SHIFT FASTER, DRIVE FASTER The IE DSG Tune for your VW MK6 GTI, Jetta, GLI, or Audi 8J TTS 2.0T delivers increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control, and additional transmission performance features when paired with a matching ECU tune. Acceleration times will greatly improve turning your tuned 2.0T TSI into a fully rounded performance monster. LEADING FEATURES Lightning fast gear shifts Higher shift points of 6800 RPM Kick down in manual mode eliminated Lag time reduced when starting off in first gear Multiple launch RPMs: 3200, 3400, 3600, 3800, 4000 Drive shift mapping entirely reworked with an enthusiast in mind Flashed directly through OBD-II Port (No TCU removal required) Works flawlessly with an IE ECU tune Increased clutch pressure on tap for higher torque without slip Temperature protection remains for safety Gear hunting reduced Gearbox “Torque Limiters” removed WHAT DOES A DSG TRANSMISSION TUNE DO? The IE DSG Tune for the MK6 2.0T TSI has been carefully set up to make the car way more fun to drive. It completely reworks the shift point mapping in both drive and sport. The transmission will no longer lug the engine in drive mode. Clutch clamping forces are increased so the transmission can safely handle much more power. Shifts are much, much faster taking time directly off the 0-60 and ¼ mile times. ONE TUNE FOR ALL STAGES IE’s TCU/DSG tune is all-inclusive and does not offer expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset. A great deal of sportiness is added from the tune while maintaining factory smoothness and driveability. More aggressive launches and faster shifts are guaranteed to put a smile on your face. Also, expect acceleration and 0-60 times to improve from faster shifting. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes. USER ADJUSTABLE LAUNCH CONTROL The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! Available Launch Control RPMs: 3200 RPM 3400 RPM 3600 RPM 3800 RPM 4000 RPM IE DSG TUNE TECHNICAL FEATURES HIGHER SHIFT POINTS Utilize the whole powerband of your 2.0 TSI engine without the DSG interfering and shifting early. DRIVE MAPPING REWORKED The MK6 2.0 TSI DSG is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode. INCREASED CLUTCH PRESSURE Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive. FLASHED THROUGH OBD-II PORT There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes. TAKE-OFF LAG REDUCED The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop. MULTIPLE LAUNCH RPMS The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! KICK DOWN REMOVED IN TIPTRONIC/MANUAL MODE The kick down switch is disabled in manual shift mode, ensuring you stay in the gear you’ve selected, even during hard launches or over bumpy terrain FLAWLESS OPERATION WITH IE ECU TUNES The IE DSG Tune and ECU Tune were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 2.0 TSI engine and transmission. VEHICLE FITMENT VW - MK6 GTI 2010-2014 (MK6) 2.0T EA888 Gen1/2 TSI engines VW - MK6 Jetta 2011-2013.5 (MK6) 2.0T EA888 Gen1/2 TSI engines* VW - MK6 GLI 2011-2013.5 (MK6) 2.0T EA888 Gen 1/2 TSI engines* AUDI - TTS 2008-2015 (8J) 2.0T TFSI EA113 engines *This DSG calibration is for 2.0T TSI EA888 Gen 1 & 2 engines only. Many Jetta and GLI models are equipped with a new engine variation (EA888 Gen 3) after 2013.5 and later. This tune does NOT support Gen 3 model engine TCUs. Please verify if your engine is an EA888 Gen 1/2 2.0T TSI or EA888 Gen 3 2.0T TSI tune before ordering. IE DSG tunes are available only for vehicles equipped with 6 speed DSG (DQ250) transmissions. Does not function with manual 6-speed transmission cars.

MK7 & MK7.5 MQB GOLF R / S3 TUNE FEATURES Stage 1 & Stage 2 files available to match any level of bolt-on parts Horsepower & torque gains maximized on stock engine & turbo Switch between 91, 93, & 104 octanes at no extra cost Stock boost control optimized for a smooth driving experience Rev limiter increased to 7100 RPM in manual mode or with DSG flash Quick and easy to tune your car at home Launch control boost pressure increased for faster starts (DSG) Increased rev limiters (transmission stock shift points remain) Road speed limiters removed All engine safety protocols remain for reliability and long engine life POWERlink allows file and octane switching in less than 2 minutes Engineered for all climates and elevations Simple data logging for diagnosis purposes Flash back to stock at any time HOW TO IE TUNE YOUR 2.0T (IS38) IE ECU Stages for your VW Golf R or Audi S3 2.0T IS38 Turbo (MQB) engine is available for stock engines or with modified hardware for Stage 2. Read below to determine the best stage for your build! In order to flash your vehicle, you will need an IE POWERlink Direct-port Flash Tool (sold separately) and a Windows 7+ powered laptop. Already own an IE POWERlink cable? Contact us to purchase upgrade credits, there is no fee to upgrade tunes and you only pay the difference in tune cost. Follow the link provided with your IE POWERlink Flash Tool to download our Flash Wizard software and follow the on-screen directions to tune your MK7 R or 8V S3 in a matter of minutes! WHAT DOES THE AUDI 2.0T ECU TUNE DO? Adding an IE Performance ECU Tune to your Golf R packs a serious punch both in performance gains and in additional features resulting in extremely competitive power that will give you the edge on the street or track. IE’s in-house calibration engineers have taken several steps to ensure you a smooth and safe operation by maintaining factory safety limits, or “fail safes”, resulting in reliability. As a final step, the software has been calibrated in test environments that ensure smooth operation in all types of climates and elevations. AVAILABLE MK7/8V IS38 TUNES Stage 1 is precisely calibrated to make the most of your stock hardware. Power gains are delivered smoothly across the entire powerband and many performance features have been added. Enthusiasts will have the choice between 91 & 93 fuel octanes and the ability to flash back to stock within minutes. As another added benefit, your IE Stage 1 Tune has been designed to adapt to minor bolt-on modifications, such as an intercooler or intake. Low torque and high torque files are available. Stage 1 Low Torque recommended hardware -IE Cold Air Intake (recommended) Stage 1 High Torque required & recommended hardware -IE DSG Transmission Tune (required) -IE Cold Air Intake (recommended) Ready to release every last ounce of power from your stock turbo 2.0T engine? The Stage 2 ECU tune takes full advantage of performance bolt-ons including downpipe, intake, and intercooler. You can install this setup in a single weekend and transform your Golf R or S3 into a true AWD monster with 432HP and 467TQ! Easily switch between free octane tunes whenever you want to add more power with your choice of 91, 93, or 104 octane files. Load Stage 2 and get ready to experience the true power monster that has been hiding under the hood of your MK7 Golf R or 8V S3. Stage 2 required & recommended hardware -IE Performance Downpipe (required) -IE DSG Transmission Tune (required) -IE Intercooler (highly recommended) -IE Cold Air Intake (highly recommended) AVAILABLE OCTANES All available tune stages include various octanes at no extra cost. Using the IE POWERlink cable you can switch between octanes as needed. You can load high octane files for race day and run regular pump octane on your daily commute and save at the pump. STAGE 1 OCTANES: Pump 95 Pump 98 STAGE 2 OCTANES: Pump 95 Pump 98 Race Fuel 108 EASY INSTALLATION – TUNE FROM HOME IE’s own in-house developed POWERlink cable gives you the control to unlock your engine’s true potential from your own garage or driveway. Enjoy the freedom to quickly reflash your car’s engine control unit (ECU) or transmission control unit (TCU) with IE’s line of performance tunes. The cable simply plugs into your vehicle’s OBD-2 port delivering instant access to choose different IE Tune stages to match installed hardware, take advantage of different fuel octanes, flash back to stock, perform engine diagnostics, read/clear codes and gather high-quality operating data via logging.

AUDI B9 2.0T TUNE FEATURES

HOW TO TUNE YOUR B9 A4 or A5

IE ECU Stages for your Audi B9 engine are available for stock (Stage 1) or with modified hardware for Stage 2. Read below to determine the best stage for your build!

In order to flash your vehicle, you will need an IE POWERlink Direct-port Flash Tool (sold separately) and a Windows 7+ powered laptop. Already own an IE POWERlink cable? Contact us to purchase upgrade credits, there is no fee to upgrade tunes and you only pay the difference in tune cost.

Follow the link provided with your IE POWERlink Flash Tool to download our Flash Wizard software and follow the on-screen directions to tune your Audi in a matter of minutes!

WHAT DOES THE IE AUDI B9 ECU TUNE DO?

Your ECU (Engine Control Module) is a computer loaded with maps to control the operating conditions of your Audi 2.0T engine. The factory calibration is designed to function with stock installed hardware, meet new car regulated standards, and de-powered to not compete with higher performance models. IE's motorsport recalibration brings your engine to life by unleashing its full performance potential on stock hardware or to match your installed hardware upgrades while maintaining reliability and factory-like comfort. This is how your turbocharged Audi should have felt from the factory!

 

VEHICLE FITMENT

• Audi - B9 A4 Quattro 2016+ with 2.0T engine*
• Audi - B9 A5 Quattro 2016+ with 2.0T engine*
• Audi - B9 A4 Quattro Allroad 2017+ with 2.0T engine*

*For all wheel drive (Quattro) vehicles only, does not support front wheel drive engines at this time.

A TRUE PERFORMANCE MANIFOLD

Gain power and torque across the entire rpm range with no loss in turbo spool time with a true motorsport designed intake manifold for your VW or Audi 2.0T FSI EA113 & TSI EA888 Gen1/2 engine. The IE 2.0T Intake Manifold has been carefully designed to provide an effective power increase across the entire rpm range with no loss in low-end power or spool time with the ability to be used on any turbo setup, including the stock turbo. This manifold completely replaces the factory failure prone and restrictive plastic manifold with a high-performance USA cast aluminum part that will look amazing, last the life of the vehicle, and add more power! 

LEADING INTAKE MANIFOLD FEATURES

• Power and torque gains throughout the entire rpm range
• Fast onset boost, no loss in spool time
• O ring seals, no liquid gasket or RTV required
• No wiring modifications or extensions required
• Thick wall cast construction for durability
• Black anodized velocity stack cover
• Black powder-coat finish for a clean look and easy maintenance
• 100% engineered, tested, designed, cast, and machined in the USA
• Bolt-on install kits available for most vehicles

VEHICLE SPECIFIC INSTALL KITS

Designed specifically for each individual application, IE Intake Manifold Install Kits are complete with all hardware necessary to install your new IE 2.0T cast intake manifold. These kits including all needed brackets to fasten OEM lines and components, as well as couplers to plumb the valve cover breather, vacuum connections, and throttle body. Verify the correct install kit for your vehicle below before ordering.

2.0T FSI (EA113) TRANSVERSE KIT FITMENT

• VW - MK6 Golf R (2012-2013)
• VW - MK5 GTI 2.0T FSI (2006-2008)
• VW - MK5 Jetta & GLI 2.0T FSI (2005-2008)
• AUDI - 8J/MK2 TTS (2009-2015)
• AUDI - 8J/MK2 TT 2.0T FSI (2008-2010)
• AUDI - 8P/MK2 A3 2.0T FSI (2006-2008)

2.0T FSI (EA113) LONGITUDINAL KIT FITMENT

• AUDI - B7 A4 2.0T FSI (2005-2008)

2.0T TSI (EA888 GEN 1 & GEN 2) TRANSVERSE KIT FITMENT

• VW - MK6 GTI 2.0T TSI (2010-2014)
• VW - MK5 GTI 2.0T TSI (2008-2010)
• VW - MK6 Jetta & GLI 2.0T TSI (2011-2013)
• VW - MK5 Jetta & GLI 2.0T TSI (2008-2011)
• AUDI - 8J/MK2 TT 2.0T FSI (2010-2015)
• AUDI - 8P/MK2 A3 2.0T FSI (2008-2013)

2.0T TSI (EA888 GEN 1 & GEN 2) LONGITUDINAL KIT FITMENT

• AUDI - B8 A4 2.0T TSI (2009-2013)
• AUDI - B8 A5 2.0T TSI (2009-2013)

REQUIRES MANIFOLD ECU SOFTWARE

The IE 2.0T Intake Manifold is a true performance designed intake manifold and requires specific tuning to the ECU software to take advantage of the larger plenum volume, runner size, resonance tuning, and velocity stacks to gain the power increase. Simply bolting the manifold on your existing ECU tune is unlikely to gain the optimum power available. Additionally, installing the IE manifold will remove the factory plastic manifold's runner flaps. Removing the runner flaps will cause a check engine light (CEL) and possible rough cold starts, especially in cold weather. Your manifold tune must turn off the runner flap codes to remove the CEL and re-tune the warm-up maps to accommodate for the cold starts. Please ensure your ECU tuner can provide you with manifold software before purchasing.

Vehicle specific manifold tunes are available from IE for certain cars with more being added in the future. See below for a list of available software tunes.

• VW MK5 GTI Stage 2 IM Software
• VW MK6 GTI Stage 1 IM Software
• VW MK6 GTI Stage 1 IM Software
• VW MK6 Golf R Stage 2 Pro IM Software

USA CAST ALUMINUM

IE manifolds are cast from a special self-aging, self-hardening alloy with especially strict requirements for chemical composition. Top of the line Japanese machining centers machine all major surfaces of the parts in one setup, ensuring a perfect fit, finish, and maximum value. The aluminum manifold makes a great replacement for the stock plastic unit, which is a common failure point.

FLOW TUNED RUNNER DESIGN & VELOCITY STACKS

Dramatic power and torque increases come from making small changes to the runner and velocity stack design. Our engineers have precisely tuned runner length, diameters, and resonance tuning. The IE manifold is the only manifold on the market featuring flow tested velocity stacks that have been optimally tuned for large power increases throughout the entire RPM band. The end result is the best performing intake manifold optimized specifically for 2.0T engines.

INCREASED PLENUM VOLUME

The plenum on this manifold has been generously sized and shaped to distribute airflow as evenly as possible to all 4 cylinders. The 2.4L internal volume is a massive improvement over the factory piece and ensures a steady supply of air for the engine.

POWER INCREASE

We have carefully engineered and tested this intake manifold in-house to get the best results possible in any condition. Using the latest in Computational Fluid Dynamics (CFD) software, our engineers have optimized the manifold's airflow and power range for virtually any turbocharger. Even on smaller turbos such as VW/Audi K04 turbos, there are significant power and torque increases throughout the entire rpm range, with no loss in low-end power or spool time. What that means for you is an incredible increase in the driving experience with a bolt-on performance product, with truly no downsides. Larger power gains are to be seen on big turbo setups as well, with a manifold that is tuned for the natural powerband of the 2.0T engines from 3000-7500rpm.

QUICK SPOOL

With further careful tuning of the runner diameter and length, the IE manifold provides an optimal balance of power gains throughout the entire powerband with no loss in spool time or low-end power. Even on both smaller and larger turbo setups, the manifold will typically result in no added turbo lag.

DIRECT FIT

The Integrated Engineering 2.0T performance intake manifold has been carefully designed to fit many 2.0T FSI/TSI (EA113 & EA888 gen1/gen2) engines while retaining all of your factory components. Through extensive research and development, this intake manifold fits with no modifications to the engine bay, charge piping, vacuum system, emissions systems, fuel system, or coolant system. To make the intake manifold install as painlessly as possible, individual install kits are available separately. Check the Fitment tab to find the install kit for your vehicle.

SURFACE FINISH

To complement the impressive performance of the manifold design, IE engineers have taken special care to make a visually appealing piece that not only compliments but enhances the look of any engine bay. The beautiful USA cast aluminum surface is powder coated with a satin black finish then all surfaces and ports are machined for an impeccable contrast. The easy to clean powder coat will ensure the manifold stays looking nice for a lifetime. The top of the manifold features an in-house CNC machined black anodized aluminum velocity port cover that looks amazing in any engine bay.

PRECISION ENGINEERING

Unlike other manifolds on the market that are simply welded or cast with larger plenums and made to fit on the car, IE's performance intake manifolds receive special treatment from start to finish. Our engineering department looks at each specific application and designs an intake manifold with a properly sized runner and plenum. Then we begin a series of prototyping and testing countless revisions to the design to ensure optimum performance. Our engineers use Computational Fluid Dynamics (CFD) software to optimize the runner and velocity stack (bellmouth) system for proper resonance tuning and airflow. Unlike competitor manifolds, we use this process on each manifold to design the application-specific runner system to maximize airflow delivery to the cylinders.

Once the manifold has been designed and flow has been optimized, the 3D models head over to our 3D printing studio to manufacture the initial prototype. The 3D printed manifold is fastened onto our in-house engine dynamometer and in-house chassis dynamometer for testing. To validate the plenum, runner, and bellmouth design, we test each revision in a controlled environment. Once all the testing data has been collected, it is analyzed and used to determine if changes are necessary before going into production.

WATER/METHANOL READY

Each runner is ready for individual water/methanol injection nozzles. The cast and pre-drilled and threaded 1/8" NPT ports located on each runner will make installing your water/meth setup easy. For builds not using water/methanol injection, you can simply block off the ports using the provided black plugs. This requires a 1/8" thread "elongated" nozzle to use with our manifold. These nozzles are manufactured by Aquamist and available through aquamist-direct.com for purchase.

VEHICLE FITMENT BY ENGINE

Requires vehicle specific install kit for complete installation.

VW & Audi - 2.0T FSI EA113 Engines

• Audi - A4 2005-2008 (B7) 2.0T EA113 TFSI engines
• Audi - A6 2005-2011 (C6) 2.0T EA113 TFSI engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T EA113 TFSI engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T EA113 TFSI engines
• Audi - TTS 2008-2015 (MK2-8J) 2.0T EA113 TFSI engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T EA113 TFSI engines
• VW - Golf R 2012-2013) (MK6) 2.0T EA113 FSI/TSI engines
• VW - GTI 2006-2009 (MK5) 2.0T EA113 FSI engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T EA113 FSI engines
• VW - Passat 2006-2010 (B6) 2.0T EA113 FSI engines

VW & Audi - 2.0T TSI EA888 Gen 1/2 Engines

• Audi - A4 2009-2015 (B8 - B8.5) 2.0T TSI EA888 Gen 1/2 engines*
• Audi - A4 Allroad 2009-2015 (B8 - B8.5) 2.0T TSI EA888 Gen 1/2 engines*
• Audi - A5 2008-2015 (B8 - B8.5) 2.0T TSI EA888 Gen 1/2 engines*
• Audi - A6 2012-2015 (C7 - C7.5) 2.0T TSI EA888 Gen 1/2 engines*
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T TSI EA888 Gen 1/2 engines*
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T TSI EA888 Gen 1/2 engines*
• VW - GTI 2006-2009 (MK5) 2.0T TSI EA888 Gen 1/2 engines*
• VW - GTI 2010-2014 (MK6) 2.0T TSI EA888 Gen 1/2 engines*
• VW - Jetta & Jetta GLI 2010-2014 (MK6) 2.0T TSI EA888 Gen 1/2 engines*
• VW - SportWagen 2011-2014 (MK6) 2.0T TSI EA888 Gen 1/2 engines*
• VW - CC 2009-2015 (3C8) 2.0T TSI EA888 Gen 1 & 2 engines*
• VW - Passat 2006-2010 (B6) 2.0T TSI EA888 Gen 1 & 2 engines*

*Does not fit B8/B8.5 A4 & A5 2.0T TSI engines with 5th injector factory aluminum intake manifolds.

*Fits VW & Audi 2.0T FSI EA113 and TSI EA888 Gen 1/2 engines only, does not fit MK7/MQB EA888 Gen 3 engines.

EVAP Crossover Tube Relocation Kit for 2.0T FSI with IE Valve Cover

This recirculating catch can kit has been designed for use with the IE billet valve cover (IE part number: IEBAVC5) as a simple install solution for your billet valve cover and catch can. 
IE billet valve cover sold separately. 

 

Product Features

 

Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!

PRODUCT DETAILS

IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.

MACHINED DESIGN

Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.

FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY

This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.

PRODUCT FEATURES

 

• Replaces factory plastic valve cover
• Uses factory valve cover gasket
• In-house CNC machined from aluminum
• Includes o ring sealed matching billet oil cap
• -10AN breather outlet for catch can setups

ADDITIONAL PARTS REQUIRED

 

EVAP CROSSOVER TUBE RELOCATION KIT

The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11

CATCH CAN KIT FOR BILLET VALVE COVER

The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3

 

VEHICLE FITMENT

• Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
• Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
• Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
• Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
• VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
• VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
• VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
• VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*

*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.