Search results for 'audi a3 s3 8pr'

H&R Sport Sway Bars are crafted from a special 50CRV4 steel alloy, the highest tensile strength available.

The quality of the material and design guarantees smooth transitional sway bar function, decreasing feedback response time and increasing stiffness over stock.

H&R Sport Sway Bars improve lateral stability and cornering grip, while reducing body roll. H&R Sport Sway Bars are designed for drivers who desire improved handling without lowering or affecting ride quality. H&R Sport Sway Bars increase stiffness and reduce body roll while maintaining comfort and increasing cornering control, lateral stability, and grip. 

A unique feature of H&R Sport Sway Bars are the smooth, machined-like forged ends that, for specific vehicles, allow for adjustability in stiffness.

Being 100% German made means a commitment to doing it right and giving you the best quality product.

Features:
- Reduces body roll
- Highest tensile strength available
- Works with DCC (adaptive suspension)

- Special urethane/Teflon composite bushes that are maintenance free

Swaybar Size:
- Front 24mm

- Rear 26mm

Adjustable:
- Front x2
- Rear x2

Compatibility:

• Audi A3 8P 2003-2012 4WD
• Audi S3 8P 2003-2012 4WD
• Skoda SUPERB 3T SEDAN 4WD
• Skoda OCTAVIA 1Z SEDAN + WAGON 4WD
• VW GOLF MK5 2003-2008 4WD
• VW GOLF MK6 2008-2012 4WD
• VW PASSAT B6/B7 2005-2014 4WD
• VW Tiguan 5N 2007-2015 4WD

Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

CTS Turbo is proud to release our B-Cool Billet Oil Filter Housing.  The OE plastic filter housing is quite fragile and is know to become brittle and crack over time.  Each CTS Turbo B-Cool Billet Oil Filter Housing is constructed in house from T6061 Aluminum.  Not only does the B-Cool filter look good, but it works great.  We have engineered cooling fins into our design to act as a heatsink, which dissipates heat from the engine oil.

Installation is very straight forward and only required basic hand tools:

Drain oil from filter housing, use a 36mm socket to remove the factory oil filter housing, install new filter, install new filter housing o-ring to CTS housing, reinstall on the car and tighted to 18 ft/lbs, refill engine oil.

Product Details:

•   Made in Canada from billet T6061 Aluminum
•   Hard anodized black for stealth and longevity (machined finish shown)
•   Uses OEM O-ring
•   Installation of CTS-HW-0242 requires removal of center cage from OE housing cap, which snaps into the CTS billet housing
•   OE-style threads are precision made to fit just like factory part. Other manufacturers do NOT make this thread.
•   Compatible with OEM Filter

The CTS B-Cool Billet fits Audi, VW, Seat, Skoda models with EA113 2.0T FSI engines, 2.5L 5-cylinder engines and 2.5T 5-cylinder turbo engines.

This part replaces the OE part# 06D 115 408B and 07K 115 408.

Fitment:

• MK6 Golf R, MK5 GTI (FSI), 8P Audi A3 (FSI), MK2 Audi TT-S (FSI)
• MK5 and MK6 Golf, Jetta 2.5 5-cylinder
• 8P Audi RS3 (not for facelift model)
• MK2 Audi TT-RS (not for facelift models)

This recirculating catch can kit has been designed for use with the IE billet valve cover (IE part number: IEBAVC5) as a simple install solution for your billet valve cover and catch can. 
IE billet valve cover sold separately. 

Product Features