Jetta

For EA888.1 Gen 1 TSI models (2009-2013) - Mandrel bent aluminum piping with black powder coating - CNC machined MAP flange - DV relocation/noise pipe bung - 4 Ply silicon connectors with stainless steel clamps - Integrated water methanol bung with plug - Stainless steel clamps

Black anodized for stealth/oem type appearance CNC machined from 6061 Aluminium Brass plug included with manifold plug O-rings included for great seal Manifold plug can double as boost tap

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

Stop missing shifts and your friends will stop laughing at you.

Eliminate free-play and slop in your factory shifter bracket by replacing soft factory rubber bushings.

Keep your shifts crisp and smooth; and stay ahead of the pack!

Kit includes:

3 x shifter bracket bushings (upper and lower halfs)

This part fits the following transmissions:

MK3: 02A ONLY

MK4: 02J, 02M

MK5: 02Q

MK6: 02Q

MK7: 6MT

The engineering on Volkswagen has never fell short, however many models are still issued with only one low output halogen reverse light from factory. After months of testing various manufacturers, a multitude of knock off ‘Cree’ and ‘OSRAM’ LEDs, we are proud to announce our own, High Output ‘Remnant Series’, Reverse LED which utilises Samsung LED Chips.

Audi	TT	MK2 (2008-2015)	2.0 TSI
Audi	A3	8P (2009-2013)	2.0 TSI (FWD)
Volkswagen	Tiguan	(2009-2011)	2.0 TSI
Volkswagen	Tiguan	(2012+)	2.0 TSI
Volkswagen	Jetta	MK5 (2010)	2.0 TSI
Volkswagen	Jetta	MK6 Sedan (2011-2017)	2.0T GLI
Volkswagen	Jetta	MK6 Sportwagen (2010-2017)	1.8TSI/2.0TSI
Volkswagen Volkswagen	Jetta Golf/GTI/Rabbit	MK6 Sedan (2014-2017) MK5 (2009)	1.8TSI/2.0T GLI 2.0 TSI
Volkswagen	Golf/GTI/Rabbit	MK6 (2010-2014)	2.0T
Volkswagen	CC	(2009+)	2.0 TSI
Volkswagen	Beetle	Beetle (2012+)	2.0 TSI

The Mk5/Mk6 ConsolePod™ holds two (2) 2” or 2 1/16” (52mm) gauges and mounts on underside of the center console. Made with a low-gloss finish, the ConsolePod is uniquely designed to allow you to use the storage compartment 12V power socket and angles the gauges upward towards the driver. The ConsolePod can be used for both LHD and RHD cars and comes with split loom tubing to cover and protect the gauge wires.

PRODUCT FEATURES

• Eliminates excessive play from OE rubber bushings
• Greatly Reduces chances of missed shifts
• CNC machined in-house for precise fitment
• Bronze inner bushing to provide smooth pivoting without wear

PRODUCT DETAILS

Say goodbye to mis-shifts and eliminate unnecessary play in your shifter with IE billet shift cable end bushings!

Eliminate unnecessary play in your shifter with these billet shift cable end bushings. These two piece bushings are CNC machined in-house from 6061 aircraft aluminum with a special bronze inner bushing. They directly replace the rubber factory cable bushings that deteriorate over time causing excessive play in the shifter. When the factory bushings are worn out, shifts become less precise, causing you to miss shifts. Not only will you be missing shifts but, by not fully engaging gears in the transmission, you can even strip the teeth right off the gears. Includes a total of four bushings.

FITMENT

• VW - Golf R 2012-2012 (MK6) 6 speed transmisison
• VW - GTI 2009 (MK5) 6 speed transmisison
• VW - GTI 2010-2014 (MK6) 6 speed transmisison
• VW - Rabbit 2008-2009 (MK5) 5 speed transmisison
• VW - Jetta 2008-2009 (MK5) 5 speed transmisison
• VW - Jetta GLI 2008-2009 (MK5) 6 speed transmisison
• VW - Jetta GLI 2010-2014 (MK6) 6 speed transmisison
• VW - Jetta GLI 2014-2016 (MK6.5) 6 speed transmisison

Dual port boost tap allows for multiple boost references CNC machined from 6061 Aluminium Brass plug included

The CTS Turbo TSI Turbo Outlet Pipe (TOP) is designed to replace the narrow 'pancake' pipe that comes as factory equipment on your vehicle. Our Turbo Outlet Pipe features 2.25" diameter aluminum tube for optimized flow. The CNC machined billet mating flange makes connecting this TOP to your FMIC literally a snap. The billet anodized turbo to TOP connector, 2.25" coupler and premium clamps top this package off. If you're looking for a simple bolt on modification that will optimize flow and increase power, then this part is for you.