GTI/GTD - Turbosmart - New South Performance - XFORCE - VW Central - Flow Designs

Turbosmart's new Kompact Shortie Blow-Off Valve for VAG 2.0 TSI engines takes performance to the next level. These valves are a high performance replacement for the standard diverter valve fitted to the current 2.0 TSI range. Unlike the standard valve's plastic construction, they are machined from aircraft grade aluminium, and bolt straight up to the factory location, offering all the technology from Turbosmart's race-bred BOV range in an OEM-replacement package. The Dual Port offers a 50/50 split between recirculating and vent-to-atmosphere, for quiet operation at low boost, and the high performance sound associated with vent-to-atmosphere BOVs at higher boost. The Dual Port also recirculates enough air to keep the car's ECU happy. Turbosmart's Kompact Shortie does not leak, bleed boost pressure or struggle with increased boost on tuned vehicles. It also completely eliminates compressor surge, allowing the turbo to operate to its full potential, and for longer.

Turbosmart's new Kompact Shortie Blow-Off Valve for the Mk7 takes performance to the next level. These valves are a high performance replacement for the Golf's standard diverter valve. Unlike the standard valve's plastic construction, they are machined from aircraft grade aluminium, and bolt straight up to the factory location, offering all the technology from Turbosmart's race-bred BOV range in an OEM-replacement package. The Plumb Back is a 100% recirculating blow-off valve, routing all vented air back into the intake. This valve operates at a similar level of volume to the standard valve, avoiding unwanted attention. Turbosmart's Kompact Shortie does not leak, bleed boost pressure or struggle with increased boost on tuned vehicles. It also completely eliminates compressor surge, allowing the Golf's turbo to operate to its full potential, and for longer.

• Plug and play compatability
• 400% stronger than the OE Diverter Valve
• Designed to handle boost pressure up to 30PSI
• Ideal for lightly modified vehicles

For drivers side vent of RHD 2015 GTI or Golf.Not for Jetta

This product will only bolt directly to an Xforce axle back system.

• 3" dump pipe from turbo
• 100 cell high flow cat
• "3 connector pipe with resonator
• Will only bolt directly to an Xforce axle back system

 

Xforce is proud to announce our resonator delete kit for the MK7/MK7.5 Golf GTI platforms.Get all the benefits of using this resonator delete (based on factory Audi part) without the high price tag.

Are you sick and tired of plugging your Apple iPhone into the USB port every time you get into your car. At VW Central we have found the solution for factory fitted vehicles. Simply plug our USB adapter into the factory USB port and it will use Bluetooth to make a wireless connection with your vehicle. Plug and Play. No coding required. Please note this will not work if your vehicle doesn’t already have factory fitted CarPlay functionality. Suitable for VW Vehicles 2016+

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

Volkswagen MK7 Golf GTI Front Splitter & Aerospacers

Details:

The Flow Designs splitter set is the best exterior mod for your VW MK7 Golf GTI! With front & side splitters & rear valance, Flow Designs offer the strongest splitters on the market. Easy install & perfect fitment guaranteed, with Australia-wide & international shipping on all products.

By purchasing this splitter, the pre-pressed in threaded brass inserts will now accept all our add-on accessories for the MK7 GTI such as winglets and splitter extensions.

---

Kit Includes:

• Front splitter with pre-pressed in threaded brass inserts (Front Extensions and Front Winglets sold separately)
• Bumper reinforcement bracket
• Pre-mounted adjustable Aerospacers
• 2 Flow Designs stickers
• Fitting kit

CNC engraved logo and features, hand polish and packed all in Melbourne's outer east.

Material:

• Front Splitter: 10mm thick polyethylene composite

Finish:

• Hand polished satin black
• Bevelled edges

Why do we use Polyethylene Composite for Flow Designs Splitters?

Strong, impact resistant, doesn't corrode or chip, and has excellent abrasion resistance (say… from scraping on driveways and road all the time?)

Carbon Fibre is better isn’t it?

As strong and light as Carbon fibre is, it CRACKS on impact or when under load and/or stress. Clear coat will eventually fades & cracks and become undesirable.

 

Shipping Dimensions for the type of product:

Front
184x55x5 @5kg

Side
194x14x4 @5kg

Diffuser
92x25x7 @2kg

Spat
25x25x4 1kg

Winglets
25x13x11 @.5kg