Passat - Integrated Engineering - Genuine VW - VW Central

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers.

TURBO INLET PIPE FEATURES

• Greatly improves air-flow to turbocharger
• Constant high-flow inner diameter
• Easy install, no modifications necessary
• Long life cast aluminum alloy
• In-house CNC machined for perfect fitment
• No leak o ring seal to turbocharger 
• Outflows stock inlet by 110CFM

IS YOUR STOCK INLET ROBBING POWER?

The factory installed plastic turbo inlet found installed on your VW or Audi Gen 3 1.8T or 2.0T TSI engine is adequate enough for stock cars with factory hardware and ECU calibrations. However, the necked down design becomes a major flow restriction when ran with power upgrades such as cold air intakes, intercoolers, downpipes, and ECU upgrades. 

UPGRADE YOUR TURBO INLET PIPE

The IE Turbo Inlet Pipe helps you to get the most out of your IS38 or IS20 turbo and power upgrades by removing the factory flow restriction. The cast aluminum design allows for a constant diameter elbow increasing efficiency from the intake to the turbo without the bottleneck design of the factory unit.

HORSEPOWER RESULTS

Dyno graph tested on a 2019 GTI with Stage 2 hardware & software on 93 octane

EASY INSTALLATION

Your new turbo inlet pipe has been in-house CNC machined and includes all required hardware to allow for a perfect and easy installation. View and download the install guide here (coming soon).

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers. 

VEHICLE APPLICATIONS

• Audi - A3 2015+ 8V 1.8T & 2.0T engines
• Audi - S3 2015+ 8V 2.0T engine
• Audi - TT 2016+ 8S 2.0T engine
• Audi - TTS 2016+ 8S 2.0T engine
• VW - Golf R 2015+ MK7 2.0T engine
• VW - GTI 2015+ MK7 2.0T engine
• VW - Golf/Alltrak 2015+ MK7 1.8T & 2.0T
• VW - Passat 2013+ B8 1.8T & 2.0T (EA888 Gen 3) engines
• VW - Tiguan 5N 2017+ 2.0T (EA888 Gen 3) engine

Genuine Volkswagen USB AUX Switch for CarPlay & Auto Android Adapter Plug Socket

This USB/AUX Adapter is designed for MIB 2 & MIB 2.5 Radio Control Units. This adapter is required for Pre-2016 Vehicles to allow CarPlay and Auto Android connectivity.

Compatible with:

Most commonly used to eliminate battery drain issues in Pre-2009 model Volkswagen cars when upgrading the radio to a later model such as the RNS510, RCD510 ,RCD330, RCD340 etc.

The Canbus Gateway Module, will require coding using software such as VCDS or OBDII. 

Installation instructions: https://www.my-gti.com/2296/can-bus-gateway-removing-installing-and-upgrading-volkswagen-golf

Experiencing Misfires on your car? Don't go OEM again!
Upgrade your coilpacks to these sporty, redtop R8 coilpacks! Used on the Audi R8 V8 and V10, these coilpacks offer a stronger spark than factory, reducing troublesome misfire on performance upgraded and tuned VAG vehicles

Buy a set of 4 Now!

Experiencing Misfires on your car? Don't go OEM again!
Upgrade your coilpacks to these sporty, redtop R8 coilpacks! Used on the Audi R8 V8 and V10, these coilpacks offer a stronger spark than factory, reducing troublesome misfire on performance upgraded and tuned VAG vehicles

Buy a set of 4 Now!

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.  

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

EVAP Crossover Tube Relocation Kit for 2.0T FSI with IE Valve Cover

This recirculating catch can kit has been designed for use with the IE billet valve cover (IE part number: IEBAVC5) as a simple install solution for your billet valve cover and catch can. 
IE billet valve cover sold separately. 

 

Product Features