The CTS Runner Flap Delete allows for the removal of the restrictive intake flappers from the factory intake manifold. The factory intake flappers can be a substantial restriction in modified vehicles, the CTS RFD is a must for any FSI owner that wants to minimize airflow restrictions and maximize power to the ground.
We are proud to release the new our CTS Turbo Stage 3 Fuel Pump Kit for MQB GTI, MK7 Golf R, and B9 A4/A5. As you may already know the TFSI fueling system has two separate fuel pumps, the LPFP (Low-Pressure Fuel Pump) and HPFP (High-Pressure Fuel Pump). While there are a number of options for HPFP available, including the Autotech HPFP, there are limited options for fortifying the low-pressure fuel system. CTS has developed a fully integrated fueling system, which utilizes a Walbro 450LPH E85 compatible in-tank fuel pump that is capable of supporting in excess of 500HP. If you’re looking for a fuel pump system to support all the power that your engine can handle look no further than the CTS Turbo Stage 3 Fuel Pump Kit for MQB GTI, Golf R, 8V Audi A3/S3 and MQL B9 A4/A5.
NB: please keep in mind that some modifications to your fuel pump basket is required. Some baskets differ from each other so installation should be performed by an experienced technician.
Torqbyte Controller is an optional add-on and strongly recommended when using E85 fuel and tuning.
Product Details:
– Genuine Walbro High Output in-tank 450LPH E85 compatible Fuel Pump
– Genuine Walbro Filter sock (may not fit all revision fuel pump baskets)
– CTS CNC machined/black hard anodized pump adapter
– CTS CNC machined/black fuel pump spacers
– CTS CNC machined/black fuel pump venturi standoff
– Viton O-ring
– Nylon wire crimps
– Drill bits
– Stainless steel fasteners
Fitment:
One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.
Regular Price: $184.00
Special Price $179.00
Regular Price: $769.00
Special Price $692.00
Regular Price: $929.00
Special Price $875.00
Regular Price: $769.00
Special Price $692.00
CTS Turbo is proud to release our 3.0T Supercharger Pulley Upgrade for the Gen 2 3.0T, commonly found in late 2016-2018 B8.5 Audi S4/S5 as well as A6, A7, Q5, SQ5 and Q7
THIS IS THE BOLT-ON STYLE PULLEY KIT. CHECK ON YOUR CAR FOR COMPATIBILITY.
CTS pulley is a smaller diameter than stock. Stock pulley size is 63.25, the CTS pulley is 57.3mm; this will increase the speed at which the supercharger spins, increasing the boost pressure output. Increased boost pressure in conjunction with upgraded ECU software results in a dramatic increase in horsepower and torque throughout the entire powerband. This will not increase stress or excessive wear on supercharger or engine components.
NOTE: CTS 3.0T Supercharger Pulley Upgrade must be used with appropriate “Stage 2” performance software.
Stage 2+ performance software (not included) will allow you to achieve maximum boost and power from your 3.0T while safely optimizing air-fuel ratios, timing, and boost pressure bleed off.
Most Stage 2+ software tunes are compatible with this kit.
Product Details
Fitment:
PRODUCT FEATURES
PRODUCT DETAILS
Say goodbye to mis-shifts and eliminate unnecessary play in your shifter with IE billet shift cable end bushings!
Eliminate unnecessary play in your shifter with these billet shift cable end bushings. These two piece bushings are CNC machined in-house from 6061 aircraft aluminum with a special bronze inner bushing. They directly replace the rubber factory cable bushings that deteriorate over time causing excessive play in the shifter. When the factory bushings are worn out, shifts become less precise, causing you to miss shifts. Not only will you be missing shifts but, by not fully engaging gears in the transmission, you can even strip the teeth right off the gears. Includes a total of four bushings.
FITMENT
Regular Price: $329.00
Special Price $299.00