.: R Models - Forge Motorsports - IPE - Eibach

Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

Product Description

This will replace OEM part numbers 06H 145 710D, 06F 145 710G, & 06H 145 710 C

Forge Motorsport is proud to release the latest version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CJXB, CZPA, and CJXC;US codes CPLA and CPPA) including Golf MK7 R

This valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. It has also been proven in cars running over 600bhp!

This new valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

In The Box:
1 x FMDVMK7R Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker

Product Description

This is a direct replacement for Part Number 06H 131 111. - It will fit EA888 Gen 3 engine with IHI Turbo IS20 IS38

On a 2.0L Porsche Macan, this muffler delete gave an additional 10bhp during dyno tests.

Forge has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (TSI) (EA888 engine). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.

Product Description

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team for the EA888 TSI vehicles, the Forge turbo blanket is designed to assist in the protection and prolonged life of the engine components.

·       Stainless Steel Rivets
·       Stainless Steel Fasteners
·       Carbon fabric Outer Shell
·       Calcium Magnesium Silicate Wool constructed Inner Core
·       High temperature silica fabric

The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket.

Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers:

• T4
• T5
• T25
• The Garrett GTX28 and GTX30 Range
• Borg Warner EFR6258

Interior Surface:

·       Max Temperature Rating: 2300°F/1260°C
·       Continuous Use Limit: 1832°F1000°C

Exterior Surface:

·       Direct Contact Limit: 1800°F/982°C
·       Radiant Heat Limit: 2500°F/1371°C

Complimentary Products

Product Description

THIS PRODUCT DOES NOT FIT LEFT HAND DRIVE VEHICLES

The Forge Motorsport high flow intake hose for the MQB platform 2.0 engines, eliminates the highly restrictive plastic inlet pipe, and replaces it with our smooth bore multi-ply silicone hose which increases air flow, improving efficiency and performance. This equates to increases of up to 10hp which is a remarkable gain for an easy to fit bolt on modification.

⭐ Excellent quality product & easy to fit ⭐

The high flow male alloy coupler is a bayonet type, rotated to the locked position before fixing in place by positioning the hose on the alloy coupler and tightening the hose clamps at both ends of the hose, anchoring the alloy coupler in position to complete the installation.

The Forge silicone hose in this kit has been designed to include an expensive inner liner of modified silicone known as Fluorosilicone.This means the hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) but more importantly for this application, air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically.The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader.

As with all Forge products, this hose comes with a lifetime warranty*

iPE Innotech revolutionizes the Hot-Hatch-Segment with an exhaust system completely made from stainless steel, for the new VW Golf R MK7.

This extremely durable, performance increasing and valve-controlled system brings your new Golf R more than only an exclusive touch.

Our premium-class exhaust system has larger pipes in diameter and an optimized exhaust flow, leading to more performance and improved torque and response.

The system comes standard with chrome silver tips. Different colour tips are available from the drop-down menu.

Please note if you have an MK7.5 Golf R - The link pipe to the muffler is different to the MK7 Golf R. 

DESCRIPTION

1.Improper adjustments made during installation may result in short-term to permanent damages to the iPE exhaust system and/or your vehicle.

iPE will not be held responsible for any damages to the vehicle, and warranties on our products will be voided if the damages occurred due to improper installation.If you have any trouble installing the system please contact your authorized dealer!



2. The manufacturer, importer or dealer shall not be liable for any incidental damage including personal injury or any other damages caused by improper installation or operation of the iPE exhaust system. When installing the iPE exhaust system be careful that the exhaust system does not touch other parts sensitive to high temperature.



3. iPE makes no representation or warranties with regard to damage caused by the improper installation, use and maintenance of the iPE exhaust system. The warranty is limited to defects recognized by our technical department and of normal use only, and excludes items subject to normal wear and tear(gaskets and damping wool). The warranty is voided in case of accidents, modifications, improper or competition uses.



*Actual product may vary due to product enhancement. iPE reserves the right to revise, change, explain the product.

*Cat Pipe/Cat-bypass Pipe ONLY fit with iPE Catback System

iPE Innotech revolutionizes the Hot-Hatch-Segment with an exhaust system completely made from stainless steel, for the new VW Golf R MK7.5

This extremely durable, performance increasing and valve-controlled system brings your new Golf R more than only an exclusive touch.

Our premium-class exhaust system has larger pipes in diameter and an optimized exhaust flow, leading to more performance and improved torque and response.

The system comes standard with chrome silver tips. Different colour tips are available from the drop-down menu.

Please note if you have an MK7 Golf R - The link pipe to the muffler is different to the MK7.5 Golf R. 

DESCRIPTION

The Volkswagen Golf R (Mk7.5) and the other Golf series (GTis and Golf Rs) has been one of the most popular hatchbacks in the car community. The famous EA888 engine is now at its 3rd generation, with its 2.0L turbo-charged engine, it continues to be a car with great tuning potential. The iPE Exhaust system is designed and engineered to enhance gas flow and maximize performance gain by 23HP and 39.2 Nm of torque. Highlighting the angry sound from the EA888 Gen3. This iPE exhaust system is handcrafted with T304 Stainless Steel to reduce weight by 13%(-4.0kg).



iPE Valvetronic system for the Volkswagen Golf R (Mk7.5) allows users to adjust the exhaust note through OBD II Hand Gesture Control Sensor or Bluetooth Remote Control Module. Furthermore, we also offer various motorsport-inspired exhaust tip upgrade options.



Catback Exhaust System:

1. Mid pipe

2. Valvetronic Muffler

3. Chrome Silver tips



Valvetronic Control system:

- Remote Control system

- Hand Gesture Control sensor (Optional)



Exhaust Tip Upgrade Options:

- Chrome Black tips

- Titanium Blue tips

- Carbon Fiber tips