.: R Models - Forge Motorsports - Leyo Motorsport

Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

Description:

For the ultimate driving experience, you need the connection directly at your fingertips. Leyo Motorsport understands that when it comes to perfecting the exit of an apex, gear changes need to be precise and fluently timed. Welcome to the greatest edition and interior modification for you performance vehicle, the Leyo Motorsport Aluminium paddle shifters. Made from 6061 billet aluminium, these shift extensions will be the classiest addition to your interior yet. Available in multiple finishes and coated with a hard anodised finish, Leyo Motorsport have truly delivered on our most in-demand product.

Leyo Motorsport endeavours to get you the purest driving experience by manufacturing products that are race proven with durability in mind. Order today and pursue your very own ultimate driving experience.

Specifications:

• The ultimate addition to your performance vehicle.
• Patented design (Pending).
• Direct OEM bolt-on. Clips right over existing paddle shifters.
• Comes with all components required to get your car looking amazing.
• Ergonomic back CNC surface.
• Scratch Free for your OEM plastics paddle.
• Undergoes 6 stage hand polishing.

Description:

Product Description

This will replace OEM part numbers 06H 145 710D, 06F 145 710G, & 06H 145 710 C

Forge Motorsport is proud to release the latest version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CJXB, CZPA, and CJXC;US codes CPLA and CPPA) including Golf MK7 R

This valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. It has also been proven in cars running over 600bhp!

This new valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

In The Box:
1 x FMDVMK7R Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker

Product Description

This is a direct replacement for Part Number 06H 131 111. - It will fit EA888 Gen 3 engine with IHI Turbo IS20 IS38

On a 2.0L Porsche Macan, this muffler delete gave an additional 10bhp during dyno tests.

Forge has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (TSI) (EA888 engine). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.

Product Description

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team for the EA888 TSI vehicles, the Forge turbo blanket is designed to assist in the protection and prolonged life of the engine components.

·       Stainless Steel Rivets
·       Stainless Steel Fasteners
·       Carbon fabric Outer Shell
·       Calcium Magnesium Silicate Wool constructed Inner Core
·       High temperature silica fabric

The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket.

Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers:

• T4
• T5
• T25
• The Garrett GTX28 and GTX30 Range
• Borg Warner EFR6258

Interior Surface:

·       Max Temperature Rating: 2300°F/1260°C
·       Continuous Use Limit: 1832°F1000°C

Exterior Surface:

·       Direct Contact Limit: 1800°F/982°C
·       Radiant Heat Limit: 2500°F/1371°C

Complimentary Products

Product Description

THIS PRODUCT DOES NOT FIT LEFT HAND DRIVE VEHICLES

The Forge Motorsport high flow intake hose for the MQB platform 2.0 engines, eliminates the highly restrictive plastic inlet pipe, and replaces it with our smooth bore multi-ply silicone hose which increases air flow, improving efficiency and performance. This equates to increases of up to 10hp which is a remarkable gain for an easy to fit bolt on modification.

⭐ Excellent quality product & easy to fit ⭐

The high flow male alloy coupler is a bayonet type, rotated to the locked position before fixing in place by positioning the hose on the alloy coupler and tightening the hose clamps at both ends of the hose, anchoring the alloy coupler in position to complete the installation.

The Forge silicone hose in this kit has been designed to include an expensive inner liner of modified silicone known as Fluorosilicone.This means the hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) but more importantly for this application, air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically.The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader.

As with all Forge products, this hose comes with a lifetime warranty*

Description:

Struggling with the OEM Turbo Valve? Need to add that unique boost pressure sound? Make sure to get your hands on All New Re-Designed Leyo Motorsports latest in-house designed Diverter Valve. Leyo Motorsport Diverter Valve multi piece design is built and engineered to solve the failure issues associated with the OEM solenoid valves and their diaphragm resulting in boost leaks. It is built from 6061 Billet Aluminum with hard coated Anodized finish with an internal serviceable piston based design that provides greater reliability over the OEM as well as quicker throttle and turbo response. All components are made in-house by Japan CNC’s, inspected to 0.01mm tolerance by Japan CMM, laser etched and race proven.

Leyo Motorsport Diverter vavle has a unique and fully tested internal piston compared with other brands in order to get the maximum results in power. We are offering a stronger, more durable and reliable valve compared to the OEM unit. We do have uprated valve spring in stock that is sold separately.

Specifications:

• Made from the highest quality T6061 billet aluminium construction.

• Direct OEM replacement..

• Improved throttle response

• Consistent turbo boost.

• Reduced turbo lag .

• Fully compatible with OE electronics.

• Fully serviceable piston .

• Holds up to 600HP. (with optional uprated spring kit)

* Note : This DV kit comes supplied with BLACK / WHITE / YELLOW Spring. Uprated BLUE / RED Spring is Available for purchase. 

SUGGESTED SPRING INSTALLATION

Above figure is only preference. Please refer vehicle modification needs. 

Description: