H&R Lowering Springs - VW MK6 Golf R

H&R Lowering Springs - VW MK7 & MK7.5 Golf VII R

H&R Lowering Springs - VW MK6 Golf GTI & GTD

H&R Lowering Springs - VW Polo GTI

H&R 35MM LOWERING SUSPENSION SPRINGS

Golf 7/7.5 1.2T Si, 1.4T Si, 1.6TDi FWD 11/12>

Part Number: 28843-1

Front Lowering: 35mm
Rear Lowering: 35mm
Front Axle Weight: Up to 1010kg
Rear Axle Weight: Up to 940kg

H&R Lowering Springs - Golf MK8 GTI Lowering Levels: Front 40mm Rear 40mm Enhance the look of your vehicle with H&R Lowering Springs. H&R Sport Springs provide a lower center of gravity and reduce body roll for better handling. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. If you are only looking to improve one part of your vehicle's suspension, you cannot go wrong with installing sport springs. Fun to drive, H&R Sport Springs are the number one upgrade for your vehicle. Sporty look and performance Progressive spring characteristics Less weight by using high tension steel TUV approved

DETAILS

The VW MK7 Golf R splitter set from Flow Designs includes a front splitter with Aerospacers, side splitters, rear spats & rear valance. Each item is precision made & hand polished - popular with many Volkswagen enthusiasts as our splitters are known for being impact resistant & extremely strong.

---

KIT INCLUDES

• MK7 Golf R rear aero valance
• MK7 Golf R rear pods/spats (pair)
• 2 Flow Designs stickers
• Fitting kit

MATERIAL

• 10mm thick polyethylene composite, bevelled edges

FINISH

• Hand polished satin black

H&R Lowering Springs - VW Scirocco III incl. R

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

Volkswagen Scirocco PFL/FL Side Splitters (Pair) Details: Finish the aero styling of your Scirocco street project with Flow Designs splitter set, complete with front & side splitters, rear spats & rear valance. The set fits facelift & prefacelift bumpers, with a guarantee of impact resistance on all splitters. Fast Australian & international delivery! Kit Includes: Side splitters (pair) to suit pre-facelift and facelift Scirocco R 2 Flow Designs stickers Fitting kit Material: 10mm thick polyethylene composite, bevelled edges Finish: Hand polished satin black Why do we use Polyethylene Composite for Flow Designs Splitters? Strong, impact resistant, doesn't corrode or chip, and has excellent abrasion resistance (say… from scraping on driveways and road all the time?) Carbon Fibre is better isn’t it? As strong and light as Carbon fibre is, it CRACKS on impact or when under load and/or stress. Clear coat will eventually fades & cracks and become undesirable.