H&R Lowering Springs - VW MK6 Golf R

H&R Lowering Springs - VW MK7 & MK7.5 Golf VII R

H&R Lowering Springs - VW MK6 Golf GTI & GTD

H&R Lowering Springs - VW Polo GTI

H&R 35MM LOWERING SUSPENSION SPRINGS

Golf 7/7.5 1.2T Si, 1.4T Si, 1.6TDi FWD 11/12>

Part Number: 28843-1

Front Lowering: 35mm
Rear Lowering: 35mm
Front Axle Weight: Up to 1010kg
Rear Axle Weight: Up to 940kg

H&R Lowering Springs - Golf MK8 GTI Lowering Levels: Front 40mm Rear 40mm Enhance the look of your vehicle with H&R Lowering Springs. H&R Sport Springs provide a lower center of gravity and reduce body roll for better handling. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. If you are only looking to improve one part of your vehicle's suspension, you cannot go wrong with installing sport springs. Fun to drive, H&R Sport Springs are the number one upgrade for your vehicle. Sporty look and performance Progressive spring characteristics Less weight by using high tension steel TUV approved

Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

 

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

H&R Lowering Springs - VW Scirocco III incl. R

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

Product Description

This will replace OEM part numbers 06H 145 710D, 06F 145 710G, & 06H 145 710 C

Forge Motorsport is proud to release the latest version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CJXB, CZPA, and CJXC;US codes CPLA and CPPA) including Golf MK7 R

This valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. It has also been proven in cars running over 600bhp!

This new valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

In The Box:
1 x FMDVMK7R Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker