Volkswagen - IPE - Integrated Engineering - Supernova - Genuine VW - VW Central - Flow Designs - Autotech

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers.

TURBO INLET PIPE FEATURES

• Greatly improves air-flow to turbocharger
• Constant high-flow inner diameter
• Easy install, no modifications necessary
• Long life cast aluminum alloy
• In-house CNC machined for perfect fitment
• No leak o ring seal to turbocharger 
• Outflows stock inlet by 110CFM

IS YOUR STOCK INLET ROBBING POWER?

The factory installed plastic turbo inlet found installed on your VW or Audi Gen 3 1.8T or 2.0T TSI engine is adequate enough for stock cars with factory hardware and ECU calibrations. However, the necked down design becomes a major flow restriction when ran with power upgrades such as cold air intakes, intercoolers, downpipes, and ECU upgrades. 

UPGRADE YOUR TURBO INLET PIPE

The IE Turbo Inlet Pipe helps you to get the most out of your IS38 or IS20 turbo and power upgrades by removing the factory flow restriction. The cast aluminum design allows for a constant diameter elbow increasing efficiency from the intake to the turbo without the bottleneck design of the factory unit.

HORSEPOWER RESULTS

Dyno graph tested on a 2019 GTI with Stage 2 hardware & software on 93 octane

EASY INSTALLATION

Your new turbo inlet pipe has been in-house CNC machined and includes all required hardware to allow for a perfect and easy installation. View and download the install guide here (coming soon).

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers. 

VEHICLE APPLICATIONS

• Audi - A3 2015+ 8V 1.8T & 2.0T engines
• Audi - S3 2015+ 8V 2.0T engine
• Audi - TT 2016+ 8S 2.0T engine
• Audi - TTS 2016+ 8S 2.0T engine
• VW - Golf R 2015+ MK7 2.0T engine
• VW - GTI 2015+ MK7 2.0T engine
• VW - Golf/Alltrak 2015+ MK7 1.8T & 2.0T
• VW - Passat 2013+ B8 1.8T & 2.0T (EA888 Gen 3) engines
• VW - Tiguan 5N 2017+ 2.0T (EA888 Gen 3) engine

Whether your looking to save hundreds on highly priced dealer xenon globes or wanting more out of your xenon projector headlights, ATOM brings higher output, colour rendering index and colour temperature over traditional big brand xenon globes without the excessive price tag.

Description No Coding, Direct Install Get a unique sweeping / dynamic / sequential LED appearance by simply upgrading the LED module on your Golf Mk5 with our dynamic variant. Made specifically for Mk5 Golf, incorporating the same socket as OEM for easy install, no further coding or modification needed. Plug N Play – no coding needed Easy 10 min install No coding needed All Tools Included FITS All VW Golf MK5 models 2003-2008 R32/GTI/GT/TSI/TDI Does not fit VW Golf Mk6 Details Shop Mk6 Mirror Lights Here Shop Mk7 Mirror Lights Here

Experiencing Misfires on your car? Don't go OEM again!
Upgrade your coilpacks to these sporty, redtop R8 coilpacks! Used on the Audi R8 V8 and V10, these coilpacks offer a stronger spark than factory, reducing troublesome misfire on performance upgraded and tuned VAG vehicles

Buy a set of 4 Now!

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

W MK5 Golf R32 Front Splitter + Pre Mounted Aero Spacers Kit Includes Splitter(s) 2 Flow Designs Stickers Fitting kit Material 10mm Thick Polyethylene Composite, Bevelled edges Finish HAND POLISHED SATIN BLACK Why do we use Polyethylene Composite for Flow Designs Splitters? Strong, impact resistant, doesn't corrode or chip, and has excellent abrasion resistance (say… from scraping on driveways and road all the time?) Carbon Fibre is better isn’t it? As strong and light as Carbon fibre is, it CRACKS on impact or when under load and/or stress. Clear coat will eventually fades & cracks and become undesirable.

VW MK5 Golf R32 Side Splitter Kit Includes Splitter(s) 2 Flow Designs Stickers Fitting kit Material 10mm Thick Polyethylene Composite, Bevelled edges Finish HAND POLISHED SATIN BLACK Why do we use Polyethylene Composite for Flow Designs Splitters? Strong, impact resistant, doesn't corrode or chip, and has excellent abrasion resistance (say… from scraping on driveways and road all the time?) Carbon Fibre is better isn’t it? As strong and light as Carbon fibre is, it CRACKS on impact or when under load and/or stress. Clear coat will eventually fades & cracks and become undesirable.

VW MK5 Golf GTI Front Splitter + Aero Spacers Kit Includes Splitter(s) Pre-mounted Adjustable Aero Spacers 2 Flow Designs Stickers Fitting kit Material 10mm Thick Polyethylene Composite, Bevelled edges Finish HAND POLISHED SATIN BLACK Why do we use Polyethylene Composite for Flow Designs Splitters? Strong, impact resistant, doesn't corrode or chip, and has excellent abrasion resistance (say… from scraping on driveways and road all the time?) Carbon Fibre is better isn’t it? As strong and light as Carbon fibre is, it CRACKS on impact or when under load and/or stress. Clear coat will eventually fades & cracks and become undesirable.

Volkswagen Scirocco PFL/FL Side Splitters (Pair) Details: Finish the aero styling of your Scirocco street project with Flow Designs splitter set, complete with front & side splitters, rear spats & rear valance. The set fits facelift & prefacelift bumpers, with a guarantee of impact resistance on all splitters. Fast Australian & international delivery! Kit Includes: Side splitters (pair) to suit pre-facelift and facelift Scirocco R 2 Flow Designs stickers Fitting kit Material: 10mm thick polyethylene composite, bevelled edges Finish: Hand polished satin black Why do we use Polyethylene Composite for Flow Designs Splitters? Strong, impact resistant, doesn't corrode or chip, and has excellent abrasion resistance (say… from scraping on driveways and road all the time?) Carbon Fibre is better isn’t it? As strong and light as Carbon fibre is, it CRACKS on impact or when under load and/or stress. Clear coat will eventually fades & cracks and become undesirable.