The CTS Turbo Golf R / FSI intake heat shield is designed to mount simply to the factory mounting points. With a brushed aluminium finish this heat shield not only reduces your intake temps, but dresses up the engine bay like no other
Product Details
The ECS Billet Aluminum Manifold Port Boost Tap Kit conveniently adds three boost / vacuum ports to your Gen3 engine for any of your specific needs. Located on the left side of the intake manifold within the unused side intake port, this location provides a strong pneumatic signal and allows for an installation.
Through multiple design revisions and product testing, our team of engineers found that other methods of acquiring a manifold signal, such as spacing the MAP / IAT sensor on top of the intake manifold, lead to skewed data being transmitted to the ECU. We found that intake air temperatures were reading lower (15-20° F at WOT), ignition timing was off (as much as -5°) and air /fuel ratio was richer (+1.0 point by 5,000 RPM). This directly translated into engine power dropping by as much as 6 WHP on an untuned vehicle!
You can be certain that all critical data is not affected and your engine's ECU has all of its valuable information to properly adjust timing and fuel with our leading edge design! Engineered specifically for the Gen3 engine, we designed our Manifold Port Boost Tap with 3 ports, so you have multiple options to provide the strongest manifold signal to either your boost gauge, blow off valve, water meth switch or any other pneumatic device.
In house designed and built in the USA, our Boost Tap includes the following:
Black Anodized, Billet Machined 6061-T6 Aluminum Manifold Port Boost Tap
3 Vacuum Ports with 1/4" Hose Barb Fittings
3 Vacuum Set Screws
Medium Strength Thread Lock
OEM Securing Clip
Manifold Pierce Alignment Tools
In-house designed and made in America, you can expect nothing short of the best performance and longevity with this superior Manifold Port Boost Tap Kit from ECS Tuning!
IE cone filters are specifically designed for high-flow and perfect fitment to the integrated velocity stack found on most IE cold air intake kits. This is a dry filter that can be oiled, however, we do not recommend air filter oiling on turbocharged or forced induction vehicles. The filter can be cleaned and re-used many times. If you find it difficult to clean your filter or find it severy stained, it may be time to replace the filter element. This is a direct replacement filter ready to keep your car on the road and performing at its best. Includes new filter clamp.
The IE Audi B9 A4 & A5 2.0T Cold Air Intake is the perfect addition to any engine bay. Give your Audi added horsepower, torque, snappier throttle response, and an aggressive sound. Typical peak gains from our CAI are roughly 10-20 Horsepower and Torque.
POWER GAINS
The ram air design, velocity stack, and massive 55-inchfilter inlet help deliver the most HP possible from a cold intake system.
Expect peak gains of 10-20+HP/TQ on tuned engines.
INCLUDED IN THE B9 IE CAI KIT
IE Intake velocity stack & heatshield assembly
IE Silicone turbo inlet pipe assembly
IE 5” inlet performance air filter
IE Turbo heat shield
All necessary hardware (clamps, nuts, bolts, etc)
INCREASED AIR FLOW
This Intake delivers an impressive flow increase to feed your turbo. More cold air flow means more power; especially during the hot summer months. Ditch your stock restrictive airbox for the IE intake System.
DESIGN DETAILS
IE engineers set out to produce the highest performing cold air intake that looks great and fits like a factory installed part in your A4. The latest in computer design and 3D scanning technology were employed during the development process for a perfect fit and maximum performance. The final product resulted in the greatest performing and best-looking intake available.
HIGH-FLOW VELOCITY STACK
Delivering cold air to your engine is a must for making power. The velocity stack efficiently channels air as quickly as possible into the intake system. The velocity also functions as a solid mount for the air filter which means no intake pipes rattling on heat shields.
CUSTOM HEAT SHIELD
IE uses a three piece heat shield which performs and looks great. It effectively channels cold air from the front of the car to the massive performance filter. Furthermore, it eliminates the induction of hot air found in other locations of the engine bay. A second heat shield is mounted above the turbocharger to further protect against power robbing heat off the exhaust and turbo.
PERFECT FITMENT
This Intake fits B9 Audi A4 and A5 without any modification or installation hassles. The install process is simple and can be done quickly with basic tools. The fact that IE intake utilizes the factory airbox mounts ensures a perfect and hassle free fit. Additionally, the stock rubber mounts allow for engine movement which keeps intake components from getting damaged.
CLASSY AND CLEAN APPEARANCE
Wrinkle black powder coated velocity stack and heat shields result in a sleek and sporty appearance in any engine bay. As a final touch, all IE heat shields are finished with a classy, laser etched, stainless steel IE logo badge.
The following power result data was collected on our in-house Dynapack hub dyno. Dyno chart is as tested at 4500 feet altitude with SAE corrected numbers. Before and after results are direct back-to-back comparisons on a full bolt-on stage 2 B9 A4 2.0T engine. The only change made to the vehicle between testing is the swap from a stock intake with a new clean air filter to the IE Cold Air Intake Kit. Dyno power results are approximate and may vary from car to car.
HORSEPOWER & TORQUE DYNO CHART
HORSEPOWER & TORQUE POWER GAINS OVER STOCK
VEHICLE FITMENT
Audi - A4 2015+ (B9) 2.0T
Audi - A5 2015+ (B9) 2.0T
Audi - A4 Allroad 2015+ (B9) 2.0T
This intake does not fit cars that have a MAF housing/sensor.
At CTS Turbo we are proud to announce our new air intake system for the MK5 R32. The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our high quality silicones fit seamlessly with the OEM MAF flange allowing for smooth entry of cold air into the the engine providing peak power gains ranging from 9-15HP. All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.
This is a CTS Turbo universal 3″ low profile cone filter, it has a tapered design to fit in tight spots. These filters are used in our MK4 1.8T, 2.0T FSI, 2.oT TSI, B8 A4 intake kits. Also these filters can also be used in a custom big turbo application.
3.0″ Inlet x 8.0″ Long x 5.0″ Wide High quality molded silicon base and cap Stainless steel clamp
6-Inch Bell Mouth Cold Air Intake V1.1 Introduction
We are excited to introduce you to our first of many Hyundai I30n bolt-on upgrade parts. Hyundai has outdone themselves with the I30 n, and we are eager to push the limits of this amazing, extremely underrated car. Our aim for our Hyundai i30 n development program is to deliver high-performing parts and intelligent design to provide aftermarket capability with OEM quality. Our team are incredibly passionate about creative and innovative design while maintaining practicality, taking pride in our ability to achieve a flawless fit and finish, time after time. We have put a lot of time into planning our parts development program for the I30 n, with modular integration of future parts already designed into this 6-Inch Bell Mouth Cold Air Intake, The largest available for the Hyundai I30 n. We are in the final stages of finishing three new products for the I30 n, with many more in the planning and early development stages. Benefits of Fitting a Cold Air Intake Colder air, better noises, more power
IE Performance Cold Air Intake V2 Carbon Fiber Lid (No Intake)
The all-new Integrated Engineering 2.0T Gen 3 Cold Air Intake System for the VW/Audi MQB platform has been completely reimagined and redesigned from the ground up. Featuring a new 3.5" turbo inlet pipe and heat shield that spans the entire length of the radiator inlet to support massive power gains from even large turbo and hybrid setups. New modular design allows the intake to be ran as a cost-friendly open filter intake, or upgraded with a high-gloss carbon fiber assembly further reducing hot engine bay air and adding a high-quality style to your engine bay.
Included:
High-Gloss Carbon Fiber Intake Lid
PACKAGE CONTENTS:
High-gloss Carbon Fiber Lid ONLY (THIS LISTING DOES NOT INCLUDE THE INTAKE)
Get The Complete Carbon Fiber Intake Kit (See below):
This product page is only for the carbon fiber lid. This does not include an intake. We've bundled the intake and cover for your convinience. Combine Performance and style.
With the announcement of our all-new modular MQB intake comes the end of our previous open filter and carbon fiber models. The new intake is higher performing, improved fit, and more budget-friendly for the carbon variation.
At CTS Turbo we are proud to announce our new air intake system for the transverse 2.0T FSI EA113 VW/Audi range of vehicles.
The air scoop works in conjunction with our sealed airbox to seamlessly force cold air into our 2.75″ air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 9-15WHP. By using a factory MAF position, you can be sure that fuel trims will remain perfect.
All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.
This intake kit is designed to be compatible with our FSI EA113 BOSS kits; intake pipe features 2x 1/8″ bungs and 1x 1/2″ bung for easy installation of BOSS kits. Plugs are included.
Product Details:
Full 2.75″ Mandrel-bent aluminum piping with black powder coating
Compatible with CTS BOSS kits, with provisions for easy installation
Reusable 3″ air filter with inverted cone design
4 Ply silicon connectors with stainless steel clamps
Air box with rubberized trim
Bracketry to prevent rattling under engine torquing
Gains ranging from 9-15WHP on stock vehicle, even more if tuned!
At CTS Turbo we are proud to announce our new 3″ air intake system for the 1.8TSI and 2.0T Gen1 and Gen3 VW/Audi range of vehicles. This kit includes parts that make it compatible with both generations of TSI engines!
The air scoop works in conjunction with our sealed airbox to seamlessly force cold air into our 3″ air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our 3″ CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 9-15WHP. By using a factory MAF housing (when equipped), you can be sure that fuel trims will remain perfect.
All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.
This intake kit is designed to be compatible with our TSI Gen1 BOSS kits; intake pipe features 2x 1/8NPT bungs for easy installation of BOSS kits.
Product Details:
Full 3″ Mandrel-bent aluminum piping with black powder coating
Compatible with CTS BOSS kits, with provisions for easy installation
Reusable air filter with inverted cone design
4 Ply silicon connectors with stainless steel clamps
Airbox with rubberized trim
Bracketry to prevent rattling under engine torquing
Gains ranging from 9-15WHP on a stock vehicle, even more, if tuned!
