MK7 GTI (2014+) - Forge Motorsports - IPE - VW Central - Flow Designs - INA

DETAILS

Our adjustable side skirt splitter winglets will bolt directly onto our MK7 Golf GTI side skirt splitters thanks to the pre-pressed in threaded brass fittings on our side skirt splitters. Fitting kit is provided to ensure perfect fitment and can be adjusted to your liking. Adjustments can be made anywhere between 5mm-20mm on each side increasing the overall width up to 40mm!

The Volkswagen MK7 Golf GTI body kit range shares the same durability and technology as our renowned VA WRX, i30N and Ford Focus RS line up which is trusted by car enthusiasts worldwide.

MK7 Golf GTI side skirt splitters sold separately. 

---

VOLKSWAGEN MK7 GOLF GTI SIDE SKIRT SPLITTER WINGLETS KIT INCLUDES:

• Volkswagen MK7 Golf GTI adjustable side skirt splitter winglets (pair)
• x2 Flow Designs stickers
• Fitting kit

VOLKSWAGEN MK7 GOLF GTI SIDE SKIRT SPLITTER WINGLETS MATERIAL & FINISH:

• 4.5mm thick textured ABS 
• Scratch resistant textured ABS plastic

Volkswagen MK7 Golf GTI Adjustable Rear Spat Winglets (Pair) Details: The Flow Designs splitter set is the best exterior mod for your VW MK7 Golf GTI! With front & side splitters & rear valance, Flow Designs offer the strongest splitters on the market. Easy install & perfect fitment guaranteed, with Australia-wide & international shipping on all products. VW MK7 Golf GTI Rear Winglets are only compatible with Flow Designs MK7 GTI rear spats only which are designed to be an adjustable direct bolt-on accessory. Adjustable anywhere between 0mm - 20mm on each side increasing the overall width up to 40mm. Rear Spats sold separately. Kit Includes: Adjustable Rear Spat Winglets (Pair) 2 Flow Designs Stickers Fitting kit Material: 4.5mm thick ABS plastic Finish: Scratch resistant textured ABS plastic

Volkswagen MK7 Golf GTI Front Splitter Reinforcement Bar Details: The Flow Designs splitter set is the best exterior mod for your VW MK7 Golf GTI! With front & side splitters & rear valance, Flow Designs offer the strongest splitters on the market. Easy install & perfect fitment guaranteed, with Australia-wide & international shipping on all products. Front Splitter sold separately. Kit Includes: Bumper reinforcement bracket 2 Flow Designs stickers Fitting kit CNC engraved logo and features, hand polish and packed all in Melbourne's outer east.

MK7

MK7 Golf/GTI/Golf R 8V Audi A3/S3 MK3 Audi TT/TT-S

Product Description

This is a direct replacement for Part Number 06H 131 111. - It will fit EA888 Gen 3 engine with IHI Turbo IS20 IS38

On a 2.0L Porsche Macan, this muffler delete gave an additional 10bhp during dyno tests.

Forge has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (TSI) (EA888 engine). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.

https://cdn.shopify.com/s/files/1/0019/9858/5926/files/Window_Vent_Instructions.pdf

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

Product Description

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team for the EA888 TSI vehicles, the Forge turbo blanket is designed to assist in the protection and prolonged life of the engine components.

·       Stainless Steel Rivets
·       Stainless Steel Fasteners
·       Carbon fabric Outer Shell
·       Calcium Magnesium Silicate Wool constructed Inner Core
·       High temperature silica fabric

The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket.

Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers:

• T4
• T5
• T25
• The Garrett GTX28 and GTX30 Range
• Borg Warner EFR6258

Interior Surface:

·       Max Temperature Rating: 2300°F/1260°C
·       Continuous Use Limit: 1832°F1000°C

Exterior Surface:

·       Direct Contact Limit: 1800°F/982°C
·       Radiant Heat Limit: 2500°F/1371°C

Complimentary Products

FAQ HOW IS YOUR SPLITTER SO STRONG? Each splitter is developed to become an integral part of your stock body kit, giving it unrivalled rigidity and strength so it can absorb scrapes and protect your bumper. WHY DO YOU USE POLYETHYLENE COMPOSITE FOR YOUR PRODUCTS? Strong, impact-resistant, doesn't corrode or chip, and has excellent abrasion resistance (eg. scraping on driveways!) WHAT ABOUT CARBON FIBRE? As strong and light as carbon fibre is, it cracks on impact or when under load and/or stress. Clearcoat will eventually fade or crack, becoming undesirable. USE OF ABS PLASTIC Please note that although all our precision-made ABS accessories are extremely strong and durable, they do not hold the same shatterproof label as our 10mm thick polyethylene composite splitters. The accessories are manufactured in ABS with the intention that they will be lighter, bolt-on attachments that will improve aesthetics and are easily replaceable if they become damaged from varying road conditions.