MK5 GTI (2006-2009)

Kompact VAG V2 Plumb Back has been specifically to suit the 2.0L VAG engine Unlike the standard, plastic valves that use un-reinforced diaphragms and are known to crack under increased boost, the new Kompact VAG V2 Plumb Back uses O-Ring sealed piston which, coupled with it's billet aluminium construction give it over 30PSI boost handling capability. Included with each Kompact VAG V2 Plumb Back kit: Model specific valve, Mounting screws and Spring clamps.

Kompact VAG 2.0T V2 - Dual Port TS-0203-1041 Details Applications Instructions Accessories Kompact VAG V2 Dual Port has been specifically to suit the 2.0L VAG engine Unlike the standard, plastic valves that use un-reinforced diaphragms and are known to crack under increased boost, the new Kompact VAG V2 Dual Port uses O-Ring sealed piston which, coupled with it's billet aluminium construction give it over 30PSI boost handling capability. VAG V2 Dual Port kit: Model specific valve, Mounting screws and Spring clamps.

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

 

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.  

CTS Turbo is proud to release our B-Cool Billet Oil Filter Housing.  The OE plastic filter housing is quite fragile and is know to become brittle and crack over time.  Each CTS Turbo B-Cool Billet Oil Filter Housing is constructed in house from T6061 Aluminum.  Not only does the B-Cool filter look good, but it works great.  We have engineered cooling fins into our design to act as a heatsink, which dissipates heat from the engine oil.

Installation is very straight forward and only required basic hand tools:

Drain oil from filter housing, use a 36mm socket to remove the factory oil filter housing, install new filter, install new filter housing o-ring to CTS housing, reinstall on the car and tighted to 18 ft/lbs, refill engine oil.

Product Details:

•   Made in Canada from billet T6061 Aluminum
•   Hard anodized black for stealth and longevity (machined finish shown)
•   Uses OEM O-ring
•   Installation of CTS-HW-0242 requires removal of center cage from OE housing cap, which snaps into the CTS billet housing
•   OE-style threads are precision made to fit just like factory part. Other manufacturers do NOT make this thread.
•   Compatible with OEM Filter

The CTS B-Cool Billet fits Audi, VW, Seat, Skoda models with EA113 2.0T FSI engines, 2.5L 5-cylinder engines and 2.5T 5-cylinder turbo engines.

This part replaces the OE part# 06D 115 408B and 07K 115 408.

Fitment:

• MK6 Golf R, MK5 GTI (FSI), 8P Audi A3 (FSI), MK2 Audi TT-S (FSI)
• MK5 and MK6 Golf, Jetta 2.5 5-cylinder
• 8P Audi RS3 (not for facelift model)
• MK2 Audi TT-RS (not for facelift models)