aluminum
• Includes o ring sealed matching billet oil cap
• -10AN breather outlet for catch can setups

ADDITIONAL PARTS REQUIRED

 

EVAP CROSSOVER TUBE RELOCATION KIT

The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11

CATCH CAN KIT FOR BILLET VALVE COVER

The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3

 

VEHICLE FITMENT

• Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
• Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
• Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
• Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
• VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
• VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
• VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
• VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*

*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.

VW has encountered a problem with the FSI camshaft and cam follower that could lead to damage to your engine's cylinder head.

This small part can play quite a big role in your engine's well-being. It conveys the movement of your camshaft into power for the high pressure fuel pump by riding directly on the camshaft lobe.

 If it becomes worn to the point of breaking it can cause permanent damage to the camshaft, fuel pump, or both. It could also send metal particles into your cylinder head which can cause damage to moving parts. Without replacement, it is common for followers to have holes worn through them.

Replacing this follower as a form of preventative maintenance can save you from spending even more money and time replacing your fuel pump or camshaft from damage caused by a worn follower.

H&R Sport Sway Bars are crafted from a special 50CRV4 steel alloy, the highest tensile strength available.

The quality of the material and design guarantees smooth transitional sway bar function, decreasing feedback response time and increasing stiffness over stock.

H&R Sport Sway Bars improve lateral stability and cornering grip, while reducing body roll. H&R Sport Sway Bars are designed for drivers who desire improved handling without lowering or affecting ride quality. H&R Sport Sway Bars increase stiffness and reduce body roll while maintaining comfort and increasing cornering control, lateral stability, and grip. 

A unique feature of H&R Sport Sway Bars are the smooth, machined-like forged ends that, for specific vehicles, allow for adjustability in stiffness.

Being 100% German made means a commitment to doing it right and giving you the best quality product.

Features:
- Reduces body roll
- Highest tensile strength available
- Works with DCC (adaptive suspension)

- Special urethane/Teflon composite bushes that are maintenance free

Swaybar Size:
- Front 24mm

- Rear 26mm

Adjustable:
- Front x2
- Rear x2

Compatibility:

• Audi A3 8P 2003-2012 4WD
• Audi S3 8P 2003-2012 4WD
• Skoda SUPERB 3T SEDAN 4WD
• Skoda OCTAVIA 1Z SEDAN + WAGON 4WD
• VW GOLF MK5 2003-2008 4WD
• VW GOLF MK6 2008-2012 4WD
• VW PASSAT B6/B7 2005-2014 4WD
• VW Tiguan 5N 2007-2015 4WD

Description:

Leyo Motorsport dual port boost tap system plugs directly into the intake manifold and makes several configuration options available. Makes anything for your boost reference, such as boost gauges, bov & etc. It will also maintain OEM PCV system function.

Specifications:

• Machined billet Aluminum T6061.

• Dual Port Design for multiple boost reference.

• Direct bolt on easy Installation.

• Dual leak free O-ring. 

H&R Lowering Springs - Audi Q3

The IE Catted Cast Downpipe for VW & Audi MQB incorporates the best of all worlds. Cast bend sections enable the highest flow and best fitment possible. Impressive performance gains will be realized when used with an IE stage 2 ECU tune. Lastly, the aggressive sound from an unrestricted exhaust system is guaranteed to be music to your ears. Product Features • Proven performance gains • 76mm (3 inch) tubing replaces restrictive 60mm factory tubing • Bolt on fitment - no hassle or poorly fitting parts when you choose IE • Constructed of 304 stainless piping - long-lasting and high-quality material • Thick turbo flange - prevents leaks and warping • High flow 200 cell catalytic converter - full power with reduced pollution and smell • Metal matrix catalytic structure - • OEM style flex section - allows for more adjustment and won’t fail • All inclusive kit - downpipe, mid pipes, all hardware • TIG welded construction - equates to long-lasting welds that are less likely to fail • Install instructions - available by CLICKING HERE MQB PERFORMANCE DOWNPIPE OVERVIEW When upgrading your VW MK7 or Audi 8V A3 to stage 2 software you will also need to reduce the back pressure caused by the small diameter stock pipe. With the exhaust system flowing better performance gains be achieved. Turbo lag should also be reduced as an added benefit. IE engineers guarantee a perfect fit by designing all IE downpipes in-house using the latest technology. Digital scanning is using to scan the entire environment which ensures that there is proper clearance and that all mounting points are in the correct location. Manufactured from 304 stainless offers a life-long product that brings performance and fun to the table for years to come. POWER GAINS The most power gains will be achieved when the IE Downpipe is paired with IE matching software, air intake, and FDS intercooler. SOUND TUNING An aggressive and drone-free sound will be emitted from the IE Cast Downpipe. This should be music to your ears! Thick wall tubing and cast sections remove much of “tinny” sound emitted by cheaper, thin wall, downpipes. With downpipes, you get what you pay for in terms of sounds and overall manufacturing quality. HIGH-FLOW CATALYTIC CONVERTER IE’s performance downpipe includes a high-flow 200 cell per inch metal matrix catalyst located as close to the turbo as possible. Metal matrix catalysts are higher performance because the matrix web is thinner, allowing higher flow in the same size. Our catalyst is also a very large diameter, allowing a large flow area and maximum power. By being placed close to the turbo, emissions and unwanted unpleasant smells are greatly reduced. DIRECT BOLT-ON WITH PERFECT FITMENT The IE downpipe replaces over 6 feet of restrictive factory exhaust tubing, all the way back to the OE “Cat-Back” rear section. Sturdy fabricated mounts and precise engineering result in a rattle free and long last replacement exhaust system. 3D scanning systems were employed to ensure perfect placement both in pre and post-production phases. INSTALLATION Installation should be completed by a professional and preferably on an auto lift. CLICK HERE to view and download the install guide. *This product is not CARB certified and thus is not available for purchase in the state of California. VEHICLE FITMENT Audi - A3 MK3/8V 1.8T & 2.0T engines (FWD only)* VW - GTI MK7 2.0T engine VW - GTI MK7.5 2.0T engine VW - Golf MK7 1.8T & 2.0T engine (FWD only)* VW - Golf MK7.5 1.8T & 2.0T engine (FWD only)* *This downpipe system includes a mid pipe that is specially designed to fit Gen 3 1.8T and 2.0T engines in front-wheel drive (FWD) vehicles only. All-wheel drive (AWD) Quattro, or 4 Motion vehicles require a different mid pipe section included in our AWD MQB downpipe kit IE Part Number: IEEXCI1. Please verify if your vehicle is AWD or FWD before ordering. ADDITIONAL REQUIRED MODIFICATIONS Installing a downpipe to your Gen 3 1.8T or 2.0T vehicle requires a matching stage 2 ECU tune to operate properly.