.: R Models - IROAD - Turbosmart - VW Central - Flow Designs

Turbosmart's new Kompact Shortie Blow-Off Valve for VAG 2.0 TSI engines takes performance to the next level. These valves are a high performance replacement for the standard diverter valve fitted to the current 2.0 TSI range. Unlike the standard valve's plastic construction, they are machined from aircraft grade aluminium, and bolt straight up to the factory location, offering all the technology from Turbosmart's race-bred BOV range in an OEM-replacement package. The Dual Port offers a 50/50 split between recirculating and vent-to-atmosphere, for quiet operation at low boost, and the high performance sound associated with vent-to-atmosphere BOVs at higher boost. The Dual Port also recirculates enough air to keep the car's ECU happy. Turbosmart's Kompact Shortie does not leak, bleed boost pressure or struggle with increased boost on tuned vehicles. It also completely eliminates compressor surge, allowing the turbo to operate to its full potential, and for longer.

Turbosmart's new Kompact Shortie Blow-Off Valve for the Mk7 takes performance to the next level. These valves are a high performance replacement for the Golf's standard diverter valve. Unlike the standard valve's plastic construction, they are machined from aircraft grade aluminium, and bolt straight up to the factory location, offering all the technology from Turbosmart's race-bred BOV range in an OEM-replacement package. The Plumb Back is a 100% recirculating blow-off valve, routing all vented air back into the intake. This valve operates at a similar level of volume to the standard valve, avoiding unwanted attention. Turbosmart's Kompact Shortie does not leak, bleed boost pressure or struggle with increased boost on tuned vehicles. It also completely eliminates compressor surge, allowing the Golf's turbo to operate to its full potential, and for longer.

The Kompact EM series combines world leading electronics and 20 years of blow off valve technology together to provide rapid response.

• Plug and play compatability
• 400% stronger than the OE Diverter Valve
• Designed to handle boost pressure up to 30PSI
• Ideal for lightly modified vehicles

MK7 Golf/GTI/Golf R 8V Audi A3/S3 MK3 Audi TT/TT-S

Experiencing Misfires on your car? Don't go OEM again!
Upgrade your coilpacks to these sporty, redtop R8 coilpacks! Used on the Audi R8 V8 and V10, these coilpacks offer a stronger spark than factory, reducing troublesome misfire on performance upgraded and tuned VAG vehicles

Buy a set of 4 Now!

Experiencing Misfires on your car? Don't go OEM again!
Upgrade your coilpacks to these sporty, redtop R8 coilpacks! Used on the Audi R8 V8 and V10, these coilpacks offer a stronger spark than factory, reducing troublesome misfire on performance upgraded and tuned VAG vehicles

Buy a set of 4 Now!

Product Details The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation. Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle! You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device. In house designed and built in the USA, our Boost Tap includes the following: Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap 3 Vacuum Ports with 1/4" Hose Barb Fittings 3 Vacuum Set Screws Medium Strength Thread Lock OEM Securing Clip Manifold Pierce Alignment Tools In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!

DETAILS

Protect your bumper from scrapes or kerbing with our MK7 Golf R front lip splitter! All our lip splitters are made from a thick polyethylene composite, making it the strongest product of its type on the market, watch our stress test to see how durable our splitters are. Each splitter is model specific in its development and design to ensure perfect fitment. The entire production process is done is our Bayswater factory making us proudly Australian made and owned.

We offer fast Australia-wide and international shipping for all our products - join the worldwide Flow Family today!

MK7 Golf R front extensions and MK7 Golf R front winglets sold separately. 

---

KIT INCLUDES

• MK7 Golf R front lip splitter
• Pre-mounted adjustable Aerospacers
• Stainless steel crossbar mounts (pair: left & right)
• 2 Flow Designs stickers
• Fitting kit

MATERIAL & FINISH

• 10mm thick polyethylene composite, bevelled edges
• Hand polished satin black

DETAILS

Protect your body work from scrapes or kerbing with our MK7 Golf R side skirt splitter! All our lip splitters are made from a thick polyethylene composite, making it the strongest product of its type on the market, watch our stress test to see how durable our splitters are.

Installation is simple with pre-drilled holes so there is no guesswork. We have machined out a pocket for the OEM Golf side skirt to sit snug into - this way our side skirt splitters will mount up flush with the stock body kit once installed on the car.

We also have designed other visual prompts to show where the side skirt splitter aligns with the OEM side skirt and Golf R chassis.

The pre-installed brass thread allow for installation of our MK7 Golf R adjustable side winglets which are sold separately as a bolt-on accessory to suit our side skirt splitters. 

---

KIT INCLUDES

• MK7 Golf R side skirt splitters (pair)
• 2 Flow Designs stickers
• Fitting kit

MATERIAL & FINISH

• 10mm thick polyethylene composite, bevelled edges
• Hand polished satin black