Experiencing Misfires on your car? Don't go OEM again!
Upgrade your coilpacks to these sporty, redtop R8 coilpacks! Used on the Audi R8 V8 and V10, these coilpacks offer a stronger spark than factory, reducing troublesome misfire on performance upgraded and tuned VAG vehicles
Buy a set of 4 Now!
The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.
Regular Price: $1,899.00
Special Price $1,769.00
One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.
Regular Price: $184.00
Special Price $179.00
EVAP Crossover Tube Relocation Kit for 2.0T FSI with IE Valve Cover
This recirculating catch can kit has been designed for use with the IE billet valve cover (IE part number: IEBAVC5) as a simple install solution for your billet valve cover and catch can.
IE billet valve cover sold separately.
Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!
IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.
Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.
This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.
EVAP CROSSOVER TUBE RELOCATION KIT
The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11
CATCH CAN KIT FOR BILLET VALVE COVER
The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3
*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.
Regular Price: $769.00
Special Price $692.00
Modernise your vehicle by upgrading the radio to an RCD330G+ with it's built in bluetooth, Apple CarPlay, Mirrorlink & Android Auto.
Compatibility:
Take advantage of the latest CarPlay functionality by upgrading your iPhone to iOS 14.
Package Contents:
Tech Specs:
Additional Information:
Please note for vehicles prior to 2008, you will need to upgrade your CAN Gateway to prevent battery drain.
Will NOT work on an VW Polo 6C MQB
Regular Price: $699.00
Special Price $639.00
Retain your VW MK5's 8-button steering wheel controls after installing an RCD330G with this plug and play harness.
This harness is designed to retain the use of every button on your factory steering wheel which will communicate with your RCD330G headunit.
Simply plug in this harness directly into the back of your RCD330G headunit, followed by your vehicles factory quadlock.
Compatible with:
- Golf Mk5
- Jetta Mk5
- Passat B6
Radio models:
- RCD330
- RCD340
- RCD360
- RNS510
- RCD510
Regular Price: $79.00
Special Price $65.00