This is a direct replacement for Part Number 06H 131 111. - It will fit EA888 Gen 3 engine with IHI Turbo IS20 IS38
On a 2.0L Porsche Macan, this muffler delete gave an additional 10bhp during dyno tests.
Forge has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (TSI) (EA888 engine). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.
Experiencing Misfires on your car? Don't go OEM again! Upgrade your coilpacks to these sporty, redtop R8 coilpacks! Used on the Audi R8 V8 and V10, these coilpacks offer a stronger spark than factory, reducing troublesome misfire on performance upgraded and tuned VAG vehicles
Experiencing Misfires on your car? Don't go OEM again! Upgrade your coilpacks to these sporty, redtop R8 coilpacks! Used on the Audi R8 V8 and V10, these coilpacks offer a stronger spark than factory, reducing troublesome misfire on performance upgraded and tuned VAG vehicles
Product Details
The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation.
Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle!
You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device.
In house designed and built in the USA, our Boost Tap includes the following:
Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap
3 Vacuum Ports with 1/4" Hose Barb Fittings
3 Vacuum Set Screws
Medium Strength Thread Lock
OEM Securing Clip
Manifold Pierce Alignment Tools
In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!
MK7 Golf R Flow-Lock rear diffuser OR rear aero valance (please select)
Please select your choice of WITHOUT accessories or WITH all accessories in the MK7 R range (front extensions, front winglets, side winglets, rear winglets)
The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team for the EA888 TSI vehicles, the Forge turbo blanket is designed to assist in the protection and prolonged life of the engine components.
The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it shouldnot be routinely removed as you will likely damage the blanket.
Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers:
T4
T5
T25
The Garrett GTX28 and GTX30 Range
Borg Warner EFR6258
Interior Surface:
· Max Temperature Rating: 2300°F/1260°C · Continuous Use Limit: 1832°F1000°C
Exterior Surface:
· Direct Contact Limit: 1800°F/982°C · Radiant Heat Limit: 2500°F/1371°C
FAQ
HOW IS YOUR SPLITTER SO STRONG?
Each splitter is developed to become an integral part of your stock body kit, giving it unrivalled rigidity and strength so it can absorb scrapes and protect your bumper.
WHY DO YOU USE POLYETHYLENE COMPOSITE FOR YOUR PRODUCTS?
Strong, impact-resistant, doesn't corrode or chip, and has excellent abrasion resistance (eg. scraping on driveways!)
WHAT ABOUT CARBON FIBRE?
As strong and light as carbon fibre is, it cracks on impact or when under load and/or stress. Clearcoat will eventually fade or crack, becoming undesirable.
USE OF ABS PLASTIC
Please note that although all our precision-made ABS accessories are extremely strong and durable, they do not hold the same shatterproof label as our 10mm thick polyethylene composite splitters. The accessories are manufactured in ABS with the intention that they will be lighter, bolt-on attachments that will improve aesthetics and are easily replaceable if they become damaged from varying road conditions.
Please note you are receiving a special price when you purchase the MK7 R complete body kit splitter set.
Please select the rear option you want in your kit: Flow-Lock rear diffuser or rear aero valance
The Flow Designs splitter set is the best exterior mod for your VW MK7 Golf R! With front & side splitters & rear valance, Flow Designs offer the strongest splitters on the market. All our splitters are made from a thick polyethylene composite, making it the strongest product of its type on the market, watch our stress test to see how durable our splitters are.
Easy install & perfect fitment guaranteed, with Australia-wide & international shipping on all products.
KIT INCLUDES
V3 front lip splitter & Aerospacers
Stainless steel crossbar mounts (pair: left & right)
V3 side skirt splitters (pair)
Flow-Lock rear diffuser OR Rear aero valance & fairing
V3 rear lip spats/pods (pair)
WITH all accessories package:Adjustable front extensions (pair)
WITH all accessories package:Adjustable front winglets (Pair)
WITH all accessories package:Adjustable side winglets (Pair)
WITH all accessories package:Adjustable rear winglets (Pair)
2 Flow Designs stickers
Fitting kit
MATERIAL & FINISH
Front lip splitter, side skirt splitters, rear aero valance, rear pods/spats: 10mm thick polyethylene composite, bevelled edges
Hand polished satin black
Flow-Lock diffuser fins OR rear fairing: scratch resistant textured ABS plastic