Description:
Get the latest in performance aesthetics with Leyo Motorsports light weight aluminium engine fluid caps. Made from the finest raw materials, these fluid caps will add that clean modified look to your engine bay without the messy installation. Designed in-house by our technical team, these caps are built to perfection to seamlessly integrate with your vehicle engine bay.
We offer four unique caps for the oil filler neck, the coolant reservoir, the brake fluid reservoir and finally the windshield washer tank. Changing these under the bonnet will add that unique personal touch and create an engine bay you’d be proud to show off with the confidence of performing better than the OEM parts. To make installation as simple as possible, we’ve included an Allen Set screw wrench for your new aluminium engine compartment oil caps.
Don’t wait, get the stylish appearance your car deserves from Leyo Motorsport today.
Specifications:
Available for all accessory cap looks like this.
BRAKE FLUID RESERVOIR CAP
Description:
Unleash the power of your R with the Leyo high flow decat downpipe. By forgoing the restrictive catalyst, the full potential of your R can now be released. This downpipe is made with high grade 304 stainless steel for long lasting durability. Leyo downpipe works with either Leyo Catback Exhaust System or factory catback exhaust.
Specifications:
3” 304 stainless steel downpipe.
Direct bolt on.
Description:
Want to enhance driving dynamics of your Golf R? Reduce body roll during cornering? Improve ride quality? Enhance visual appeal of your ride?The solution to all of these is our dynamic lowering springs for the VW MK7 / MK7.5Golf R.
Leyo Motorsport lowering springs lowers the car on an average of 20-25mm. With the now lower center of gravity, excessive body roll is reduced during cornering. The ugly gap between the tire and wheel arch has also been reduced giving your car a meaner stance than before.
As with every Leyo Motorsport product, these lowering springs has been tested in real world condition and on the race track before releasing it to the market ensuring that you receive the best product there is on the market.
Specifications:
Reduce body roll
Improve ride quality
Enhance driving dynamic
Lowers the car 20-25mm
Description:
Get the latest in performance aesthetics with Leyo Motorsports light weight aluminium engine fluid caps. Made from the finest raw materials, these fluid caps will add that clean modified look to your engine bay without the messy installation. Designed in-house by our technical team, these caps are built to perfection to seamlessly integrate with your vehicle engine bay.
We offer four unique caps for the oil filler neck, the coolant reservoir, the brake fluid reservoir and finally the windshield washer tank. Changing these under the bonnet will add that unique personal touch and create an engine bay you’d be proud to show off with the confidence of performing better than the OEM parts. To make installation as simple as possible, we’ve included an Allen Set screw wrench for your new aluminium engine compartment oil caps.
Don’t wait, get the stylish appearance your car deserves from Leyo Motorsport today.
Specifications:
Constructed from T6061 Billet Aluminium for strength.
Hard coated anodized finish.
Visual improvements to the engine bay.
COMPATIBLE VEHICLES
Year |
Model
|
Gen
|
Engine
|
2012-2019
|
Golf
|
MK7/7.5
|
1.8 TSI
|
2012-2019 | Golf | MK7/7.5 | 2.0 TDI |
2013-2019 | Golf GTI | MK7/7.5 | 2.0 TSI |
2014-2019 | Golf R | MK7/7.5 | 2.0 TSI |
2014-2019 | e-Golf | MK7 | Electric Motor |
2015-2019 | Golf SportWagen | MK7/7.5 | 1.8 TSI |
2015-2019 | Golf Alltrack | MK7/7.5 | 1.8 TSI |
Available for all accessory cap looks like this.
OIL CAP
WASHER FLUID RESERVOIR CAP
COOLANT RESERVOIR CAP
BRAKE FLUID RESERVOIR CAP
Regular Price: $999.00
Special Price $950.00
Leyo Motorsport’s CAI for the A4 B9 is a must have for those seeking to upgrade their car. By removing some factory air flow restrictions together with a massive 4 inch conical filter, this intake guarantees more horse power at an affordable cost.
High grade aluminum heat shield effectively blocks out excess heat from the engine bay while is also significantly lighter than the steel heat shields found on the market. A secondary heat shield is incorporated into the design to block excessive heat from the exhaust manifold.
Installation is easy and straight forward, no fabrication required.
*This product is only for use on the race track.
*Please note that if your car has air flow sensor on the inlet pipe, this intake does not fit.
Specifications:
4” high flow conical filter.
Aluminum heat shield.
Increased induction sound.
Easy installation.
Protect your engine by preventing excessive crankcase oil vapor entering the intake and carbon build up with LEYO Oil Catch Can Kit. Also known as blow-by, oil vapor is produced under load, spirited driving elevates oil vapor level at an incredible rate, it is then circulated back into the intake tract resulting in carbon buildup of the intake valve, trapped oil residuals in both intake tract and intercooler. Unfiltered recirculated oil vapor will not only diminish performance, but also impose devastating effect to the engine.
Filtration begins immediately as oil vapor enters the uniquely designed LEYO Oil Catch Can filtration system, allowing pressurized oil vapor to enter freely, accelerates condensation, effectively traps oil with specially designed perforated stainless steel plates before cleaner gases recirculates back into the intake tract. Made with T304 stainless steel and high grade aluminum ensuring rust free, leak free operation. LEYO Oil Catch Can Kit had also included pre-installed drain valve, protecting your pride and joy has never been easier.
Specifications:
Installs under factory engine cover.
Uniquely designed filtration system.
Pre-installed drain valve for easy draining.
Regular Price: $929.00
Special Price $836.00
This will replace OEM part numbers 06H 145 710D, 06F 145 710G, & 06H 145 710 C
Forge Motorsport is proud to release the latest version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CJXB, CZPA, and CJXC;US codes CPLA and CPPA) including Golf MK7 R
This valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. It has also been proven in cars running over 600bhp!
This new valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.
We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner
In The Box:
1 x FMDVMK7R Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker
Regular Price: $399.00
Special Price $319.00
The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team for the EA888 TSI vehicles, the Forge turbo blanket is designed to assist in the protection and prolonged life of the engine components.
· Stainless Steel Rivets
· Stainless Steel Fasteners
· Carbon fabric Outer Shell
· Calcium Magnesium Silicate Wool constructed Inner Core
· High temperature silica fabric
The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket.
Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers:
Interior Surface:
· Max Temperature Rating: 2300°F/1260°C
· Continuous Use Limit: 1832°F1000°C
Exterior Surface:
· Direct Contact Limit: 1800°F/982°C
· Radiant Heat Limit: 2500°F/1371°C
Complimentary Products