Jetta - CTS Turbo - New South Performance - Integrated Engineering - SuperPro - P3 Cars - Whiteline

For EA888.1 Gen 1 TSI models (2009-2013) - Mandrel bent aluminum piping with black powder coating - CNC machined MAP flange - DV relocation/noise pipe bung - 4 Ply silicon connectors with stainless steel clamps - Integrated water methanol bung with plug - Stainless steel clamps

Black anodized for stealth/oem type appearance CNC machined from 6061 Aluminium Brass plug included with manifold plug O-rings included for great seal Manifold plug can double as boost tap

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

Stop missing shifts and your friends will stop laughing at you.

Eliminate free-play and slop in your factory shifter bracket by replacing soft factory rubber bushings.

Keep your shifts crisp and smooth; and stay ahead of the pack!

Kit includes:

3 x shifter bracket bushings (upper and lower halfs)

This part fits the following transmissions:

MK3: 02A ONLY

MK4: 02J, 02M

MK5: 02Q

MK6: 02Q

MK7: 6MT

Audi	TT	MK2 (2008-2015)	2.0 TSI
Audi	A3	8P (2009-2013)	2.0 TSI (FWD)
Volkswagen	Tiguan	(2009-2011)	2.0 TSI
Volkswagen	Tiguan	(2012+)	2.0 TSI
Volkswagen	Jetta	MK5 (2010)	2.0 TSI
Volkswagen	Jetta	MK6 Sedan (2011-2017)	2.0T GLI
Volkswagen	Jetta	MK6 Sportwagen (2010-2017)	1.8TSI/2.0TSI
Volkswagen Volkswagen	Jetta Golf/GTI/Rabbit	MK6 Sedan (2014-2017) MK5 (2009)	1.8TSI/2.0T GLI 2.0 TSI
Volkswagen	Golf/GTI/Rabbit	MK6 (2010-2014)	2.0T
Volkswagen	CC	(2009+)	2.0 TSI
Volkswagen	Beetle	Beetle (2012+)	2.0 TSI

The Mk5/Mk6 ConsolePod™ holds two (2) 2” or 2 1/16” (52mm) gauges and mounts on underside of the center console. Made with a low-gloss finish, the ConsolePod is uniquely designed to allow you to use the storage compartment 12V power socket and angles the gauges upward towards the driver. The ConsolePod can be used for both LHD and RHD cars and comes with split loom tubing to cover and protect the gauge wires.

Dual port boost tap allows for multiple boost references CNC machined from 6061 Aluminium Brass plug included

The CTS Turbo TSI Turbo Outlet Pipe (TOP) is designed to replace the narrow 'pancake' pipe that comes as factory equipment on your vehicle. Our Turbo Outlet Pipe features 2.25" diameter aluminum tube for optimized flow. The CNC machined billet mating flange makes connecting this TOP to your FMIC literally a snap. The billet anodized turbo to TOP connector, 2.25" coupler and premium clamps top this package off. If you're looking for a simple bolt on modification that will optimize flow and increase power, then this part is for you.

ADD POWER, TORQUE, AND SOUND

The massive 5” velocity stack and ram-air designed IE Cold Air Intake Kit delivers the most air and horsepower possible. Quickly add horsepower, torque, and aggressive engine and turbo sound to your VW or Audi 2.0T TSI (Gen1/2) engine. 

LEADING FEATURES

• INCREASED HORSEPOWER & TORQUE
• ENHANCED ENGINE, TURBO, & BLOW-OFF SOUND
• HIGH-FLOW BELLMOUTH
• MASSIVE OVER-SIZED AIR FILTER
• BLACK POWDER COAT FINISH
• EASY INSTALL WITH NO MODIFICATIONS
• USES FACTORY MOUNTING GROMMETS & HARDWARE
• HEAT SHIELDING & DIRECTED AIR FLOW
• REINFORCED SILICONE HOSES
• FITS DSG AND MANUAL TRANSMISSIONS

YOUR BUILD DESERVES THE BEST

Feed your 2.0T TSI GTI, Jetta, GLI, CC, or A3 with a supply of cold air with this direct-fit high-flow cold air intake kit. This intake features a generously-sized inlet pipe that connects to the OE mass air flow (MAF) sensor. The MAF sensor receives high-velocity air fed directly from a 5" bellmouth. Our high-flow bellmouth is neatly housed in a heat shield, which separates the air filter from the hot under-hood air, allowing only cold air to be drawn into the turbo inlet directly from the front of the car.

STOCK-LIKE DIRECT FIT

This air intake kit provides all the necessary piping and couplers to plumb the intake system from the turbo to the MAF and then to the heat shield. The heat shield installs using the OE grommets for easy maintenance and reliable mounting with no rubbing or interference with other factory parts.

HIGH-FLOW VELOCITY STACK

The air intake utilizes a high-flow bellmouth behind the air filter to deliver as much air as possible. This bellmouth design increases the air velocity to the MAF and pulls cold air equally from all directions into the filter. This bellmouth is securely fastened to the heat shield as a clean pass-through providing a solid mount for the air filter and turbo inlet pipe. You have no worry about the intake pipe moving around and causing damage unlike other intake kits on the market, which simply clamp the filter onto the end of the inlet pipe or MAF. Furthermore, the bellmouth opening allows for a filter with a very large surface area that can support any horsepower goal. The same filter and bellmouth design have been tested to support over 500HP!

THERMAL BLOCKING HEAT SHIELD

The IE heat shield is designed to create a thermal barrier blocking all of the radiant heat from the engine bay. Only cold air from the front of the vehicle is drawn into the filter from the opening in the radiator support keeping air intake temperatures as cold as possible. This allows factory placement of the intake to be used without placing the filter lower in the vehicle where it can be subjected to engine harming road debris or fluid.

DO YOU NEED AN SAI KIT?

The MK5/MK6 2.0T TSI engine has two different engine codes. CBFA engine codes are equipped from the factory with a secondary air injection (SAI) pump that connects to the factory intake box. These engines require a small breather filter for this SAI line when installing an aftermarket intake. CCTA engine codes do not have this SAI pump and will not require this filter. Identify your engine code using the photos below, and add an SAI filter kit above if needed when ordering your intake.

EASY INSTALLATION

Installation is quick and easy to install with basic tools. The process should take around an hour for most enthusiasts.

CLICK HERE to view and download the Cold Air Intake install guide