Passat - Leyo Motorsport - Integrated Engineering - Eibach

The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.  

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

EVAP Crossover Tube Relocation Kit for 2.0T FSI with IE Valve Cover

This recirculating catch can kit has been designed for use with the IE billet valve cover (IE part number: IEBAVC5) as a simple install solution for your billet valve cover and catch can. 
IE billet valve cover sold separately. 

Product Features

Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!

PRODUCT DETAILS

IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.

MACHINED DESIGN

Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.

FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY

This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.

PRODUCT FEATURES

• Replaces factory plastic valve cover
• Uses factory valve cover gasket
• In-house CNC machined from aluminum
• Includes o ring sealed matching billet oil cap
• -10AN breather outlet for catch can setups

ADDITIONAL PARTS REQUIRED

EVAP CROSSOVER TUBE RELOCATION KIT

The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11

CATCH CAN KIT FOR BILLET VALVE COVER

The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3

VEHICLE FITMENT

• Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
• Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
• Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
• Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
• VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
• VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
• VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
• VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*

*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.

Description:

In the world of VW, the R32 with the iconic VR6 engine has achieved cult-like status. Leyo Motorsport has over the years gained enough experience to now touch an icon. 

Air flowing through the OE air scoop is greeted by an enlarged high flow air filter and quickly fed into the engine, assisting power gains across the rev range especially in the higher rpm’s whether you on stock or tuned ECU. 

Excessive heat from the engine bay is blocked by the heat shield.

LEYO Cold Air Intake System guarantees greater air induction volume, colder intake air temperature and smoother air flow for superior power gain. LEYO Cold Air Intake System was designed with the ultimate goal of maximum power gain. 

Installation is simple and straight forward, no fabrication required.

*This product is only for use on the race track.

Specifications:

• OEM fitment requires no fabrication.

• 3.5’inch diameter for greater air induction.

• Track and dyno proven for greater   horsepower gain.

• Direct bolt on & easy installation.

Description:

Made from T6061 billet aluminum, LEYO DSG Oil Filter Housing not only adds aesthetic appeal to the engine bay, but specially designed fin also provides effective heat dispersion for the DSG under load. Heat resistant to prolong optimum operational temperature.

*Only fits 6 speed DSG DQ250 wet.

Specifications:

• T6061 Billet aluminum construction.

• Hard coat anodized finish for impeccable appearance and heat resistance.

• Promotes oil heat dispersion.

Description:

Eibach performance lowering springs Pro-Kit

The absolute top seller. The number one choice of automotive enthusiasts worldwide. The Eibach Pro-Kit springs are the ideal solution for your series vehicle . The proven spring system maximizes the handling of your vehicle and ensures a sporty look .

The Pro-Kit lowers the center of gravity of your vehicle and reduces the rebound during accelerating, reduces the tendency of the body to roll when cornering and the dipping when braking drives.

The Eibach Pro-Kit in combination with appropriate wheels and tires is the guarantee of success for optimal performance. The lowering with Eibach Pro-Kit springs reduces the unnecessary distance between the tires and the wheelhouse and gives the vehicle a sporty look.

Eibach Pro-Kits are designed by Eibach's chassis engineers and test experts designed to deliver a combination of sporty looks and performance without sacrificing safety or ride quality.

A leading performance suspension spring system worldwide
tested for the combination with stock and retrofit dampers
First step towards a complete sport suspension system
Lower center of gravity – lowers vehicle up to 40 mm (depending on the vehicle)
Spring design for traction and attraction
Progressive spring design
Performance Handling
ABE or parts certificate

Compatible Vehicles: