MK7.5 GTI (2017+) - CTS Turbo - H&R Springs - XFORCE

This product will only bolt directly to an Xforce axle back system.

• 3" dump pipe from turbo
• 100 cell high flow cat
• "3 connector pipe with resonator
• Will only bolt directly to an Xforce axle back system

VW GTI MK6 & MK7/MK7.5 GTI

• Burnt Blue Coating Look

4" Black Tips for use with Xforce MK6 & MK7/MK7.5 GTI Systems. 

CTS Turbo Blankets isolate the heat produced by your IHI IS12/IS20/IS38 turbocharger with the purpose of reducing turbo lag, cooler air intake temperatures, protecting and prolonging engine components, and giving a boost in horsepower.  In keeping the heat of the exhaust gases contained within the hot side of the turbocharger and away from the cool side of the turbocharger and the intake path, more oxygen per unit volume reaches the engine, and thus, more power.

This turbo blanket fits all IHI turbos found on MQB platform cars

IS12 Turbos found on MK7 1.8TSI Golf and 8V Audi A3 FWD

IS20 Turbos found on MK7 GTI and 8V Audi A3 Quattro

IS38 Turbos found on the MK7 Golf R and 8V Audi S3

CTS Turbo Blanket Heat Tolerance:

Interior Surface:
Max Temperature Rating: 2100 Deg F
Continuous Use Limit: 1800 Deg F

Exterior Surface:
Direct Contact Limit: 800 Deg F
Radiant Heat Limit: 1200 Deg F

CTS Turbo is proud to offer our upgraded turbo inlet hose for the MK7+ VW and 8V Audi MQB vehicles.  The factory turbo inlet hose is corrugated with internal ridges that disrupt air flow.  Not only do they reduce air flow, but the plastic can become weak over time causing leaks and reduced performance.

The CTS Turbo turbo inlet hose is constructed from 5-ply silicone that will not collapse, even under heavy load. This is MUCH stronger than other inlet hoses offered by different companies. Collapsing intake hose can cause turbo to fail!!

The CTS Turbo inlet hose allows for smooth uninterrupted flow and more air pumping through your engine!

Features:

• Designed to fit factory airbox and any turbo inlet pipe
• 5-ply silicone construction
• Smooth interior
• High strength hose clamps

Components:
1 x CTS Turbo MQB Turbo Inlet Hose
2 x Hose clamps

Fits the following vehicles:

• MK7 VW GTI
• MK7 VW Golf R
• MK7 Audi A3
• MK7 Audi S3

CTS Turbo is proud to release our 187mm Dual Pulley Upgrade Kit for Supercharged 3.0T V6 engines (press-on style).

The smaller diameter supercharger pulley and larger diameter crank pulley will increase the speed at which the supercharger spins and will increase the boost pressure output.  Increased boost pressure in conjunction with upgraded ECU software results in a dramatic increase in horsepower and torque throughout the entire powerband. This will not drastically increase stress or excessive wear on supercharger or engine components.

This kit features press-on style supercharger pulley. Check on your vehicle before ordering!

NOTE: This kit must be used with appropriate “Stage 2+” or equivalent performance software. Please contact your tuner. Use of upgraded heat exchanger is highly recommended.

Introducing the NEW XFORCE Downpipe offering to suit Audi PFL RS3 8V 09/2015-12/2016. 

Experience more performance from your Audi RS3 by bolting on our XFORCE Performance Exhaust Turbo Downpipe.

The turbo downpipe stainless steel pipe kit which is equipped with a high-flow cat to achieve maximum flow. Your Audi RS3 will come alive and demand attention!

Over 20 years of exhaust development and technical expertise have gone into creating the ultimate bolt-on performance downpipes, providing power increases throughout the rev range.

Dump-Pipe & Cat Kit

• Features

  • Stainless Steel
  • Non Polished 3.5″ – 3″ pipe work
  • Stainless Steel Flex Bellow
  • 200 Cell Metallic High Flow Cat
  • Additional Tuning pipe
  • 3″ to Twin OEM size adaptor pipe
  • Fitting kit supplied

  Part No:	ESRS315KITB
  Vehicle Model:	RS3
  Material:	304 Stainless Steel

  
  COMPATIBLE