Audi - OSIR - Turbosmart - H&R Springs - Integrated Engineering - P3 Cars - INA - Whiteline

Compatible with all Mk1 Q5 Models (8R)

P3 V3 Gauge Features

• Plug and Play Install - plugs directly into your OBD2 port (want to keep your OBD2 port open? hard-wire harness kit also available)
• OEM Integration - installs in your vent for a sleek install while retaining air flow
• Versatility - read boost from multiple OEM sensors through OBD2 port or using optional P3 analog boost sensor
• Code Reading/Clearing - read and clear diagnostic trouble codes (DTCs) on the fly

P3 V3 Gauge Readouts (all readouts can be individually configured to read in either Imperial or Metric units)

• Boost (through OBD2 port using OEM sensors or with P3 analog boost sensor)
• Coolant temperature
• Air/Fuel ratio (can be read in AFR or Lambda)
• Vehicle speed (can be calibrated in 1% increments from -9% to +20%)
• Intake air temperature (Charge Air Cooler Temp) "CAC-AIr" on 3.0T models
• Throttle angle
• Ignition timing
• Engine RPM
• Exhaust gas temperature
• Battery voltage
• Programmable shift light
• Analog input 1 (brown wire) can allow gauge to read any 0-5 volt linear output sensor
• Analog input 2 (blue wire) can allow gauge to read any 0-5 volt linear output sensor
• Acceleration timers (0-60mph/0-100mph/60-130mph)
• Braking timers (60-0mph/100-0mph)

OEM Vent Option

• We install the display in an OEM vent to make your install even easier

Optional Add-Ons

• P3 Analog Boost sensor - plugs directly into gauge harness, no wiring required)
• Boost tubing kit - Approx. 5' of 5/32" O.D. flexible plastic boost tubing with vacuum "T" and 3 sections of 5/32" I.D. vaccum hose. Includes 3 zip ties
• P3 ESVA (Ethanol Sensor Voltage Adaptor) allows your gauge to read ethanol content and fuel temperature directly from the common Continental/GM flex fuel sensor. *Ethanol sensor NOT included
• Trim Removal Kit - this tool kit will help you remove your vent and interior trim while minimizing the chance of scratching or damaging your trim
• OBD2 Splitter - attach multiple devices to your OBD2 port. *some devices will not function while another device is attached to the OBD2 port

You asked, we answered.

The P3 V3 Gauge adds even more user control to what the OBD2 Multi-Gauge already offered. Read DTCs on command, remove pids that you don't care to see, configure units settings of individual measurements, calibrate your vehicle speed, read AFR in Lambda.

There when you need it, hidden when you don't.

No more bulky pillar or column pods... No more squinting to read tiny pixelated screens...  While retaining the OEM plus design that blends into your interior, the P3 V3 packs a punch with it's bold, bright display that allows you to pick up info at a glance.

Hot or Cold? No problem!

Even though the P3 V3 installs in your air vent, we keep in mind that you need that heat and A/C while designing each gauge.

Electronics in a harsh climate? We've got that covered too.

We've torture-tested our gauges to the extreme. From frozen solid at -94 F to physically melting at hundreds of degrees, our gauges function far beyond the limits of the in-car environment.

Need more details? 

Check out the V3 install page for configuration and installation info.

• Australian owned
• 100% Fitment Guarantee
• Genuine quality brands

Front Lowering: 35mm
Rear Lowering: 35mm
Front Axle Weight: Up to 1100kg
Rear Axle Weight: Up to 1090kg

Sporty looks and performance
Progressive spring characteristics
Less weight by using high tension steel
TUV approved

H&R Sport Sway Bars are crafted from a special 50CRV4 steel alloy, the highest tensile strength available.

The quality of the material and design guarantees smooth transitional sway bar function, decreasing feedback response time and increasing stiffness over stock.

H&R Sport Sway Bars improve lateral stability and cornering grip, while reducing body roll. H&R Sport Sway Bars are designed for drivers who desire improved handling without lowering or affecting ride quality. H&R Sport Sway Bars increase stiffness and reduce body roll while maintaining comfort and increasing cornering control, lateral stability, and grip. 

A unique feature of H&R Sport Sway Bars are the smooth, machined-like forged ends that, for specific vehicles, allow for adjustability in stiffness.

Being 100% German made means a commitment to doing it right and giving you the best quality product.

Features:
- Reduces body roll
- Highest tensile strength available
- Works with DCC (adaptive suspension)

- Special urethane/Teflon composite bushes that are maintenance free

Swaybar Size:
- Front 24mm

- Rear 26mm

Adjustable:
- Front x2
- Rear x2

Compatibility:

• Audi A3 8P 2003-2012 4WD
• Audi S3 8P 2003-2012 4WD
• Skoda SUPERB 3T SEDAN 4WD
• Skoda OCTAVIA 1Z SEDAN + WAGON 4WD
• VW GOLF MK5 2003-2008 4WD
• VW GOLF MK6 2008-2012 4WD
• VW PASSAT B6/B7 2005-2014 4WD
• VW Tiguan 5N 2007-2015 4WD

The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.  

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!

PRODUCT DETAILS

IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.

MACHINED DESIGN

Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.

FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY

This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.

PRODUCT FEATURES

• Replaces factory plastic valve cover
• Uses factory valve cover gasket
• In-house CNC machined from aluminum
• Includes o ring sealed matching billet oil cap
• -10AN breather outlet for catch can setups

ADDITIONAL PARTS REQUIRED

EVAP CROSSOVER TUBE RELOCATION KIT

The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11

CATCH CAN KIT FOR BILLET VALVE COVER

The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3

VEHICLE FITMENT

• Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
• Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
• Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
• Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
• VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
• VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
• VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
• VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*

*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.

LEADING INTAKE FEATURES

• Increased airflow - Get the most out of your upgrades
• High-flow velocity stack - True performance design
• Sealed heatshield - Separates cold air from engine bay heat
• Perfect fitment - No modifications required to bolt-on
• Amazing sound - Releases awesome turbo and engine noise
• Looks great - Black powder coat, tight clearances, clean angles 

AUDI B8 A4 & A5 COLD AIR INTAKE

You're not just building a run of the mill bolt-on car with cheap imported parts. No, your Audi B8 A4 or A5 project deserves true performance designed mods and the best cold air intake available. This is not your average filter on a stick, IE engineers used specialized computer flow analysis software coupled with 3D scans of the engine bay to maximize performance. The result is a unique intake shape that optimizes flow and reduces air restrictions for an unmatched bump in power. Factory-like mounting solutions are used for a perfect fit and long life. Your new intake will fit like it was there stock, but perform and sound like a true motorsport intake design.

EASY INSTALLATION

Installation is quick and easy to install with basic tools. The process should take under an hour for most enthusiasts. CLICK HERE to view and download the IE B8/B8.5 A4/A5 Cold Air Intake Install Guide.

VEHICLE FITMENT

• Audi - A4 2009-2015 (B8-B8.5) 2.0T
• Audi - A4 Allroad 2009-2015 (B8-B8.5) 2.0T
• Audi - A5 2009-2015 (B8-B8.5) 2.0T