Vehicles - CTS Turbo - Integrated Engineering - 034Motorsport - INA
DESCRIPTION
CTS Turbo is proud to release our 3.0T Supercharger Pulley Upgrade for the Gen 2 3.0T, commonly found in late 2016-2018 B8.5 Audi S4/S5 as well as A6, A7, Q5, SQ5 and Q7
THIS IS THE BOLT-ON STYLE PULLEY KIT. CHECK ON YOUR CAR FOR COMPATIBILITY.
CTS pulley is a smaller diameter than stock. Stock pulley size is 63.25, the CTS pulley is 57.3mm; this will increase the speed at which the supercharger spins, increasing the boost pressure output. Increased boost pressure in conjunction with upgraded ECU software results in a dramatic increase in horsepower and torque throughout the entire powerband. This will not increase stress or excessive wear on supercharger or engine components.
NOTE: CTS 3.0T Supercharger Pulley Upgrade must be used with appropriate “Stage 2” performance software.
Stage 2+ performance software (not included) will allow you to achieve maximum boost and power from your 3.0T while safely optimizing air-fuel ratios, timing, and boost pressure bleed off.
Most Stage 2+ software tunes are compatible with this kit.
Product Details
- Made in house at CTS Turbo in Canada
- Precision CNC machined from billet ASI303 stainless steel – best on the market! No other pulley manufacturer uses this steel.
- OEM-spec honing and tolerances
- Boost increased from stock 11psi to 15psi, boost holds steady all the way up to redline
- Nitride coated for long-lasting OEM looking finish
- Includes belt and bolts required for install
- Stock Size: 63.25mm, CTS Size: 57.3mm
Fitment:
- 2016-2018 B8.5 Audi S4, S5, Q5, SQ5 with 3.0T SUPERCHARGED engine
- 2016+ C7.5 Audi A6, A7 with 3.0T SUPERCHARGED engine
- Late Audi Q7 with 3.0T SUPERCHARGED engine
PRODUCT FEATURES
- Eliminates excessive play from OE rubber bushings
- Greatly Reduces chances of missed shifts
- CNC machined in-house for precise fitment
- Bronze inner bushing to provide smooth pivoting without wear
PRODUCT DETAILS
Say goodbye to mis-shifts and eliminate unnecessary play in your shifter with IE billet shift cable end bushings!
Eliminate unnecessary play in your shifter with these billet shift cable end bushings. These two piece bushings are CNC machined in-house from 6061 aircraft aluminum with a special bronze inner bushing. They directly replace the rubber factory cable bushings that deteriorate over time causing excessive play in the shifter. When the factory bushings are worn out, shifts become less precise, causing you to miss shifts. Not only will you be missing shifts but, by not fully engaging gears in the transmission, you can even strip the teeth right off the gears. Includes a total of four bushings.
FITMENT
- VW - Golf R 2012-2012 (MK6) 6 speed transmisison
- VW - GTI 2009 (MK5) 6 speed transmisison
- VW - GTI 2010-2014 (MK6) 6 speed transmisison
- VW - Rabbit 2008-2009 (MK5) 5 speed transmisison
- VW - Jetta 2008-2009 (MK5) 5 speed transmisison
- VW - Jetta GLI 2008-2009 (MK5) 6 speed transmisison
- VW - Jetta GLI 2010-2014 (MK6) 6 speed transmisison
- VW - Jetta GLI 2014-2016 (MK6.5) 6 speed transmisison
Sale
VW has encountered a problem with the FSI camshaft and cam follower that could lead to damage to your engine's cylinder head.
This small part can play quite a big role in your engine's well-being. It conveys the movement of your camshaft into power for the high pressure fuel pump by riding directly on the camshaft lobe.
If it becomes worn to the point of breaking it can cause permanent damage to the camshaft, fuel pump, or both. It could also send metal particles into your cylinder head which can cause damage to moving parts. Without replacement, it is common for followers to have holes worn through them.
Replacing this follower as a form of preventative maintenance can save you from spending even more money and time replacing your fuel pump or camshaft from damage caused by a worn follower.
Regular Price:
$64.00
Special Price
$60.00
At CTS Turbo we are proud to announce our new air intake system for the Audi 3.0T and 3.2L FSI engines. The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our single piece CNC mandrel bent aluminum intake pipe allows for smooth entry of cold air into the the engine providing peak power gains ranging from 5-8HP. All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.
Only for B8 and B8.5 Audi S4/S5/Q5/SQ5 with 3.0T or 3.2L V6 engine!
Product Details:
- Mandrel bent aluminum piping with black powder coating
- Reusable air filter with inverted cone design
- 4 Ply silicon connector with stainless steel clamps
- Sealed air box with rubberized trim
- Bracketry to prevent rattling under engine torquing
- Billet SAI breather adapter and Billet bracket with SAI breather filter
- Gains ranging from 5-8HP
Installation guide can be downloaded here
Sale
CTS TURBO 8V.2 RS3/ 8S TTRS 2.5T EVO TURBO OUTLET PIPE
Regular Price:
$329.00
Special Price
$299.00
Sale
SHIFT FASTER, DRIVE FASTER
The IE DSG Tune for your Audi B8/B8.5 S4/S5 3.0T delivers increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control and additional transmission performance features when paired with a matching ECU tune. Acceleration times will greatly improve turning your tuned 3.0T into a fully rounded performance monster.
LEADING FEATURES
Lightning fast gear shifts
Higher shift points of 7200 RPM
Multiple launch RPMs: 3400, 3600, 3800, 4000
Drive shift mapping entirely reworked with an enthusiast in mind
Flashed directly through OBD-II Port (No TCU removal required)
Works flawlessly with all IE ECU Tunes
Unlimited launches (factory defaults to 200)
Increased clutch pressure on tap for higher torque without slip
Temperature protection remains for safety
Gear hunting reduced
Gearbox “Torque Limiters” removed
WHAT DOES A DSG TRANSMISSION TUNE DO?
IE’s Audi S4 (DL501 S-Tronic) DSG tune is all-inclusive and does not offer expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features and upgrades are included at one low cost. A great deal of sportiness is added to the tune while maintaining factory smoothness and driveability that you love about the S4. More aggressive launches and faster shifts are guaranteed to put a smile on your face. Also, expect acceleration and 0-60 times to improve dramatically from a larger useable powerband provided by the higher shift points.
REQUIRED FOR SELECT ECU TUNES
Required for S4 & S5 Stage 2 dual pulley files, your new transmission tune will no longer lug the engine in drive mode or short shift the larger powerband. Clutch clamping forces are increased so the transmission can safely handle and deliver the increased power and torque. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes.
ONE TUNE FOR ALL STAGES
IE’s DSG tunes are all-inclusive without any expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset for any level of hardware or ECU Tune Stage, one cost and you are covered for all and any future upgrades from Stage 1 to Stage 2 billion.
USER ADJUSTABLE LAUNCH CONTROL
The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup!
Available Launch Control RPMs:
3400 RPM
3600 RPM
3800 RPM
4000 RPM
*Some early model B8 DSG TCUs cannot have launch control added to them, as well as some replacement Mechatronics units. Non compatible TCU codes include, but may not be limited to 8K1927156AC and 8K1927156AD. You can use your IE Powerlink tool to check your TCU code. Other DSG tune features will function normally.
IE DSG TUNE TECHNICAL FEATURES
HIGHER SHIFT POINTS
Utilize the whole powerband of your supercharged 3.0T engine without the DSG interfering and shifting early.
DRIVE MAPPING REWORKED
The B8 and B8.5 S4 is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode.
INCREASED CLUTCH PRESSURE
Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive.
FLASHED THROUGH OBD-II PORT
There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes.
TAKE-OFF LAG REDUCED
The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop.
MULTIPLE LAUNCH RPMS
The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup!
FLAWLESS OPERATION WITH IE ECU TUNES
The IE DSG Tune and ECU Tunes were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 3.0T engine and transmission. Perfect for all IE Tunes from Stage 1 to dual pulley and throttle upgrades.
VEHICLE FITMENT
Audi - S4 2008-2016 (B8 & B8.5) 3.0T supercharged engines*
Audi - S5 Coupe 2013-2016 (B8.5) 3.0T*
Audi - S5 Cabriolet 2009-2016 (B8-B8.5) 3.0T*
*IE DSG tunes are available only for vehicles equipped with Audi's 7-speed S-Tronic transmissions. Does not function with manual 6-speed transmission cars.
Regular Price:
$1,199.00
Special Price
$1,100.00
Sale
Dual port boost tap allows for multiple boost references
CNC machined from 6061 Aluminium
Brass plug included
Regular Price:
$89.95
Special Price
$79.95
At CTS Turbo we are proud to announce our new air intake system for the transverse 2.0T FSI EA113 VW/Audi range of vehicles.
The air scoop works in conjunction with our sealed airbox to seamlessly force cold air into our 2.75″ air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 9-15WHP. By using a factory MAF position, you can be sure that fuel trims will remain perfect.
All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.
This intake kit is designed to be compatible with our FSI EA113 BOSS kits; intake pipe features 2x 1/8″ bungs and 1x 1/2″ bung for easy installation of BOSS kits. Plugs are included.
Product Details:
- Full 2.75″ Mandrel-bent aluminum piping with black powder coating
- Compatible with CTS BOSS kits, with provisions for easy installation
- Reusable 3″ air filter with inverted cone design
- 4 Ply silicon connectors with stainless steel clamps
- Air box with rubberized trim
- Bracketry to prevent rattling under engine torquing
- Gains ranging from 9-15WHP on stock vehicle, even more if tuned!
- No CEL, no fuel trim issues
Fitment:
- MK5 VW GTI incl. Edition 35 (2006-2008)
- MK5 VW GLI (2006-2008)
- MK5 VW EOS (2006-2008)
- MK6 VW Golf R (2012-2013)
- MK2 SEAT Leon (2006-2009)
- MK2 SEAT Cupra R (2006-2012)
- B6 VW Passat (2006-2010)
- 8P Audi S3 (2006-2013)
At CTS Turbo we are proud to announce our new 3″ air intake system for the 1.8TSI and 2.0T Gen1 and Gen3 VW/Audi range of vehicles. This kit includes parts that make it compatible with both generations of TSI engines!
The air scoop works in conjunction with our sealed airbox to seamlessly force cold air into our 3″ air intake system. Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing. Our 3″ CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 9-15WHP. By using a factory MAF housing (when equipped), you can be sure that fuel trims will remain perfect.
All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.
This intake kit is designed to be compatible with our TSI Gen1 BOSS kits; intake pipe features 2x 1/8NPT bungs for easy installation of BOSS kits.
Product Details:
- Full 3″ Mandrel-bent aluminum piping with black powder coating
- Compatible with CTS BOSS kits, with provisions for easy installation
- Reusable air filter with inverted cone design
- 4 Ply silicon connectors with stainless steel clamps
- Airbox with rubberized trim
- Bracketry to prevent rattling under engine torquing
- Gains ranging from 9-15WHP on a stock vehicle, even more, if tuned!
- No CEL, no fuel trim issues
GEN1 Fitment (EA888.1)
- MK5 GTI with TSI motor (2009)
- MK5 Jetta with TSI motor (2009-2010)
- MK6 GTI (2010-2013)
- MK6 Jetta GLI (2012-2013)
- EOS with TSI motor (2009-2016)
- Passat CC TSI (2009-2013)
- New Beetle TSI (2010-2013)
- Scirocco TSI (2008-2017)
- Audi A3 TSI (2009-2013)
GEN3 Fitment (EA888.3 non-MQB)
- Volkswagen Beetle (MK2)
- Volkswagen Jetta (MK6) 18TSI & GLI (2013.5-2018)
- Volkswagen Scirocco (MK3)
- Volkswagen Passat 1.8TSI & 2.0TSI (B7)
Sale
CTS Turbo is proud to announce our new intake system for the B9 AUDI A4, AllRoad, A5, S4, S5, RS4, RS5 (2017-2019 models)
We designed our system to work in conjunction with the OEM air scoop to seamlessly force cold air into the air intake system. Air then flows through our high flow 6″ velocity stack air filter for maximum engine performance.
Our single-piece proprietary moulded silicone couplers allows for smooth entry of air into the engine providing peak power gains ranging from 10-12HP on a stock car.
All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound. Turbo spool up and diverter valve release are a lot louder!
Features:
- Massive 6″ velocity stack filter, largest on the market
- 3.5″ silicone turbo inlet hoses for both 4-cylinder and 6-cylinder engines (5-ply construction, will not collapse)
- Heatshield to keep air temperatures as low as possible
- Easy install and perfect fitment
- Increased engine performance, less turbo lag
- Sporty sound under acceleration and loud pressure release
- Gains of 10-12HP on stock vehicles, tuned cars will gain even more!
- Kit comes with parts to install on 1.8T, 2.0T, 2.9T and 3.0T engines (fits MAF-LESS cars)
Fitment:
- B9 A4 (2017 – current)
- B9 AllRoad (2017 – current)
- B9 S4 (2018 – current)
- B9 A5 (2018 – current)
- B9 S5 (2018 – current)
- B9 RS4 (2018 – current)
- B9 RS5 (2018 – current)
Does not fit cars with MAF sensor.
Installation Guide S4
Installation Guide A4
Regular Price:
$699.00
Special Price
$579.00