MK7.5 GTI (2017+) - CTS Turbo - Integrated Engineering - P3 Cars

CTS Turbo Blankets isolate the heat produced by your IHI IS12/IS20/IS38 turbocharger with the purpose of reducing turbo lag, cooler air intake temperatures, protecting and prolonging engine components, and giving a boost in horsepower.  In keeping the heat of the exhaust gases contained within the hot side of the turbocharger and away from the cool side of the turbocharger and the intake path, more oxygen per unit volume reaches the engine, and thus, more power.

This turbo blanket fits all IHI turbos found on MQB platform cars

IS12 Turbos found on MK7 1.8TSI Golf and 8V Audi A3 FWD

IS20 Turbos found on MK7 GTI and 8V Audi A3 Quattro

IS38 Turbos found on the MK7 Golf R and 8V Audi S3

CTS Turbo Blanket Heat Tolerance:

Interior Surface:
Max Temperature Rating: 2100 Deg F
Continuous Use Limit: 1800 Deg F

Exterior Surface:
Direct Contact Limit: 800 Deg F
Radiant Heat Limit: 1200 Deg F

CTS Turbo is proud to offer our upgraded turbo inlet hose for the MK7+ VW and 8V Audi MQB vehicles.  The factory turbo inlet hose is corrugated with internal ridges that disrupt air flow.  Not only do they reduce air flow, but the plastic can become weak over time causing leaks and reduced performance.

The CTS Turbo turbo inlet hose is constructed from 5-ply silicone that will not collapse, even under heavy load. This is MUCH stronger than other inlet hoses offered by different companies. Collapsing intake hose can cause turbo to fail!!

The CTS Turbo inlet hose allows for smooth uninterrupted flow and more air pumping through your engine!

Features:

• Designed to fit factory airbox and any turbo inlet pipe
• 5-ply silicone construction
• Smooth interior
• High strength hose clamps

Components:
1 x CTS Turbo MQB Turbo Inlet Hose
2 x Hose clamps

Fits the following vehicles:

• MK7 VW GTI
• MK7 VW Golf R
• MK7 Audi A3
• MK7 Audi S3

CTS Turbo is proud to release our 187mm Dual Pulley Upgrade Kit for Supercharged 3.0T V6 engines (press-on style).

The smaller diameter supercharger pulley and larger diameter crank pulley will increase the speed at which the supercharger spins and will increase the boost pressure output.  Increased boost pressure in conjunction with upgraded ECU software results in a dramatic increase in horsepower and torque throughout the entire powerband. This will not drastically increase stress or excessive wear on supercharger or engine components.

This kit features press-on style supercharger pulley. Check on your vehicle before ordering!

NOTE: This kit must be used with appropriate “Stage 2+” or equivalent performance software. Please contact your tuner. Use of upgraded heat exchanger is highly recommended.

This is a CTS Turbo universal 3.5″ cone filter, it has a tapered design primarily used in our MK7 GTI/GOLF R, B9 AUDI A4, B8/B8.5 S4, S5  intake kits.  These filters can also be used in a custom big turbo application.

Product Details:

3.5″ Inlet x 8.0″ Long x 6.0″ Wide
High quality moulded silicon base and cap
Stainless steel clamp

Fitment:

• CTS-IT-270R or CTS-IT-270
• CTS-IT-290
• CTS-IT-300

Now fully compatible with all 2018-2020 Audi RS3/TTRS 2.5T DAZA and DNWA engines, this is one kit to fit them all!

CTS Turbo is proud to announce our improved 8V, 8V.2/8S Audi RS3/TTRS Throttle Body Inlet Kit for DAZA and DNWA

Our high flow throttle body inlet is designed it to be larger, but also more aerodynamic than the stock part. Our inlet has a 56% internal volume increase over the stock inlet. Using the latest CAD software, the shape of the inlet tract was flow optimized and cast from aluminum for best performance. All critical parts were CNC machined to ensure perfect fitment and performance.

We have also included our machined throttle body spacer from with two additional ports for boost reference and methanol injection; as well and a high-flow 2.75″ throttle inlet pipe. Custom-made silicone couplers and t-bolt clamps allow for seamless, easy installation.

Features:

• CAD optimized for maximum flow, 56% larger than factory
• Cast aluminum throttle body elbow, billet aluminum spacer
• CNC machined in house for perfect fitment
• Direct replacement for factory parts between the cold side of the intercooler and the throttle body
• HP gain of up to 20hp on stock turbo, even more with big turbo upgrades
• Compatible with factory intake, CTS Turbo intakes and most other popular intakes (not compatible with Eventuri intake)
• Compatible with factory and aftermarket intercoolers
• Includes a large-bore 2.75″ charge pipe and custom silicone couplers
• Two extra 1/8″ NPT bungs on the charge pipe for watermeth nozzles
• Compatible with 1-bolt and 2-bolt pressure sensors
• DV flange is based on factory design
• Includes hoses and fittings to install on 2019+ DNWA engines

Fitment:

• 8V and 8V.2 Audi RS3 (2018-2020) – DAZA and DNWA models
• 8S Audi TT-RS (2018-2020) – DAZA and DNWA models

LEADING FEATURES

• Required for IE TrueFlex MQB tunes
• Allows for instant adjustments from 91 pump to full E85
• Harness for VW MK7 & Audi 8V EA888.3 engines
• Sends sensor data in real-time to IE ECU calibrations
• Includes everything needed to install

OVERVIEW

This plug and play harness kit is required for IE TrueFlex ECU Tunes for VW and Audi MQB Gen 3 engines. This includes everything necessary for the flex-fuel sensor to send real-time data from your fuel system to the ECU and adjust for any content mix from 91 pump to full E85 automatically.

Kit includes:

• (1x) IE TrueFlex Wiring Harness
• (1x) 2 amp Fuse
• (1x) Ethanol Sensor
• (2x) Ethanol Sensor Quick Connect Couplers
• (2x) Hose Clamps

INSTALLATION

This harness kit is fully assembled to proper lengths and includes everything needed to install in a clean and factory-like install. Disconnecting and cutting of factory soft fuel lines is required and should be completed with great care or by a professional.

TrueFlex is currently available for 2015-2018 MK7 GTI & A3 2.0T W/IS38. Stage 1 & 2, Golf R/S3, and 2019+ model years are coming soon!

EXPLORE WITH CONFIDENCE

Upgrading your IE 5" velocity stack intake with our harsh climate filter kit will further keep your engine safe when traveling on dirt roads, sandy beaches, or anywhere with dusty contaminants in the air. 

KIT DETAILS

This complete filter kit uses a 3 step approach to combat harsh climates. The filter has been increased from a 6 pleat construction to 8 pleats to increase cotton density. The cotton pleats are then treated with a penetrating filter oil to further catch and trap particulates. As a final measure, a pre-filter sock adds a final layer of protection over the filter. Together, these 3 barriers offer superior filtration for your intake system over our standard performance air filter.

KIT CONTENTS:

• 1X IE oiled 8 pleat density performance 5" filter
• 1X IE pre-filter intake sock
• 1X Air filter worm clamp 

RECHARGING

As the air filter does its job of effectively catching more particulates, eventually it will have to be cleaned and maintained. We recommend washing your cotton filter in water with a little Dawn dish soap, rinsing thoroughly, and allowing it to completely air dry. To replace the oil, any off-the-shelf filter oil kit from your local auto parts supply chain can be used. Do not over-oil the filter, a little goes a long way. 

COMPATIBLE INTAKES

Our 5" Harsh Climate Oiled Air Filter & Sock Upgrade Kit is a direct replacement filter for all popular IE air intake kits with a 5" velocity stack. 

• IEINCI11 - IE MQB 2.0T/1.8T Gen 3 Cold Air Intake
• IEINCK3 - IE Carbon Fiber Intake System For Audi B9 S4 & S5 3.0T
• IEINCG2A - IE Audi 3.0T Cold Air Intake For B8/B8.5 S4 & B8.5 S5
• IEINCN1 - IE Audi 3.0T Cold Air Intake For C7 A6 & A7
• IEINSG1 - IE Audi 3.0T Cold Air Intake For 8R SQ5 & Q5
• IEINCG1 - IE Audi 2.0T TSI Cold Air Intake For B8/B8.5 A4 & A5
• IEINCK1 - IE Audi B9 A4 & A5 Cold Air Intake
• IEINCW1 - IE Cold Air Intake System For VW MQB Tiguan 2.0T
• IEINCV1 - IE Performance Intake System For VW Atlas 2.0T
• IEINCC2 - IE 2.0T TSI Cold Air Intake For VW MK5, MK6 GTI, Jetta, CC & 8P A3
• IEINCB4 - IE 2.0T FSI Cold Air Intake Kit For MK6 Golf R, A3, MK5 GTI, Jetta
• IEINCC4 - IE Gen 3 2.0T/1.8T Cold Air Intake For 2013-2018 MK6 Jetta & GLI
• IEINCJ1 - IE  Carbon Fiber Intake For Audi TTS MK2
• IEINCI4 - IE VW 1.4T Cold Air Intake For VW MK6 Jetta

CTS Turbo is proud to release our high flow Turbo Muffler delete for the Non-MQB Gen3 EA888.3 1.8TSI and 2.0TSI engines with the stock turbo.

The CTS Turbo Muffler delete is a one-piece design CNC constructed from T6 6061 aircraft-grade aluminum and hard anodized to reduce wear.

Our Turbo Muffler delete replaces the restrictive, power-robbing OEM Turbo Muffler, which is designed to reduce turbocharger harmonic noise.  By removing the restriction you gain 6-7HP and improve the throttle response!

Our kit installs in 30 minutes with hand tools, fits perfectly and looks great.

For those of you that want optimal power and boost response, the CTS Turbo Gen3 TSI Turbo Muffler Delete is your answer.

NOTE: compatible only with factory Garrett/Honeywell MGT1752S turbo on EA888.3 TSI (turbocharger OE part number 06K145874)

Compatible with factory and CTS Turbo outlet pipes.

NOT FOR MQB VEHICLES!

Fitment:

• Volkswagen Beetle (MK2) Gen3 ONLY
• Volkswagen Jetta (MK6) 1.8TSI & GLI 2.0T (2013.5-2018)
• Volkswagen Scirocco (MK3) Gen3 ONLY
• Volkswagen Passat 1.8TSI & 2.0TSI (B7) Gen3 ONLY