Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!

PRODUCT DETAILS

IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.

MACHINED DESIGN

Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.

FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY

This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.

PRODUCT FEATURES

 

• Replaces factory plastic valve cover
• Uses factory valve cover gasket
• In-house CNC machined from aluminum
• Includes o ring sealed matching billet oil cap
• -10AN breather outlet for catch can setups

ADDITIONAL PARTS REQUIRED

 

EVAP CROSSOVER TUBE RELOCATION KIT

The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11

CATCH CAN KIT FOR BILLET VALVE COVER

The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3

 

VEHICLE FITMENT

• Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
• Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
• Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
• Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
• VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
• VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
• VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
• VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*

*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.

DESCRIPTION Direct fit upgrade for the factory BOV on Hyundai i30N Packaged with a blanking plug to switch the unit into pure vent to atmosphere or plumb-back modes All billet CNC construction and attractive anodized finish Manufactured, assembled and validated in-house at Turbosmart HQ A direct fit high performance replacement for the factory all plastic unit, the Turbosmart Kompact BOV suits the Hyundai i30N. The Turbosmart unit is made of billet aerospace grade aluminium with high temperature seals that allows for minimal leakage and a complete seal across the bypass aperture providing as much performance as possible.

INCREASE POWER AND SOUND WITH A COLD AIR INTAKE

The IE Audi B9 A4 & A5 2.0T Cold Air Intake is the perfect addition to any engine bay. Give your Audi added horsepower, torque, snappier throttle response, and an aggressive sound. Typical peak gains from our CAI are roughly 10-20 Horsepower and Torque.

POWER GAINS

The ram air design, velocity stack, and massive 55-inchfilter inlet help deliver the most HP possible from a cold intake system.

Expect peak gains of 10-20+HP/TQ on tuned engines.

INCLUDED IN THE B9 IE CAI KIT

• IE Intake velocity stack & heatshield assembly
• IE Silicone turbo inlet pipe assembly
• IE 5” inlet performance air filter
• IE Turbo heat shield
• All necessary hardware (clamps, nuts, bolts, etc)

INCREASED AIR FLOW

This Intake delivers an impressive flow increase to feed your turbo. More cold air flow means more power; especially during the hot summer months. Ditch your stock restrictive airbox for the IE intake System.

DESIGN DETAILS

IE engineers set out to produce the highest performing cold air intake that looks great and fits like a factory installed part in your A4. The latest in computer design and 3D scanning technology were employed during the development process for a perfect fit and maximum performance. The final product resulted in the greatest performing and best-looking intake available.

HIGH-FLOW VELOCITY STACK

Delivering cold air to your engine is a must for making power. The velocity stack efficiently channels air as quickly as possible into the intake system. The velocity also functions as a solid mount for the air filter which means no intake pipes rattling on heat shields.

CUSTOM HEAT SHIELD

IE uses a three piece heat shield which performs and looks great. It effectively channels cold air from the front of the car to the massive performance filter. Furthermore, it eliminates the induction of hot air found in other locations of the engine bay. A second heat shield is mounted above the turbocharger to further protect against power robbing heat off the exhaust and turbo.

PERFECT FITMENT

This Intake fits B9 Audi A4 and A5 without any modification or installation hassles. The install process is simple and can be done quickly with basic tools. The fact that IE intake utilizes the factory airbox mounts ensures a perfect and hassle free fit. Additionally, the stock rubber mounts allow for engine movement which keeps intake components from getting damaged.

CLASSY AND CLEAN APPEARANCE

Wrinkle black powder coated velocity stack and heat shields result in a sleek and sporty appearance in any engine bay. As a final touch, all IE heat shields are finished with a classy, laser etched, stainless steel IE logo badge.

EASY INSTALLATION

Installation is a quick and easy install with basic tools. The process should take around an hour for most enthusiasts. CLICK HERE to view and download the IE B9 Cold Air Intake Install Guide.

INSTALL OVERVIEW VIDEO

DYNO POWER RESULTS

The following power result data was collected on our in-house Dynapack hub dyno. Dyno chart is as tested at 4500 feet altitude with SAE corrected numbers. Before and after results are direct back-to-back comparisons on a full bolt-on stage 2 B9 A4 2.0T engine. The only change made to the vehicle between testing is the swap from a stock intake with a new clean air filter to the IE Cold Air Intake Kit. Dyno power results are approximate and may vary from car to car.

HORSEPOWER & TORQUE DYNO CHART

HORSEPOWER & TORQUE POWER GAINS OVER STOCK

VEHICLE FITMENT

• Audi - A4 2015+ (B9) 2.0T
• Audi - A5 2015+ (B9) 2.0T
• Audi - A4 Allroad 2015+ (B9) 2.0T

This intake does not fit cars that have a MAF housing/sensor.

Compatible with all Mk1 Q5 Models (8R)

P3 V3 Gauge Features

• Plug and Play Install - plugs directly into your OBD2 port (want to keep your OBD2 port open? hard-wire harness kit also available)
• OEM Integration - installs in your vent for a sleek install while retaining air flow
• Versatility - read boost from multiple OEM sensors through OBD2 port or using optional P3 analog boost sensor
• Code Reading/Clearing - read and clear diagnostic trouble codes (DTCs) on the fly

P3 V3 Gauge Readouts (all readouts can be individually configured to read in either Imperial or Metric units)

• Boost (through OBD2 port using OEM sensors or with P3 analog boost sensor)
• Coolant temperature
• Air/Fuel ratio (can be read in AFR or Lambda)
• Vehicle speed (can be calibrated in 1% increments from -9% to +20%)
• Intake air temperature (Charge Air Cooler Temp) "CAC-AIr" on 3.0T models
• Throttle angle
• Ignition timing
• Engine RPM
• Exhaust gas temperature
• Battery voltage
• Programmable shift light
• Analog input 1 (brown wire) can allow gauge to read any 0-5 volt linear output sensor
• Analog input 2 (blue wire) can allow gauge to read any 0-5 volt linear output sensor
• Acceleration timers (0-60mph/0-100mph/60-130mph)
• Braking timers (60-0mph/100-0mph)

OEM Vent Option

• We install the display in an OEM vent to make your install even easier

Optional Add-Ons

• P3 Analog Boost sensor - plugs directly into gauge harness, no wiring required)
• Boost tubing kit - Approx. 5' of 5/32" O.D. flexible plastic boost tubing with vacuum "T" and 3 sections of 5/32" I.D. vaccum hose. Includes 3 zip ties
• P3 ESVA (Ethanol Sensor Voltage Adaptor) allows your gauge to read ethanol content and fuel temperature directly from the common Continental/GM flex fuel sensor. *Ethanol sensor NOT included
• Trim Removal Kit - this tool kit will help you remove your vent and interior trim while minimizing the chance of scratching or damaging your trim
• OBD2 Splitter - attach multiple devices to your OBD2 port. *some devices will not function while another device is attached to the OBD2 port

You asked, we answered.

The P3 V3 Gauge adds even more user control to what the OBD2 Multi-Gauge already offered. Read DTCs on command, remove pids that you don't care to see, configure units settings of individual measurements, calibrate your vehicle speed, read AFR in Lambda.

There when you need it, hidden when you don't.

No more bulky pillar or column pods... No more squinting to read tiny pixelated screens...  While retaining the OEM plus design that blends into your interior, the P3 V3 packs a punch with it's bold, bright display that allows you to pick up info at a glance.

Hot or Cold? No problem!

Even though the P3 V3 installs in your air vent, we keep in mind that you need that heat and A/C while designing each gauge.

Electronics in a harsh climate? We've got that covered too.

We've torture-tested our gauges to the extreme. From frozen solid at -94 F to physically melting at hundreds of degrees, our gauges function far beyond the limits of the in-car environment.

Need more details? 

Check out the V3 install page for configuration and installation info.

P3 V3 Gauge Features

• Plug and Play Install - plugs directly into your OBD2 port (want to keep your OBD2 port open? (hard-wire harness kit also available)
• OEM Integration - installs in your vent for a sleek install while retaining air flow
• Versatility - read boost from multiple OEM sensors through OBD2 port or using optional P3 analog boost sensor
• Code Reading/Clearing - read and clear diagnostic trouble codes (DTCs) on the fly

P3 V3 Gauge Readouts (all readouts can be individually configured to read in either Imperial or Metric units)

• Boost (through OBD2 port using OEM sensors or with P3 analog boost sensor)
• Coolant temperature
• Air/Fuel ratio (can be read in AFR or Lambda)
• Vehicle speed (can be calibrated in 1% increments from -9% to +20%)
• Intake air temperature
• Throttle angle
• Ignition timing
• Engine RPM
• Exhaust gas temperature
• Battery voltage
• Programmable shift light
• Analog input 1 (brown wire) can allow gauge to read any 0-5 volt linear output sensor
• Analog input 2 (blue wire) can allow gauge to read any 0-5 volt linear output sensor
• Acceleration timers (0-60mph/0-100mph/60-130mph)
• Braking timers (60-0mph/100-0mph)

OEM Vent Option

• We install the display in an OEM vent to make your install even easier

Optional Add-Ons

• P3 Analog Boost sensor - plugs directly into gauge harness, no wiring required)
• Boost tubing kit - Approx. 5' of 5/32" O.D. flexible plastic boost tubing with vacuum "T" and 3 sections of 5/32" I.D. vaccum hose. Includes 3 zip ties
• P3 ESVA (Ethanol Sensor Voltage Adaptor) allows your gauge to read ethanol content and fuel temperature directly from the common Continental/GM flex fuel sensor. *Ethanol sensor NOT included
• Trim Removal Kit - this tool kit will help you remove your vent and interior trim while minimizing the chance of scratching or damaging your trim
• OBD2 Splitter - attach multiple devices to your OBD2 port. *some devices will not function while another device is attached to the OBD2 port

You asked, we answered.

The P3 V3 Gauge adds even more user control to what the OBD2 Multi-Gauge already offered. Read DTCs on command, remove pids that you don't care to see, configure units settings of individual measurements, calibrate your vehicle speed, read AFR in Lambda.

There when you need it, hidden when you don't.

No more bulky pillar or column pods... No more squinting to read tiny pixelated screens...  While retaining the OEM plus design that blends into your interior, the P3 V3 packs a punch with it's bold, bright display that allows you to pick up info at a glance.

Hot or Cold? No problem!

Even though the P3 V3 installs in your air vent, we keep in mind that you need that heat and A/C while designing each gauge.

Electronics in a harsh climate? We've got that covered too.

We've torture-tested our gauges to the extreme. From frozen solid at -94 F to physically melting at hundreds of degrees, our gauges function far beyond the limits of the in-car environment.

P3 V3 Gauge Features

• Plug and Play Install - plugs directly into your OBD2 port (want to keep your OBD2 port open? hard-wire harness kit also available)
• OEM Integration - installs in your vent for a sleek install while retaining air flow
• Versatility - read boost from multiple OEM sensors through OBD2 port or using optional P3 analog boost sensor
• Code Reading/Clearing - read and clear diagnostic trouble codes (DTCs) on the fly

P3 V3 Gauge Readouts (all readouts can be individually configured to read in either Imperial or Metric units)

• Boost (through OBD2 port using OEM sensors or with P3 analog boost sensor)
• Coolant temperature
• Air/Fuel ratio (can be read in AFR or Lambda)
• Vehicle speed (can be calibrated in 1% increments from -9% to +20%)
• Intake air temperature
• Throttle angle
• Ignition timing
• Engine RPM
• Exhaust gas temperature
• Battery voltage
• Programmable shift light
• Analog input 1 (brown wire) can allow gauge to read any 0-5 volt linear output sensor
• Analog input 2 (blue wire) can allow gauge to read any 0-5 volt linear output sensor
• Acceleration timers (0-60mph/0-100mph/60-130mph)
• Braking timers (60-0mph/100-0mph)

OEM Vent Option

• We install the display in an OEM vent to make your install even easier

Optional Add-Ons

• P3 Analog Boost sensor - plugs directly into gauge harness, no wiring required)
• Boost tubing kit - Approx. 5' of 5/32" O.D. flexible plastic boost tubing with vacuum "T" and 3 sections of 5/32" I.D. vaccum hose. Includes 3 zip ties
• P3 ESVA (Ethanol Sensor Voltage Adaptor) allows your gauge to read ethanol content and fuel temperature directly from the common Continental/GM flex fuel sensor. *Ethanol sensor NOT included
• Trim Removal Kit - this tool kit will help you remove your vent and interior trim while minimizing the chance of scratching or damaging your trim
• OBD2 Splitter - attach multiple devices to your OBD2 port. *some devices will not function while another device is attached to the OBD2 port

You asked, we answered.

The P3 V3 Gauge adds even more user control to what the OBD2 Multi-Gauge already offered. Read DTCs on command, remove pids that you don't care to see, configure units settings of individual measurements, calibrate your vehicle speed, read AFR in Lambda.

There when you need it, hidden when you don't.

No more bulky pillar or column pods... No more squinting to read tiny pixelated screens...  While retaining the OEM plus design that blends into your interior, the P3 V3 packs a punch with it's bold, bright display that allows you to pick up info at a glance.

Hot or Cold? No problem!

Even though the P3 V3 installs in your air vent, we keep in mind that you need that heat and A/C while designing each gauge.

Electronics in a harsh climate? We've got that covered too.

We've torture-tested our gauges to the extreme. From frozen solid at -94 F to physically melting at hundreds of degrees, our gauges function far beyond the limits of the in-car environment.

P3 Cars V3 OBD Vent Gauge to suit VW MK8 Golf R. P3 Digital gauges provide the highest level of OEM integration and colour matching to suit your vehicle.

P3 V3 Gauge Features

• Plug and Play Install - plugs directly into your OBD2 port (want to keep your OBD2 port open? 
  
• OEM Integration - installs the dash and cluster trim for a sleek install
• Versatility - read boost from multiple OEM sensors through OBD2 port or using optional P3 analog boost sensor
• Code Reading/Clearing - read and clear diagnostic trouble codes (DTCs) on the fly

P3 V3 Gauge Readouts (all readouts can be individually configured to read in either Imperial or Metric units)

• Boost (through OBD2 port using OEM sensors or with P3 analog boost sensor)
• Coolant temperature
• Engine oil temperature (GTI and Golf R)
• Air/Fuel ratio (can be read in AFR or Lambda)
• Vehicle speed (can be calibrated in 1% increments from -9% to +20%)
• Intake air temperature
• Throttle angle
• Ignition timing
• Engine RPM
• Exhaust gas temperature
• Battery voltage
• Programmable shift light
• Analog input 1 (brown wire) can allow gauge to read any 0-5 volt linear output sensor
• Analog input 2 (blue wire) can allow gauge to read any 0-5 volt linear output sensor
• Acceleration timers (0-60mph/0-100mph/60-130mph)
• Braking timers (60-0mph/100-0mph)

Optional Add-Ons

• P3 Analog Boost sensor - plugs directly into gauge harness, no wiring required)
• Boost tubing kit - Approx. 5' of 5/32" O.D. flexible plastic boost tubing with vacuum "T" and 3 sections of 5/32" I.D. vaccum hose. Includes 3 zip ties
• P3 ESVA (Ethanol Sensor Voltage Adaptor) allows your gauge to read ethanol content and fuel temperature directly from the common Continental/GM flex fuel sensor. *Ethanol sensor NOT included
• Trim Removal Kit - this tool kit will help you remove your vent and interior trim while minimizing the chance of scratching or damaging your trim
• OBD2 Splitter - attach multiple devices to your OBD2 port. *some devices will not function while another device is attached to the OBD2 port

You asked, we answered.

The P3 V3 Gauge adds even more user control to what the OBD2 Multi-Gauge already offered. Read DTCs on command, remove pids that you don't care to see, configure units settings of individual measurements, calibrate your vehicle speed, read AFR in Lambda.

There when you need it, hidden when you don't.

No more bulky pillar or column pods... No more squinting to read tiny pixelated screens...  While retaining the OEM plus design that blends into your interior, the P3 V3 packs a punch with it's bold, bright display that allows you to pick up info at a glance.

Electronics in a harsh climate? We've got that covered too.

We've torture-tested our gauges to the extreme. From frozen solid at -94 F to physically melting at hundreds of degrees, our gauges function far beyond the limits of the in-car environment.

LEADING INTAKE FEATURES

• Increased airflow - Get the most out of your upgrades
• High-flow velocity stack - True performance design
• Sealed heatshield - Separates cold air from engine bay heat
• Perfect fitment - No modifications required to bolt-on
• Amazing sound - Releases awesome turbo and engine noise
• Looks great - Black powder coat, tight clearances, clean angles 

AUDI B8 A4 & A5 COLD AIR INTAKE

You're not just building a run of the mill bolt-on car with cheap imported parts. No, your Audi B8 A4 or A5 project deserves true performance designed mods and the best cold air intake available. This is not your average filter on a stick, IE engineers used specialized computer flow analysis software coupled with 3D scans of the engine bay to maximize performance. The result is a unique intake shape that optimizes flow and reduces air restrictions for an unmatched bump in power. Factory-like mounting solutions are used for a perfect fit and long life. Your new intake will fit like it was there stock, but perform and sound like a true motorsport intake design.

EASY INSTALLATION

Installation is quick and easy to install with basic tools. The process should take under an hour for most enthusiasts. CLICK HERE to view and download the IE B8/B8.5 A4/A5 Cold Air Intake Install Guide.

VEHICLE FITMENT

• Audi - A4 2009-2015 (B8-B8.5) 2.0T
• Audi - A4 Allroad 2009-2015 (B8-B8.5) 2.0T
• Audi - A5 2009-2015 (B8-B8.5) 2.0T