MK7.5 GTI (2017+) - Integrated Engineering - Supernova - Eibach
DESCRIPTION
CTS Turbo is proud to release our 3.0T Supercharger Pulley Upgrade for the Gen 2 3.0T, commonly found in late 2016-2018 B8.5 Audi S4/S5 as well as A6, A7, Q5, SQ5 and Q7
THIS IS THE BOLT-ON STYLE PULLEY KIT. CHECK ON YOUR CAR FOR COMPATIBILITY.
CTS pulley is a smaller diameter than stock. Stock pulley size is 63.25, the CTS pulley is 57.3mm; this will increase the speed at which the supercharger spins, increasing the boost pressure output. Increased boost pressure in conjunction with upgraded ECU software results in a dramatic increase in horsepower and torque throughout the entire powerband. This will not increase stress or excessive wear on supercharger or engine components.
NOTE: CTS 3.0T Supercharger Pulley Upgrade must be used with appropriate “Stage 2” performance software.
Stage 2+ performance software (not included) will allow you to achieve maximum boost and power from your 3.0T while safely optimizing air-fuel ratios, timing, and boost pressure bleed off.
Most Stage 2+ software tunes are compatible with this kit.
Product Details
- Made in house at CTS Turbo in Canada
- Precision CNC machined from billet ASI303 stainless steel – best on the market! No other pulley manufacturer uses this steel.
- OEM-spec honing and tolerances
- Boost increased from stock 11psi to 15psi, boost holds steady all the way up to redline
- Nitride coated for long-lasting OEM looking finish
- Includes belt and bolts required for install
- Stock Size: 63.25mm, CTS Size: 57.3mm
Fitment:
- 2016-2018 B8.5 Audi S4, S5, Q5, SQ5 with 3.0T SUPERCHARGED engine
- 2016+ C7.5 Audi A6, A7 with 3.0T SUPERCHARGED engine
- Late Audi Q7 with 3.0T SUPERCHARGED engine
LEADING FEATURES
- Required for IE TrueFlex MQB tunes
- Allows for instant adjustments from 91 pump to full E85
- Harness for VW MK7 & Audi 8V EA888.3 engines
- Sends sensor data in real-time to IE ECU calibrations
- Includes everything needed to install
OVERVIEW
This plug and play harness kit is required for IE TrueFlex ECU Tunes for VW and Audi MQB Gen 3 engines. This includes everything necessary for the flex-fuel sensor to send real-time data from your fuel system to the ECU and adjust for any content mix from 91 pump to full E85 automatically.
Kit includes:
- (1x) IE TrueFlex Wiring Harness
- (1x) 2 amp Fuse
- (1x) Ethanol Sensor
- (2x) Ethanol Sensor Quick Connect Couplers
- (2x) Hose Clamps
INSTALLATION
This harness kit is fully assembled to proper lengths and includes everything needed to install in a clean and factory-like install. Disconnecting and cutting of factory soft fuel lines is required and should be completed with great care or by a professional.
TrueFlex is currently available for 2015-2018 MK7 GTI & A3 2.0T W/IS38. Stage 1 & 2, Golf R/S3, and 2019+ model years are coming soon!
UPGRADE YOUR PIPES
This charge pipe upgrade Kit for 2.0T and 1.8T MK7/8V TSI engines includes two quality silicone intercooler inlet/outlet hoses and four high-strength band clamps for a direct installation. These hoses are a direct replacement for both IE FDS V2 Intercoolers and the stock factory equipped intercooler. Your new charge pipes feature a flow maximized design with no restrictions for optimized airflow.
Manufactured from multi-ply reinforced silicone for long-life and reliability against expansion or stretching under extreme boost pressures from upgraded turbos and tunes. The ends are molded with a inner flat edge that creates a stop for a perfect and easy no-fuss install and increased reliability against hoses popping off or leaking.
INCLUDES
- (1) Inlet silicone charge pipe
- (1) Outlet silicone charge pipe
- (4) Band clamps
FEATURES
- Fits with IE and Stock intercoolers
- Direct bolt-on fitment
- Smooth airflow transitions
- Multi-ply reinforced silicone hoses
- Internal stops for easy and perfect install
EXPLORE WITH CONFIDENCE
Upgrading your IE 5" velocity stack intake with our harsh climate filter kit will further keep your engine safe when traveling on dirt roads, sandy beaches, or anywhere with dusty contaminants in the air.
KIT DETAILS
This complete filter kit uses a 3 step approach to combat harsh climates. The filter has been increased from a 6 pleat construction to 8 pleats to increase cotton density. The cotton pleats are then treated with a penetrating filter oil to further catch and trap particulates. As a final measure, a pre-filter sock adds a final layer of protection over the filter. Together, these 3 barriers offer superior filtration for your intake system over our standard performance air filter.
KIT CONTENTS:
- 1X IE oiled 8 pleat density performance 5" filter
- 1X IE pre-filter intake sock
- 1X Air filter worm clamp
RECHARGING
As the air filter does its job of effectively catching more particulates, eventually it will have to be cleaned and maintained. We recommend washing your cotton filter in water with a little Dawn dish soap, rinsing thoroughly, and allowing it to completely air dry. To replace the oil, any off-the-shelf filter oil kit from your local auto parts supply chain can be used. Do not over-oil the filter, a little goes a long way.
COMPATIBLE INTAKES
Our 5" Harsh Climate Oiled Air Filter & Sock Upgrade Kit is a direct replacement filter for all popular IE air intake kits with a 5" velocity stack.
- IEINCI11 - IE MQB 2.0T/1.8T Gen 3 Cold Air Intake
- IEINCK3 - IE Carbon Fiber Intake System For Audi B9 S4 & S5 3.0T
- IEINCG2A - IE Audi 3.0T Cold Air Intake For B8/B8.5 S4 & B8.5 S5
- IEINCN1 - IE Audi 3.0T Cold Air Intake For C7 A6 & A7
- IEINSG1 - IE Audi 3.0T Cold Air Intake For 8R SQ5 & Q5
- IEINCG1 - IE Audi 2.0T TSI Cold Air Intake For B8/B8.5 A4 & A5
- IEINCK1 - IE Audi B9 A4 & A5 Cold Air Intake
- IEINCW1 - IE Cold Air Intake System For VW MQB Tiguan 2.0T
- IEINCV1 - IE Performance Intake System For VW Atlas 2.0T
- IEINCC2 - IE 2.0T TSI Cold Air Intake For VW MK5, MK6 GTI, Jetta, CC & 8P A3
- IEINCB4 - IE 2.0T FSI Cold Air Intake Kit For MK6 Golf R, A3, MK5 GTI, Jetta
- IEINCC4 - IE Gen 3 2.0T/1.8T Cold Air Intake For 2013-2018 MK6 Jetta & GLI
- IEINCJ1 - IE Carbon Fiber Intake For Audi TTS MK2
- IEINCI4 - IE VW 1.4T Cold Air Intake For VW MK6 Jetta
PRODUCT FEATURES
- Eliminates excessive play from OE rubber bushings
- Greatly Reduces chances of missed shifts
- CNC machined in-house for precise fitment
- Bronze inner bushing to provide smooth pivoting without wear
PRODUCT DETAILS
Say goodbye to mis-shifts and eliminate unnecessary play in your shifter with IE billet shift cable end bushings!
Eliminate unnecessary play in your shifter with these billet shift cable end bushings. These two piece bushings are CNC machined in-house from 6061 aircraft aluminum with a special bronze inner bushing. They directly replace the rubber factory cable bushings that deteriorate over time causing excessive play in the shifter. When the factory bushings are worn out, shifts become less precise, causing you to miss shifts. Not only will you be missing shifts but, by not fully engaging gears in the transmission, you can even strip the teeth right off the gears. Includes a total of four bushings.
FITMENT
- VW - Golf R 2012-2012 (MK6) 6 speed transmisison
- VW - GTI 2009 (MK5) 6 speed transmisison
- VW - GTI 2010-2014 (MK6) 6 speed transmisison
- VW - Rabbit 2008-2009 (MK5) 5 speed transmisison
- VW - Jetta 2008-2009 (MK5) 5 speed transmisison
- VW - Jetta GLI 2008-2009 (MK5) 6 speed transmisison
- VW - Jetta GLI 2010-2014 (MK6) 6 speed transmisison
- VW - Jetta GLI 2014-2016 (MK6.5) 6 speed transmisison
Description
- Rotomold polymer for superior heat resistance
- Up to 19HP & 21ft-lbs over stock (with software)
- Flow 37% more than the factory airbox
- Flow 61% more than stock with IE turbo inlet
- Increased turbo & engine sounds
- Maximized turbo & engine efficiency
- Huge 5″ air filter for excellent laminar flow
- Integrated velocity stack for smooth airflow
- High pressure & low pressure air zones
- Designed for stock turbo and hybrids (with IE turbo inlet)
- Factory style mounts for reliable & easy installation
- All stainless hardware
- Multi-ply silicone with stop-flat edges
- High-quality clamps
- Powder-coated aluminum filter plate & velocity stack
- Stainless laser-etched logo plate
A special rotomold process is used to manufacture our premium polymer 3.0T intake airbox. This method leverages complex shapes and angles to maximize internal volume for air supply and smooth flow for a true performance design. This molding style also produces consistent wall thickness, strong corners, and superior heat resistance for a cost-friendly intake without compromises.
The entire intake is designed as a single-piece airbox to offer a seamless and complete look with an above factory quality fit and finish.
Our motorsport-designed velocity stack creates a smooth transition from the large filter area to the turbo inlet with excellent laminar properties. This uniquely engineered detail produces a high inertia flow with reduced drag and power-robbing turbulence.
Adding the optional cast turbo inlet upgrade further reduces significant air restrictions while maintaining the largest size possible from the airbox to the turbocharger. The intake and turbo inlet further increases airflow from 37% (intake only) up to a combined 61% over stock!
Turbo inlet pipe is an optional upgrade and can be purchased with your intake or added at a later date.
The intake and turbo inlet designs offer a straightforward and bolt-in job of available hybrid turbo upgrades. Our turbo-specific CNC-machined and o ring sealed adapters always maintain the largest size possible without introducing flow restrictions. Upgrading to a TTE or Pure Turbo hybrid is easy, simple, and hassle-free.
Hybrid turbo adapter rings are sold separately from the turbo inlet upgrade.
IE 3.0T INTAKE SYSTEM & TURBO INLET PIPE INSTALLED WITH TTE810 TURBO ON WORLD-RECORD 9-SECOND B9 S4
IE’s multi-zone intake design delivers all the performance benefits of an open-filter intake while maintaining protection from hot engine bay air from under the hood. A constant ram air supply is forced in from the grille inlet, while any additional air demands are supplied from the low-pressure zone through the filter plate louvers. This dual-zone approach ensures airflow demands for any power level, even the most extreme builds.
The byproduct of a true performance-designed intake is more than power. Our uniquely engineered velocity stack, pressure zones, and extensive internal volume also work together to release a myriad of turbo spools, engine throttle, and diverter blow-off sounds that transform your S4 or S5 with the under-hood acoustics of a genuine sports car.
3D scanning tools are leveraged to create a high-resolution digital environment. This technology allows IE engineers to use all available space for a complete performance design while ensuring a hassle-free fit and installation.
Our cost-effective intake without compromising quality or performance.
Install your new air intake using basic hand tools in no time. Our thermoplastic intake utilizes factory-style mounts that ensure a perfect and hassle-free fit.
Install time: 20 – 45 minutes
Sale
Product Description:
Eibach’s Pro-Kit Lowering Springs (E10-85-051-05-22) are an essential upgrade component to your vehicles suspension & chassis setup. Please carefully check compatibility, any pre-requisites for suspension setups (including front & rear axle load and electronic dampening setups). Motorsport has always been one of Eibach’s core competencies and the testing ground for numerous innovations. Eibach’s passion for precision is what racing enthusiasts worldwide appreciate.
Technical Information
Eibach Part: E10-85-051-05-22
Range: Pro-Kit
Front Lowering: 15-20mm (Max front axle load: 1070kg)
Rear Lowering: 10mm (Max rear axle load: 930kg)
Axle: Multi-Link Axle, for all standard damping systems
Regular Price:
$580.00
Special Price
$522.00
Sale
- World's leading Performance Suspension Spring System
- Engineered and tested to work perfectly with stock dampers
- First step towards a complete sport suspension system
- Lower center of gravity ? lowers vehicle up to 40 mm
- Lowering = Traction + Attraction
- Progressive spring design
- Performance handling
Regular Price:
$515.00
Special Price
$464.00
- World's leading Performance Suspension Spring System
- Engineered and tested to work perfectly with stock dampers
- First step towards a complete sport suspension system
- Lower center of gravity ? lowers vehicle up to 40 mm
- Lowering = Traction + Attraction
- Progressive spring design
- Performance handling
Sale
Eibach PRO-KIT Performance Springs
World‘s leading Performance Suspension Spring System
Regular Price:
$633.00
Special Price
$570.00
