Volkswagen - Forge Motorsports - IPE - Integrated Engineering - VW Central

The IE MK6 Golf R Cold Air Intake Kit is the perfect intake upgrade for your engine bay. Benefits include added horsepower and torque, perfect MAF scaling, improved throttle response, and increased turbo noise. Peak gains are generally 10 Horsepower and Torque.

ADD POWER, TORQUE, AND SOUND

The massive 5” velocity stack and ram-air designed IE Cold Air Intake Kit delivers the most air and horsepower possible. Quickly add horsepower, torque, and aggressive engine and turbo sound to your VW or Audi 2.0T TSI (Gen1/2) engine. 

LEADING FEATURES

• INCREASED HORSEPOWER & TORQUE
• ENHANCED ENGINE, TURBO, & BLOW-OFF SOUND
• HIGH-FLOW BELLMOUTH
• MASSIVE OVER-SIZED AIR FILTER
• BLACK POWDER COAT FINISH
• EASY INSTALL WITH NO MODIFICATIONS
• USES FACTORY MOUNTING GROMMETS & HARDWARE
• HEAT SHIELDING & DIRECTED AIR FLOW
• REINFORCED SILICONE HOSES
• FITS DSG AND MANUAL TRANSMISSIONS

YOUR BUILD DESERVES THE BEST

Feed your 2.0T TSI GTI, Jetta, GLI, CC, or A3 with a supply of cold air with this direct-fit high-flow cold air intake kit. This intake features a generously-sized inlet pipe that connects to the OE mass air flow (MAF) sensor. The MAF sensor receives high-velocity air fed directly from a 5" bellmouth. Our high-flow bellmouth is neatly housed in a heat shield, which separates the air filter from the hot under-hood air, allowing only cold air to be drawn into the turbo inlet directly from the front of the car.

STOCK-LIKE DIRECT FIT

This air intake kit provides all the necessary piping and couplers to plumb the intake system from the turbo to the MAF and then to the heat shield. The heat shield installs using the OE grommets for easy maintenance and reliable mounting with no rubbing or interference with other factory parts.

HIGH-FLOW VELOCITY STACK

The air intake utilizes a high-flow bellmouth behind the air filter to deliver as much air as possible. This bellmouth design increases the air velocity to the MAF and pulls cold air equally from all directions into the filter. This bellmouth is securely fastened to the heat shield as a clean pass-through providing a solid mount for the air filter and turbo inlet pipe. You have no worry about the intake pipe moving around and causing damage unlike other intake kits on the market, which simply clamp the filter onto the end of the inlet pipe or MAF. Furthermore, the bellmouth opening allows for a filter with a very large surface area that can support any horsepower goal. The same filter and bellmouth design have been tested to support over 500HP!

THERMAL BLOCKING HEAT SHIELD

The IE heat shield is designed to create a thermal barrier blocking all of the radiant heat from the engine bay. Only cold air from the front of the vehicle is drawn into the filter from the opening in the radiator support keeping air intake temperatures as cold as possible. This allows factory placement of the intake to be used without placing the filter lower in the vehicle where it can be subjected to engine harming road debris or fluid.

DO YOU NEED AN SAI KIT?

The MK5/MK6 2.0T TSI engine has two different engine codes. CBFA engine codes are equipped from the factory with a secondary air injection (SAI) pump that connects to the factory intake box. These engines require a small breather filter for this SAI line when installing an aftermarket intake. CCTA engine codes do not have this SAI pump and will not require this filter. Identify your engine code using the photos below, and add an SAI filter kit above if needed when ordering your intake.

EASY INSTALLATION

Installation is quick and easy to install with basic tools. The process should take around an hour for most enthusiasts.

CLICK HERE to view and download the Cold Air Intake install guide

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers.

TURBO INLET PIPE FEATURES

• Greatly improves air-flow to turbocharger
• Constant high-flow inner diameter
• Easy install, no modifications necessary
• Long life cast aluminum alloy
• In-house CNC machined for perfect fitment
• No leak o ring seal to turbocharger 
• Outflows stock inlet by 110CFM

IS YOUR STOCK INLET ROBBING POWER?

The factory installed plastic turbo inlet found installed on your VW or Audi Gen 3 1.8T or 2.0T TSI engine is adequate enough for stock cars with factory hardware and ECU calibrations. However, the necked down design becomes a major flow restriction when ran with power upgrades such as cold air intakes, intercoolers, downpipes, and ECU upgrades. 

UPGRADE YOUR TURBO INLET PIPE

The IE Turbo Inlet Pipe helps you to get the most out of your IS38 or IS20 turbo and power upgrades by removing the factory flow restriction. The cast aluminum design allows for a constant diameter elbow increasing efficiency from the intake to the turbo without the bottleneck design of the factory unit.

HORSEPOWER RESULTS

Dyno graph tested on a 2019 GTI with Stage 2 hardware & software on 93 octane

EASY INSTALLATION

Your new turbo inlet pipe has been in-house CNC machined and includes all required hardware to allow for a perfect and easy installation. View and download the install guide here (coming soon).

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers. 

VEHICLE APPLICATIONS

• Audi - A3 2015+ 8V 1.8T & 2.0T engines
• Audi - S3 2015+ 8V 2.0T engine
• Audi - TT 2016+ 8S 2.0T engine
• Audi - TTS 2016+ 8S 2.0T engine
• VW - Golf R 2015+ MK7 2.0T engine
• VW - GTI 2015+ MK7 2.0T engine
• VW - Golf/Alltrak 2015+ MK7 1.8T & 2.0T
• VW - Passat 2013+ B8 1.8T & 2.0T (EA888 Gen 3) engines
• VW - Tiguan 5N 2017+ 2.0T (EA888 Gen 3) engine

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

Modernise your vehicle by upgrading the radio to an RCD330G+ with it's built in bluetooth, Apple CarPlay, Mirrorlink & Android Auto.

Compatibility:

• MK5 2005+
• MK6 including
• Jetta (2007 - 2013)
• EOS (2007 - 2013)
• Polo 6R (2007 - 2013)
• Scirocco R
• Tiguan (2006- 2014)
• Caddy (2006 - 2014)
• Passat (2006 - 2014)
• T5 Transporter 

Take advantage of the latest CarPlay functionality by upgrading your iPhone to iOS 14. 

Package Contents:

•  1 x RCD330G+ Radio (187B No Name)
•  1 x Antenna Adapter
•  1 x AV Camera Adapter

Tech Specs:

• 6.5" Touchscreen Display
• Resolution 800 x 480
• Video Input for the OEM Rear View Camera (Please note Genuine factory fitted reverse cameras will require RGBS to AV Converter)
• AM / FM Radio with RDS
  

• Slot for SD Card (Max 32GB)
• USB Port for Apple CarPlay & Android Auto
• AUX Input
• Supports Factory OPS (Optical Parking System)
• Supports Multi-Function Steering Wheel (Steering Wheel Adapter Harness will be required for MK5 Platform)
• Built-In Bluetooth

Additional Information:
Please note for vehicles prior to 2008, you will need to upgrade your CAN Gateway to prevent battery drain.
Will NOT work on an VW Polo 6C MQB

Retain your VW MK5's 8-button steering wheel controls after installing an RCD330G with this plug and play harness.

This harness is designed to retain the use of every button on your factory steering wheel which will communicate with your RCD330G headunit.

Simply plug in this harness directly into the back of your RCD330G headunit, followed by your vehicles factory quadlock. 

Compatible with:

- Golf Mk5

- Jetta Mk5

- Passat B6

Radio models:

- RCD330

- RCD340

- RCD360

- RNS510

- RCD510