GTI/GTD - CTS Turbo - Forge Motorsports - New South Performance - XFORCE - Vogtland - Eibach - VW Central

For drivers side vent of RHD 2015 GTI or Golf.Not for Jetta

This product will only bolt directly to an Xforce axle back system.

• 3" dump pipe from turbo
• 100 cell high flow cat
• "3 connector pipe with resonator
• Will only bolt directly to an Xforce axle back system

 

Xforce is proud to announce our resonator delete kit for the MK7/MK7.5 Golf GTI platforms.Get all the benefits of using this resonator delete (based on factory Audi part) without the high price tag.

MK7 Golf/GTI/Golf R 8V Audi A3/S3 MK3 Audi TT/TT-S

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

CTS Turbo is proud to release our 187mm Dual Pulley Upgrade Kit for Supercharged 3.0T V6 engines (press-on style).

The smaller diameter supercharger pulley and larger diameter crank pulley will increase the speed at which the supercharger spins and will increase the boost pressure output.  Increased boost pressure in conjunction with upgraded ECU software results in a dramatic increase in horsepower and torque throughout the entire powerband. This will not drastically increase stress or excessive wear on supercharger or engine components.

This kit features press-on style supercharger pulley. Check on your vehicle before ordering!

NOTE: This kit must be used with appropriate “Stage 2+” or equivalent performance software. Please contact your tuner. Use of upgraded heat exchanger is highly recommended.

This is a CTS Turbo universal 3.5″ cone filter, it has a tapered design primarily used in our MK7 GTI/GOLF R, B9 AUDI A4, B8/B8.5 S4, S5  intake kits.  These filters can also be used in a custom big turbo application.

Product Details:

3.5″ Inlet x 8.0″ Long x 6.0″ Wide
High quality moulded silicon base and cap
Stainless steel clamp

Fitment:

• CTS-IT-270R or CTS-IT-270
• CTS-IT-290
• CTS-IT-300

Now fully compatible with all 2018-2020 Audi RS3/TTRS 2.5T DAZA and DNWA engines, this is one kit to fit them all!

CTS Turbo is proud to announce our improved 8V, 8V.2/8S Audi RS3/TTRS Throttle Body Inlet Kit for DAZA and DNWA

Our high flow throttle body inlet is designed it to be larger, but also more aerodynamic than the stock part. Our inlet has a 56% internal volume increase over the stock inlet. Using the latest CAD software, the shape of the inlet tract was flow optimized and cast from aluminum for best performance. All critical parts were CNC machined to ensure perfect fitment and performance.

We have also included our machined throttle body spacer from with two additional ports for boost reference and methanol injection; as well and a high-flow 2.75″ throttle inlet pipe. Custom-made silicone couplers and t-bolt clamps allow for seamless, easy installation.

Features:

• CAD optimized for maximum flow, 56% larger than factory
• Cast aluminum throttle body elbow, billet aluminum spacer
• CNC machined in house for perfect fitment
• Direct replacement for factory parts between the cold side of the intercooler and the throttle body
• HP gain of up to 20hp on stock turbo, even more with big turbo upgrades
• Compatible with factory intake, CTS Turbo intakes and most other popular intakes (not compatible with Eventuri intake)
• Compatible with factory and aftermarket intercoolers
• Includes a large-bore 2.75″ charge pipe and custom silicone couplers
• Two extra 1/8″ NPT bungs on the charge pipe for watermeth nozzles
• Compatible with 1-bolt and 2-bolt pressure sensors
• DV flange is based on factory design
• Includes hoses and fittings to install on 2019+ DNWA engines

Fitment:

• 8V and 8V.2 Audi RS3 (2018-2020) – DAZA and DNWA models
• 8S Audi TT-RS (2018-2020) – DAZA and DNWA models