MK7.5 GTI (2017+) - CTS Turbo - IPE - Leyo Motorsport - P3 Cars - Eibach - Maxton Design

Product Description:

Eibach’s Pro-Kit Lowering Springs (E10-85-051-05-22) are an essential upgrade component to your vehicles suspension & chassis setup. Please carefully check compatibility, any pre-requisites for suspension setups (including front & rear axle load and electronic dampening setups). Motorsport has always been one of Eibach’s core competencies and the testing ground for numerous innovations. Eibach’s passion for precision is what racing enthusiasts worldwide appreciate.

Technical Information

Eibach Part: E10-85-051-05-22
Range: Pro-Kit
Front Lowering: 15-20mm (Max front axle load: 1070kg)
Rear Lowering: 10mm (Max rear axle load: 930kg)
Axle: Multi-Link Axle, for all standard damping systems

• World's leading Performance Suspension Spring System
• Engineered and tested to work perfectly with stock dampers
• First step towards a complete sport suspension system
• Lower center of gravity ? lowers vehicle up to 40 mm
• Lowering = Traction + Attraction
• Progressive spring design
• Performance handling

• World's leading Performance Suspension Spring System
• Engineered and tested to work perfectly with stock dampers
• First step towards a complete sport suspension system
• Lower center of gravity ? lowers vehicle up to 40 mm
• Lowering = Traction + Attraction
• Progressive spring design
• Performance handling

CTS Turbo Blankets isolate the heat produced by your IHI IS12/IS20/IS38 turbocharger with the purpose of reducing turbo lag, cooler air intake temperatures, protecting and prolonging engine components, and giving a boost in horsepower.  In keeping the heat of the exhaust gases contained within the hot side of the turbocharger and away from the cool side of the turbocharger and the intake path, more oxygen per unit volume reaches the engine, and thus, more power.

This turbo blanket fits all IHI turbos found on MQB platform cars

IS12 Turbos found on MK7 1.8TSI Golf and 8V Audi A3 FWD

IS20 Turbos found on MK7 GTI and 8V Audi A3 Quattro

IS38 Turbos found on the MK7 Golf R and 8V Audi S3

CTS Turbo Blanket Heat Tolerance:

Interior Surface:
Max Temperature Rating: 2100 Deg F
Continuous Use Limit: 1800 Deg F

Exterior Surface:
Direct Contact Limit: 800 Deg F
Radiant Heat Limit: 1200 Deg F

CTS Turbo is proud to offer our upgraded turbo inlet hose for the MK7+ VW and 8V Audi MQB vehicles.  The factory turbo inlet hose is corrugated with internal ridges that disrupt air flow.  Not only do they reduce air flow, but the plastic can become weak over time causing leaks and reduced performance.

The CTS Turbo turbo inlet hose is constructed from 5-ply silicone that will not collapse, even under heavy load. This is MUCH stronger than other inlet hoses offered by different companies. Collapsing intake hose can cause turbo to fail!!

The CTS Turbo inlet hose allows for smooth uninterrupted flow and more air pumping through your engine!

Features:

• Designed to fit factory airbox and any turbo inlet pipe
• 5-ply silicone construction
• Smooth interior
• High strength hose clamps

Components:
1 x CTS Turbo MQB Turbo Inlet Hose
2 x Hose clamps

Fits the following vehicles:

• MK7 VW GTI
• MK7 VW Golf R
• MK7 Audi A3
• MK7 Audi S3

This is a CTS Turbo universal 3.5″ cone filter, it has a tapered design primarily used in our MK7 GTI/GOLF R, B9 AUDI A4, B8/B8.5 S4, S5  intake kits.  These filters can also be used in a custom big turbo application.

Product Details:

3.5″ Inlet x 8.0″ Long x 6.0″ Wide
High quality moulded silicon base and cap
Stainless steel clamp

Fitment:

• CTS-IT-270R or CTS-IT-270
• CTS-IT-290
• CTS-IT-300

P3 V3 Gauge Features

• Plug and Play Install - plugs directly into your OBD2 port (want to keep your OBD2 port open? hard-wire harness kit also available)
• OEM Integration - installs in your vent for a sleek install while retaining air flow
• Versatility - read boost from multiple OEM sensors through OBD2 port or using optional P3 analog boost sensor
• Code Reading/Clearing - read and clear diagnostic trouble codes (DTCs) on the fly

P3 V3 Gauge Readouts (all readouts can be individually configured to read in either Imperial or Metric units)

• Boost (through OBD2 port using OEM sensors or with P3 analog boost sensor)
• Coolant temperature
• Air/Fuel ratio (can be read in AFR or Lambda)
• Vehicle speed (can be calibrated in 1% increments from -9% to +20%)
• Intake air temperature
• Throttle angle
• Ignition timing
• Engine RPM
• Exhaust gas temperature
• Battery voltage
• Programmable shift light
• Analog input 1 (brown wire) can allow gauge to read any 0-5 volt linear output sensor
• Analog input 2 (blue wire) can allow gauge to read any 0-5 volt linear output sensor
• Acceleration timers (0-60mph/0-100mph/60-130mph)
• Braking timers (60-0mph/100-0mph)

OEM Vent Option

• We install the display in an OEM vent to make your install even easier

Optional Add-Ons

• P3 Analog Boost sensor - plugs directly into gauge harness, no wiring required)
• Boost tubing kit - Approx. 5' of 5/32" O.D. flexible plastic boost tubing with vacuum "T" and 3 sections of 5/32" I.D. vaccum hose. Includes 3 zip ties
• P3 ESVA (Ethanol Sensor Voltage Adaptor) allows your gauge to read ethanol content and fuel temperature directly from the common Continental/GM flex fuel sensor. *Ethanol sensor NOT included
• Trim Removal Kit - this tool kit will help you remove your vent and interior trim while minimizing the chance of scratching or damaging your trim
• OBD2 Splitter - attach multiple devices to your OBD2 port. *some devices will not function while another device is attached to the OBD2 port

You asked, we answered.

The P3 V3 Gauge adds even more user control to what the OBD2 Multi-Gauge already offered. Read DTCs on command, remove pids that you don't care to see, configure units settings of individual measurements, calibrate your vehicle speed, read AFR in Lambda.

There when you need it, hidden when you don't.

No more bulky pillar or column pods... No more squinting to read tiny pixelated screens...  While retaining the OEM plus design that blends into your interior, the P3 V3 packs a punch with it's bold, bright display that allows you to pick up info at a glance.

Hot or Cold? No problem!

Even though the P3 V3 installs in your air vent, we keep in mind that you need that heat and A/C while designing each gauge.

Electronics in a harsh climate? We've got that covered too.

We've torture-tested our gauges to the extreme. From frozen solid at -94 F to physically melting at hundreds of degrees, our gauges function far beyond the limits of the in-car environment.