One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.
Regular Price: $184.00
Special Price $179.00
Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!
IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.
Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.
This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.
EVAP CROSSOVER TUBE RELOCATION KIT
The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11
CATCH CAN KIT FOR BILLET VALVE COVER
The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3
*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.
Regular Price: $769.00
Special Price $692.00
Regular Price: $769.00
Special Price $692.00
CTS Turbo is proud to release our 3.0T Supercharger Pulley Upgrade for the Gen 2 3.0T, commonly found in late 2016-2018 B8.5 Audi S4/S5 as well as A6, A7, Q5, SQ5 and Q7
THIS IS THE BOLT-ON STYLE PULLEY KIT. CHECK ON YOUR CAR FOR COMPATIBILITY.
CTS pulley is a smaller diameter than stock. Stock pulley size is 63.25, the CTS pulley is 57.3mm; this will increase the speed at which the supercharger spins, increasing the boost pressure output. Increased boost pressure in conjunction with upgraded ECU software results in a dramatic increase in horsepower and torque throughout the entire powerband. This will not increase stress or excessive wear on supercharger or engine components.
NOTE: CTS 3.0T Supercharger Pulley Upgrade must be used with appropriate “Stage 2” performance software.
Stage 2+ performance software (not included) will allow you to achieve maximum boost and power from your 3.0T while safely optimizing air-fuel ratios, timing, and boost pressure bleed off.
Most Stage 2+ software tunes are compatible with this kit.
Product Details
Fitment:
Complete the aggressive aesthetic of your RS3 8V Sportback (Pre-facelift) rear with our rear pods/spats - known for their durability and strength. Our newly developed RS3 Sportback Pre-facelift range shares the same strength, durability and technology as our popular Audi S3 and Golf R line up which is trusted by many enthusiasts. Pre-pressed brass fittings on the rear pods allow for installation of our adjustable rear pods/spats winglets (sold separately) to allow for further customisation to individual taste.
All our lip splitters are made from a thick polyethylene composite, making it the strongest product of its type on the market. Each splitter is model specific in its development and design to ensure perfect fitment. The entire production process is done is our Bayswater factory making us proudly Australian made and owned.
MATERIAL & FINISH
Each splitter is developed to become an integral part of your stock body kit, giving it unrivalled rigidity and strength so it can absorb scrapes and protect your bumper.
Strong, impact-resistant, doesn't corrode or chip, and has excellent abrasion resistance (eg. scraping on driveways!)
As strong and light as carbon fibre is, it cracks on impact or when under load and/or stress. Clearcoat can eventually fade or crack, becoming undesirable.
Please note that although all our precision-made ABS accessories are extremely strong and durable, they do not hold the same shatterproof label as our 10mm thick polyethylene composite splitters. The accessories are manufactured in ABS with the intention that they will be lighter, bolt-on attachments that will improve aesthetics and are easily replaceable if they become damaged from varying road conditions.